-
Product
Energy Dispersive X-ray Fluorescence Spectrometer
Pharmaceutical Elemental Impurities Analysis System
-
Control of Elemental Impurities in Pharmaceuticals In the pharmaceutical industry, the analysis of elemental impurities is necessary to ensure the safety of pharmaceuticals. In December 2014, the "Guideline for Elemental Impurities" (Q3D) was issued by the International Council for Harmonisation of Technical Requirements for Pharmaceuticals for Human Use (ICH), consisting of representatives from Europe, the U.S. and Japan. In Japan, the "Guideline for Elemental Impurities in Drug Products" (PFSB/ELD Notification 0930 #4 from the Ministry of Health, Labour and Welfare) was issued, and will be applied to new drug products submitted for approval after April 1 2017. For 24 elements categorized in Class 1 to Class 3, residual quantities in pharmaceutical drug products must be controlled within permissible limits. Although ICP-AES and ICP-MS are used for precise analysis of elemental impurities, X-ray fluorescence spectrometers can be used as an alternative analysis method. This is because they can quantitatively and qualitatively analyze a variety of elements nondestructively, and without chemical pretreatment, unlike ICP-AES and ICP-MS systems. The X-ray fluorescence spectrometry has been adopted as a general method of analysis in the U.S Pharmacopeia and the European Pharmacopoeia. (USP<735>, Ph.Eur.2.2.37)
-
Product
Fully Automatic Close Link Three Phase Energy Meter Test Bench
SY 8320
-
Hong Kong Songyang Industrial Ltd.
Suitable design, good figure. The frame for meters and the body frame are fully made by special aluminum alloy. The table board is composed of fireproofing and heat-proof fiber materials. The whole device is in soft color and good figure.
-
Product
76kWh Lithium Battery 384V 200AHSolar Energy Storage LiFePO4 battery System
SPVLI-76KWH
-
Zhejiang Sandi Electric Co., Ltd
SANDI ESS lithium battery system is composed of lithium battery modules, BMS system, PV charge controller, AC/DC Charger, central control unit CCU, temperature detector, integrated structure and other parts; the solar panels in the system are battery storage and power for output; BMS module completes the detection and control of voltage, current, temperature, SOC, SOH and charging and discharging related parameters of power battery pack; PV controller and inverter realize bidirectional AC/DC function to meet the charging and discharging conversion demand of power battery pack; each detector is used to monitor the ambient temperature in real time to ensure the safety of the system.
-
Product
Spectroradiometer For Measuring Natural And Artificial Solar Radiation
-
UV-visible-NIR spectroradiometers with accessories for measuring solar radiation - natural daylight and solar simulators
-
Product
Power and Energy Automated Calibration System
RS-933
-
The RS-933 Syntron Power and Energy Automated Calibration System calibrates a range of test equipment including; Energy Reference Standards, Digital Multimeters, Phase meters, Energy meters, Power meters, Revenue meters, Amp meters, Panel meters & Power Quality meters.
-
Product
Solar Test Systems
-
AMETEK Scientific Instruments manufactures a range of application specific XM (Xtreme Measurement) products focused on solar cell / photovoltaic research (developed in collaboration with Professor Laurie Peter of the University of Bath, UK). These products are so versatile that they can also be used for photoelectrochemical (PEC) water splitting applications; and make use of Solartron’s unique high performance XM specified potentiostats and frequency response analyzers to provide a full complement of techniques for research into energy, corrosion and analytical electrochemistry.
-
Product
Ultrasonic Energy Meter
Series TUF
-
The SERIES TUF Ultrasonic Energy Meter is a highly accurate and stable energy meter that utilizes ultrasonic technology to measure heating and cooling energy consumption. The Series TUF is a compact meter with a flowmeter and energy calculator in one, making it great for installation on chillers and boilers.
-
Product
Solar Photovoltaics
-
The conversion of light into electricity using semiconducting materials that exhibit the photovoltaic effect, a phenomenon studied in physics, photochemistry, and electrochemistry.
