Filter Results:
Products
Manufacturers
Applications
Bluetooth Low Energy
minimal power required WPAN. Also known as: BLE,Bluetooth Smart
See Also: Bluetooth, Bluetooth Test, WPAN
-
product
High Performance Polyphase Energy Metering AFE w/ Power Quality Analysis
ADE9000
The ADE9000 is a highly accurate, fully integrated energy-metering device. Interfacing with both current transformer (CT) and Rogowski coil sensors, the ADE9000 enables users to develop a three-phase metrology platform, which achieves high performance for Class 1 through Class 0.2 meters. Power quality features enable advanced meter designs with fast rms measurements and power quality level monitoring for EN50160 compliance. The ADE9000 integrates seven high performances ADC’s, a flexible DSP core. An integrated high-end reference ensures low drift over temperature with a combined drift of less than ±25 ppm/°C max for the whole channel including PGA and ADC.
-
product
Portable Wattneter (Low Power Factor 0.2)
Supreme Instrument Laboratories
Range : 0-0.5/1 Amps, 0-50/100/200 Volts.0-0.5/1 Amps, 0-75/150/300 Volts0-0.5/1 Amps, 0-150/300/600 Volts0-0.5/1 Amps, 0-125/250/500 Volts
-
product
Energy Analyzer
VIPENERGY
Measurements on distorted and unbalanced systems. Display with backlight. Easy to install and operate. All options can be programmed on the field. Signal outputs: versions with different configurations available for expanding the use of VIP ENERGY to industrial control applications.
-
product
Universal Multichannel Low Voltage Power Supply System
SY8800
- Factory configured modular system- 5 free slots for power supply modules- 3U x 19″ x 35 cm crate size- Floating channels- Local and Remote Control- Remote control via Ethernet, USB, CANBUS and RS232- Max output power: 2.5kW @ 220Vac, 1.5kW @ 115Vac- Up to 8 independent channels- Low noise
-
product
Low Frequency Test Systems
Ingenieurbüro Dr. Hillger Ultrasonic-Techniques
Our imaging low-frequency inspection systems are excellently suited to displaying internal defects with high resolution and high dynamics.
-
product
Low Thermal EMF Relays
Series 100
The Pickering Series 100 is a complete range of Single-in- Line (SIL) reed relays primarily intended for direct drive from 4000B CMOS or similar low current sources. They feature a very low level of thermal EMF.
-
product
7U 21 Slot VME64 Low Cost Crate
VME8010
The Mod. VME8010 is a 21 slot VME crate, suitable for 6U x160mm boards, with VME64 compliant backplane. A 1U space is reserved for Fan Unit. The Unit is powered by 100÷230 VAC, 50 ÷ 60 Hz. The power distribution is +5V@60A, -12V@6A, +12V@8.9A.
-
product
Energy Probes
RjP-700 Series
The RjP-700 Series probes are designed to measure lower pulse repetition rate, longer duration pulses - up to 1msec pulse width at a maximum rep rate of 40Hz. This allows for measurement of pulsed flashlamps and other sources not possible with other probes. The combination of large area detector surface and long pulse width allow for measurements up to several Joules total energy. Integrated preamplifiers allow for longer probe-to-instrument cable runs, useful for manufacturing environments.
-
product
SHC68-C68-D4, Shielded Single-Ended Cable, Low Leakage, 1m
152870-01
68-Pin, Male VHDCI to 68-Pin, Male VHDCI, 50 Ω, Shielded Digital Cable - The SHC68-C68-D4 Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments with other NI accessories like the CB-2162 Connector Block or SMB-2163 Terminal Block. You can also use it with certain Digital I/O Adapter Modules for FlexRIO, Digitizer Adapter Modules for FlexRIO, Signal Generator Adapter Modules for FlexRIO, and high-speed serial instruments. It is flexible and easily fits around custom test fixtures and other equipment. It is a shielded, 50 Ω cable and is offered in different lengths.
