-
product
Wind-Noise Reduction System
WNRS
The Wind-Noise Reduction System (WNRS) is an array of air inlets connected with pipes to reduce wind-noise and improve signal quality.
-
product
Leak Detection Oil
The faster, safer and easier way to locate even tiny leaks in industrial air conditioning and refrigeration systems. Lumirati® bottled dyes can be poured directly into any AC&R system. The dye can remain safely in the system to confirm repairs and perform future preventive maintenance checks. Lumirati® Leak Detection Oil is the only dye that gives you all these benefits:- Universal dye that is compatible with all refrigerants and lubricants- OEM-approved by major compressor, refrigerant, lubricant and AC&R equipment manufacturers- Co-solvent free so dye will not impair lubricant properties, which could lead to excessive wear or damage to the system components
-
product
Indoor Air Quality
Measuring Indoor Air Quality (IAQ) is an important factor since poor air quality may cause tiredness, inability to concentrate, and even illness (i.e., Sick Building Syndrome). Our IAQ meters measure CO2, Humidity, Dew Point, Air Temperature, Wet Bulb Temperature, and Oxygen (O2).
-
product
Fuel Hose Assembly Tester - Basic, USAF
9901-10FHT
The basic fuel hose assembly tester is utilized by those users who do not require the complete 9201A test system which includes all test adapters and components required by U.S. Air Force PD 89MMI638. The 9901-10FHT however includes the identical test pump, manifold and controls and with larger valves, ports and fittings for increased fluid flow, is designed for the identical mission of testing fuel hose assemblies. Maximum pressure is 1000 psi allowing better control resolution at lower test pressures.
-
product
Electronic Circular Temperature Chart Recorder
The Circular Temperature Chart Recorder’s external stainless steel probe allows you to measure the temperature of air, gas, liquids and semi-solids. The temperature chart recorder has a quartz clock movement, motorized chart advance and temperature accuracy of ±2°F (±1°C). The chart recorder comes in °F or °C models and runs on 120V or 220V AC, 50/60 Hz. A rear compartment houses 8 AA alkaline batteries, providing up to 48 hours of continuous recording in the event of a temporary power loss.
-
product
Rack Mount Thermometer Hygrometer
H3531R-2
Sensor H3531R is designed for online monitoring of temperature, relative humidity of air without aggressive substances. Three binary inputs to detection of two-states signals are the advantage. Other devices are controlled by two relay outputs. High precision capacitive polymer sensor ensures excellent long term calibration stability and ultimate accuracy. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
product
Standard Class AAA Solar Simulator
TriSOL TSS
Essential for testing virtually any material or product that is exposed to sunlight for long or short periods of time, OAI’s low-cost, Standard Solar Simulators deliver highly collimated, uniform light. Depending on configuration, output on these Solar Simulators is rated at 350W -5,000W.These Class AAA Solar Simulators feature OAI’s Advanced Uniform Beam Optics and are available with a choice of air mass filters to reproduce a wide range of solar spectra. For added flexibility, OAI’s proven lens and collimating mirror technology allows for a variety of exposure area sizes. A Class AAA Solar Simulator is an essential tool for manufacturing as well as R&D; it is indispensable in test labs, industry, and in universities. OAI Standard Solar Simulators are used in photobiology, biomedical, solar cell testing, cosmetic testing, and paints & coatings analysis. Based on 35+ years of proven UV light technology, OAI Solar Simulator Systems deliver repeatable, reliable, constant output, and measurement uniformity.
-
product
ThermalAir Desktop Series Temperature Forcing System
ThermalAir TA-1000A Desktop System
The ThermalAir TA-1000 high capacity thermal air stream system is used for temperature testing, fast thermal cycling, and device temperature characterization of components, hybrids, modules, PCBs, and other electronic and non-electronic assemblies at precise temperature from -25°C to +200°C.
-
product
Capacitance Measurement Trainer Module
Unitech Scales And Measurements Pvt. Ltd
Capacitance Trainer comprises of parallel plate/angular capacitor with dielectric medium air as sensor, mounted on the base plate with scale for displacement. Digital indicator is provided to read the change in capacitance in terms of displacement.
-
product
Single Sided PCB
Amitron produces prototype, midrange and high volume Single Sided circuit boards, with a copper thickness from one to twenty ounces. Operating temperatures range from 130 C to 230 C. Single sided boards are available with surface finishes including Organic surface protectant (OSP), Immersion Silver, Tin, and Gold plating along with both leaded or lead-free Hot Air Solder Level (HASL).
-
product
VHF/UHF Nav/Drone Analyzer
EVSD1000
The R&S®EVSD1000 VHF/UHF nav/drone analyzer is a signal level and modulation analyzer for use aboard medium sized drones. It measures ILS, GBAS and VOR ground stations during startup, maintenance and servicing and analyzes air traffic control communications (ATC COM) signals. The mechanical and electrical design is optimized for drone based measurements of terrestrial navigation systems.
-
product
Restrained Airspeeds
These airspeed indicators have restrained movements.These instruments are actuated by ram air and ambient atmospheric pressure obtained from the aircraft pitot and static pressure systems. A moveable pointer and a fixed dial indicate airspeed with the zero index at the 12 o’clock position. Temperature compensation is internal and there is no external zero adjustment. Pointer damping is internally adjustable.
-
product
5G | OTA | Bluetooth | PTCRB Testing Services
Eurofins E&E Wireless Device Over-the-Air (OTA), 5G Performance, Bluetooth, PTCRB, and Global Certification Forum Testing.