-
Product
Wireless MCU With Integrated Wi-Fi 6 And Bluetooth Low Energy 5.4
AIW-411
-
NXP RW612 Arm Cortex®-M33Integrated Wi-Fi 6 and Bluetooth® LE 5.4Rich Industrial I/O Interfaces:USB 2.0 OTG *1, PSRAM *1, Ethernet RMII *1, SDIO 3.0 *1, UART *2, SPI *1, I²C *2, PWM *3, JTAG *1, ADC *2NXP MCUXpresso SDK CompatibilityOSM Size-0 Compact Design (30 x 15 mm)
-
Product
Solar ATE
MS 1534
-
The Inverterless ATE is an automatic test equipment which is used to test the all functional and various test conditions of Inverterless Solar Unit. This ATE shall be a GO/NOGO Tester for Inverterless Solar Unit. All production units can be tested with this ATE for functional testing and clearance. This ATE reduces the man effort for quality checks and detects the failure units. The Inverterless ATE can check the UUT with minimum user interactions. It shall test and generate test report in PDF format for the conducted tests with necessary data. The ATE operates on 230V AC power. The ATE has In-Built AC-DC converter which provides 12V DC for operate the unit. Also it has additional AC-DC converter to simulate solar power to the Inverterless units. The main objective of the ATE is to test the Inverterless S in all possible test scenarios without external test equipments and less user interactions.
-
Product
Green Energy Testing
-
MET is a pioneer in the testing and certification of energy efficient and alternative energy products, such as solar panels, wind generators, and inverters.
-
Product
Solar Cell I-V Characterization System
VS6825
-
Industrial Vision Technology Pte Ltd.
The VS-6825A I-V test system is tailored for high-efficiency Solar cell production lines. It is able to eliminate the impact of HJT/IBC/TOPCON’s high capacitance characteristics on measurement results.
-
Product
Long Life Seismic Energy Source
1900LLX-T
-
Output volume of 10 cubic inches to 250 cubic inches. Light weight enough for shallow draught vesselsPowerful enough for blue water seismic surveys. Available with engineered seals for more robust performance.
-
-
Product
Portable Test Bench for Single Phase Energy Meter
SY2100
-
Hong Kong Songyang Industrial Ltd.
The new SY2100 series Portable electricity meter test equipment, designed from new DIGITAL WAVE COMPOUND TECHNOLOGY and according to International Standard, is newly intelligent equipment for energy meters. The equipment includes voltage/current source & standard meter, operated easily through front panel to preset directly all data of meter under test and test process.
-
Product
Solar PV Test Equipment
-
The Seaward Solar range of electrical solar PV test equipment enables Photovoltaic installers to meet all testing and certification requirements of IEC 62446 safely and efficiently.
-
Product
Fully Automatic Solar Cell
Module Laminator-H
-
1. Model: BSL2236OAC-H2. Effective lamination area: 2200mm × 3600mm3. Dimensions: length 17410mm × width 3665mm × height 2164mm4. Heating method: heat conduction oil heating5. Compressed air source pressure: 0.6～0.8MPa6. Working vacuum degree: 100～40Pa7. Evacuation rate: 70L/S8. Temperature control accuracy: ±1.5°C9. Temperature control range: room temperature - 180°C10. Temperature uniformity: effective lamination area≤±2℃11. Lamination chamber height: 30mm12. Evacuation time: depending on the process, it is recommended to take 5 to 8 minutes13. Upper cover stroke: 300mm
-
Product
Solar Simulators
-
Abet Technologies offer a wide range of ASTM, IEC, and JIS standards compliant solar simulators ranging from 150W to 3kW with one sun or greater illuminated field sizes from 50 x 50 mm to 35 x 35 cm. The direction of illumination, traditional down pointing, horizontal, or vertical up pointing can be specified at the time of ordering.
-
Product
Single Phase Multi-Tariff Energy Meter Type DDSF999
-
Bofa Instrument & Equipment Co., Ltd
Single phase multi-tariff energy meter type DDSF999 is used to measure 50HZ AC active energy and the power flow of peak, shoulder, flat and valley time. All of its functions comply with the relative technical requirements for class 1 single-phase watt-hour meter in IEC61036-2000, and its data communication rules obey the requirements of IEC1107
-
Product
Display of Energy Yielded by Photovoltaic Plants
VisiKid
-
It enables the direct conversion of sunlight into electrical energy through solar cells - that is why photovoltaics is one of the most popular sources of renewable energy; that is why solar power plants are increasingly being installed on the roofs of nurseries and schools. The aim is both to set an example and teach children about renewable sources of energy.