-
product
Low Profile PCI Express 4-Port
7402e
The 7402e low profile PCI Express serial interface provides four serial ports, each individually field-configurable for RS-422 or RS-485 communications. The board uses a 16C954 UART with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data intensive applications. This high-performance UART includes 9-bit framing support and is register compatible with legacy 16550 software applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
product
Ultra Low Level DC Voltage Amplifiers
The EM A10 is a low level amplifier module for sensitive measurements, data collection and systems, where signals below 1 nanovolt may be measured. It is ideal for the input unit for precision voltage measuring systems, requiring voltage sensitivity for measuring low noise and low impedance sources. The noise level of the A10 is equivalent to a perfect resistor of about 20 ohms. When used with a digital voltmeter, steady one nanovolt digits may be displayed, with a response time constant of less than a second. The input voltage stability of the A10 is very high, with the drift around a nanovolt per degree C. The input connectors are made from pure copper. The input impedance is very high, and is time dependent, determined by the loop gain.
-
product
7.5 GHz Low Capacitance ÷10/÷20 probe
PP066
The PP066 is a high-bandwidth passive probe designed for the use with the WaveMaster™ and other high-bandwidth oscilloscopes that have 50 Ω input termination. This very low capacitance probe provides an excellent solution for higher frequency applications, especially the probing of transmission lines with 20–100 Ω impedance.
-
product
Low Level DC Current Data Logger
Process101A
The Process101A is one of MadgeTech's newest data loggers. It is part of a new series of low cost, state-of-the-art data logging devices. MadgeTech has taken the lead in offering the most advanced, low cost, battery powered data loggers in the world today.
-
product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-01 And WMA-01LF
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
product
Charger and Low Voltage Power Supply
FlexiCharge FC1500
The FC1500 Medical Capacitor Charging power supply, with a built in configurable ACDC power supply is designed to provide the system power needs for Medical laser applications. The FC1500 can provide both capacitor charging and ACDC low voltage system power due to it’s unique design and intelligent control. The FC1500 can be used as a standalone capacitor charger, and if needed, various low voltage modules can be added to the unit to provide further system power. This functionality provides extra flexibility to power other systems and applications. Low voltage modules can be connected in parallel and in series for application that require higher voltage and current requirements. The Capacitor charger capabilities has the highest level of performance due the unique built in intelligent control for capacitor charging, higher charge rates and power limit control.
-
product
Low Power Analog to Digital
7430
Smart A/D for thermocouples, thermistors, RTD's, strain and pressure gauges8-channels of 16-bit A/D resolutionEliminates trimpot adjustments by using software calibrationPerforms concurrent 32-bit floating point operations to minimize host computer loadingEach channel is software programmable for sensor type, gain, low-pass filtering, scan rate
-
product
Low Noise Differential Preamplifiers
Provide a high gain amplification to 1MHz with an AC output derived from a very low noise FET instrumentation amplifier. Each model has fixed gain settings of x1 (0dB), x10 (20dB), x100 (40dB) and x1000 (60dB) over a selectable bandwidths of 100Hz, 1kHz (HP), 3kHz, 30kHz, 100kHz and 1MHz (7000 model only). Noise referred to input is 7nV√Hz and common mode rejection is >100dB at 1kHz. Momentary pushbutton switches are provided that control coupling, bandwidth, gain and channel on/off selections. BNC connectors are provided for single-ended and differential input, ac output, and dc output (optional) connections.
-
product
High Accuracy Low Pressure Environment Pressure Switch
P100G
The P100G High Accuracy Low Pressure Environment Pressure switches are ideal in light pressure applications where precision of setpoint must be high and repeatability low. These switches are commonly used in natural gas well heads, natural gas generator sets, and air applications like forced draft blowers. The P100G can be used both in dry indoor applications or within an enclosure.
-
product
For Detecting Low Range And Leakage AC/DC/Pulsed Current.
FDAZCT-20LSP-0.6S
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Lowest Influence from Magnetization,Temperature *Change,Residual Current and Terrestrial Magnetism.*Low Cost and High Performance (Output Linearity ±1% F.S)
-
product
Low Inductance BNC Cable, VOLT:DC 60V
PX0105A
The Keysight PX0105A is suitable for narrow current pulse measurement down to 10 μs pulse width. It supports the Keysight M9602/03A.
-
product
Low Acoustic Noise and Compact Range
m-series
DC powered cooling fan is built-into the shaker. Natural air cooling is also used when the cooling fan is stopped for silent operation. (with a reduction in performance)
-
product
Low Current Probe 80A
695
Great tool for accurate measurement of low current. Use with your graphing meter or lab scope to view current waveforms on fuel injectors, fuel pumps, primary ignition coils and more. Also works very well with digital multimeters. Resolution of 10 milliamps is low enough for most parasitic drain testing. In addition, the clamp opening of 1/2 inch is large enough to clamp over most negative battery cables for those parasitic drain tests.
-
product
3-Phase Power and Energy Analyser
PQ55A
* Cpmprehensive real-time monitoring, recording and analysis of 3-phase systems* Voltage measurement (true RMS)* Current measurement (true RMS)* Power factor measurement* Phase angle measurement* Power analysis (active, apparent and reactive power)* 4. Current clamp for neutral line current measurement* Suitable for use in housing construction, offices and small businesses
-
product
Surface & Volume Low Resistivity Meter for Conductive Materials
Loresta GP
The Loresta GX Meter is an intelligent, multi purpose low resistivity meter equipped with software that calculates resistivity correction factors. A variety of 4 pin probes are available for use with the Loresta GX. The instrument is typically used in Product Engineering, R&D, and Quality Control. Applications include measurement of conductive paint, conductive plastics, conductive rubber, conductive film, silicon wafers, antistatic materials, EMI shield materials, conductive fiber, conductive ceramics, etc.
-
product
Low Power SNMP AGC FTTB Optical Receiver
BGL1000
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai BGL1000 product series, is a low power consumption, high index, with SNMP network management, AGC, full function FTTB optical receiver. 1000 series’ shells are aluminum wall hung (without rain-proof), Nixie tube displaying parameters.
-
product
Total Energy System
5000
The electric vehicle (EV) charging market is rapidly expanding, with more and more people switching to electric cars. As the demand for EV charging stations increases, so does the amount of energy that is being exchanged. This energy exchange market is already massive, with charging peaks reaching into the megawatts of energy. With this amount of energy comes a significant amount of revenue, which requires the most accurate billing possible. That’s where TESCO’s Catalog No. 5000 – Total Energy System comes in. The Catalog No. 5000 is a double duo system that enables the testing and accuracy verification of Electric Vehicle Service Equipment (EVSE) and Field Test Equipment for testing EVSE’s in the field. This system is a dual-purpose DC and AC System and includes both a 100A AC (ACT-100) Test System and a 200A DC Test System (DCT-200).
-
product
Low Phase Noise Amplifiers
Pasternack's low phase noise amplifiers cover select frequency bands ranging from 1.5 to 18 GHz with residual phase noise levels as low as -180 dBc/Hz @ 10 KHz offset. Additional performance specs include small signal gain ranging from 9 to 14 dB, with typical noise figure of 5.5 dB. Psat levels for these amplifiers range from +16 to +25 dBm with Output IP3 levels as high as +34 dBm. All models feature single DC voltage supplies and input/output RF ports are internally matched for 50 ohms with DC blocking capacitors. These compact module assemblies require no external components and are available in rugged Kovar metal drop-in packages that are gold-over-nickel-plated and support field replaceable SMA connectors. All models are EAR99 and guaranteed to meet MIL-STD-883 test conditions for hermeticity and temperature cycle.
-
product
PC Controlled Low Voltage Testers
PC Based Testers Low Voltage Introduction. The PC based analyzers provide high-speed testing for wire harnesses, backplanes, and printed-circuit boards.
-
product
Energy Metering ICs
Analog Devices’ ADE energy measurement ICs address the challenges of next-generation smart meter architectures and are ideal for measuring active energy (kWh), apparent energy (kVA), reactive energy (kVAR), rms, and power quality with the highest accuracy in single phase and polyphase revenue meters, industrial instruments, and energy monitoring applications. ADI’s ADE energy measurement ICs combine analog-to-digital converters with fixed-function digital signal processors to perform critical measurements, while providing unparalleled functionality and ease of use.
-
product
16 Channel Low Threshold Discriminator
V814
The Mod. V814 is a 1-unit wide VME module housing a 16 channel low threshold discriminator. The module accepts 16 negative (positive on request) inputs and produces 16 differential ECL outputs with a fan-out of two on four front panel flat cable connectors.