-
Product
Solar Array Simulator Auto-Ranging Module 0-160V, 0-10A, 1kW
MP4361A
Simulator
The Keysight MP4361A is a 1000 W solar array simulator DC power module that simulates the output characteristics of a solar array. The MP4361A is primarily a current source with very low output capacitance. It offers fast I-V curve changes allowing you to accurately simulate the output of different solar arrays under various environmental conditions (ex. temperature, age, eclipse, spin, etc.).
-
Product
Light and Energy Meter
Model 659
-
UV Light and Energy Meter for use with all wafer steppers. For over 45 years, OAI is a world leader in UV Light and Energy Measurement Instrumentation used for reliable accurate calibrated control of the photolithography processes in the Semiconductor, MEMS, Wafer Packaging and Wafer Bumping Industries. The New Model 659 is an advanced UV exposure analyzer specifically designed for use with all wafer steppers including high intensity wafer steppers. This meter averages up to 400 exposure readings, has Ethernet and USB interface for downloading recorded measurements, and has intensity range of up to 7,500mW/cm2. Probes are available in wavelength of 365nm, 400nm, 420nm & 436nm. OAI has a complete certified calibration lab to maintain the performance, quality and reliability of our meters. The Model 659 meter is traceable to NIST standards.
-
Product
FIber Based Solar Simulator
-
Provides up to 12 suns class B non-uniformity over a 12.5 mm diameter with the A4 Light Line and class C uniformity can be achieved over 18mm diameter both with a working distance of 25 cm. Provides up to 4 suns class B non-uniformity over a 12.5 mm diameter with the A1 Light Line with a working distance of 25 cm.
-
Product
Datapaq Solar Tracker System
-
The SolarPaq® Thermal Profiling Systems from Fluke Process Instruments are designed specifically for solar photovoltaic (PV) manufacturing including applications like contact firing, contact drying, anti-reflection coating for the solar cell, lamination and other thin film processes. These systems, consisting of user-friendly Insight™ software, Datapaq® Q18 data loggers, stainless steel thermal barriers, thermocouples with PTFE or mineral insulation and accessories, provide users with the tools needed to gather accurate, repeatable results for process optimization, maximize cell efficiency and throughput, and more.
-
Product
Solar Cell Simulation
Setfos
-
Setfos excels in analyzing and fitting experimental data, providing researchers with valuable insights and trend predictions. Complement your experimental work with Setfos for unmatched accuracy and reliability in data interpretation.
-
Product
Solar Simulation Systems
-
Solar simulation systems with global radiation guarantee the simulation of natural sunlight according to CIE20 and CIE85 Table 4. Our portfolio includes components, systems and systems for solar simulation for test benches in the automotive, military, aerospace, railway, photovoltaic, material research and building materials industries. Our plants and systems stand for high reproducibility and precise test results.
-
Product
Contact Probe for Solar Panels
TP878.1SS.O
-
Contact temperature probe for solar panel. 1/3 DIN 4-wire Pt100 sensor.
-
Product
Solar Panel Chamber
-
Specifically designed for the solar industry, these climatic chambers feature specifically designed fixtures to properly measure almost any component related to solar panels including the actual panels, grid-tied photovoltaic inverters, or photovoltaic cells and modules.
-
Product
Energy Dispersive X-ray Fluorescence Spectrometer
EDX-LE
-
EDX-LE is an X-ray fluorescence spectrometer designed specifically for screening elements regulated by RoHS/ELV directives. The model uses a detector (Si-PIN semiconductor detector) that does not require liquid nitrogen, thereby achieving lower operation cost and easier maintenance. Automated analysis functions improve operability without sacrificing its high level of inspection reliability. The time required from start of measurement to judgment is as short as one minute for some samples, which is very helpful in screening inspections for elements regulated by the RoHS directive.
-
Product
Energy Analyzer
EP600i
-
The EnergyPro EP600i is portable and easy to use. Perfect for single phase or three phase energy consumption analysis and basic power quality monitoring. It supports standard wiring configurations and comes with a set of 1A - 2500A WideRangeFlexCT ™. The graphics display makes setup very easy and intuitive - you can setup and record data without looking at the manual!