-
product
DC Switching Power Supply
MPS-3206
OVP and OCP to ensure the safety, smart fan, unique air duct design keeps normal temperature for long time full load working with low noise.Pure copper terminal makes good conduction, have better performance.110V/220V Input voltage switching.4 Digits Readings LED Display and 10mV and 1mA resolution,5 groups of parameter storage, coding switch to avoid casual touch.Easy to adjust voltage and curent through the knob, and we added an output button to prevent accidental touch.24 hours continuous operation, with high stability, suitable for a variety of working environments.
-
product
7U centrifugal 330 cfm blower for pressurizing consoles
CB-500A
7U centrifugal 500 cfm blower for pressurizing consoles, computers and electronic systems with cool, filtered air. Includes easy-to-remove, washable dust filter, 3-conductor AC cord and removable, brushed aluminum grille. Installs on 19” panel mounting rails.
-
product
Large Diaphragm Differential Pressure Switch
1630
Our highest precision conventional large diaphragm pressure switch provides maximum dependability. In addition, it incorporates a visible set point indicator for maximum convenience. UL and CSA listed, FM approved for general service, these switches are suitable for most applications in air conditioning and industrial service.
-
product
Millimeter Wave Antenna Testing
If you are involved in antenna or system level design using mmWave or THz frequencies, then you understand the importance of dependable testing equipment. It may be that you are designing passive phase array or that you are designing a mmWave radar sensor system, but when it comes to validation of your design, simulation can only bring you so far. Phased array antennas have to be measured over the air (OTA) to ensure the radiation pattern of your design efficiently conducts energy in the right direction which is where the MilliBox comes in.
-
product
Omnidirectional Hotwire Probe
AP3203
Omnidirectional hotwire probe with cable for Thermal Comfort measurements. Measuring range: air speed 0.02...5 m/s, temperature 0...+80 °C.
-
product
Filler Panels & Accessories
VadaTech offers a range of air baffles and filler panels for MicroTCA systems, including an innovative filler panel for single or double module slots that allows you to control the angle of the airflow baffle depending on your airflow analysis.
-
product
Electromagnet
The electromagnet can generate strong magnetic fields for experimental applications. Depending on the required magnetic flux density and Equipment under test volume the air gap can be adjustedcontinuously. The magnet poles come with conical shape close to the test volume to improve accessability and to optimize the achievable magnetic flux density.
-
product
Universal Measuring Device For Magnetic Fields
Teslameter M-Test MK4
The M-Test MK4 precisely detects and measures static or dynamic magnetic fields. The ~ 1 mm thick tangential probe allows precise, punctual measurements in hard-to-reach places, air gaps or on surfaces. The M-Test MK4 is particularly suitable for measuring permanent magnets or small ferromagnetic parts.
-
product
LGA 1200 Intel® Xeon® W & 10th Gen. Core™ ATX Server Board with 4 x DDR4, 5 x PCIe, 2 x PCI, 6 x USB 3.2, 5 x SATA 3, Quad/Dual LANs, and IPMI
ASMB-787
- LGA 1200 Intel® Xeon® W & 10th Gen. Core™ i9/i7/i5/i3 processors with W480E chipset- DDR4 2933/2666/2400 MHz ECC/Non-ECC UDIMM up to 128 GB- One PCIe x16 link (or two x8 link), two PCIe x4, and one PCIe x1 slots- Triple displays - DVI-D, VGA, and HDMI 2.0 ports- Five SATA 3 ports and six USB 3.2 ports- One M.2 2280/2242 (SATA / PCIe compatible)- Rackmount optimized placement with positive air flow design- 0 ~ 60 °C (32 ~ 140 °F) ambient operating temperature range
-
product
Environmental Testers
Our range of environmental test equipment provide users to test and measure all aspects of the environment. The comprehensive range includes temperature, infra red, sound level, humidity, LUX level and air flow.
-
product
Thermal Testing And Analysis
Response Dynamics Vibration Engineering, Inc.
We have consulted on thermal issues ranging from conduction issues in TECs, thermal radiation modeling, and countless air cooled system issues relating to system performance, vibration, and acoustics noise. We use a wide array of thermocouple instrumentation, thermal imaging, flow measurements, as well as finite element analysis and analytic modeling to measure, design, and debug thermal and related issues. We often work on customer products in our Response Dynamics lab where we characterize the system, engineer solution options, and prototype solutions. We then work with the customer to work the winning solution into their quality control and manufacturing process.
-
product
Dedicated Analyzer
This measuring instrument automatically measures gas volume / internal gas pressure, air content and oxygen concentration for quality control in the bottling process of carbonated drinks, etc.
-
product
Volume Checker
Gocator
For Volume Gauging of Cylinder Heads and Piston Bowls in Small to Medium-Sized Internal Combustion Engines. Gocator snapshot sensor w/ custom measurement tools. 3D non-contact measurement. Replaces traditional optical methods such as fluids, pressurized air, acoustics. Easily handles shape variation. Stereo camera minimizes occlusions.
-
product
(two/three-zone) Thermal Shock Chambers
TSA Series
Traditional three zone thermal shock chambers can be quite large, as three separate chambers are used. The TSA series has just one chamber, substantially reducing its size. Instead, it circulates cold, hot, or ambient air as needed. The conditioned air can be pre-cooled or pre-heated beyond the setpoint, allowing quicker recovery of the desired condition after transfer.
-
product
Dual Vapor Gravimetric Sorption Analyzer
DVS Resolution
DVS Resolution’s key feature is the combined ability to precisely control and measure temperature and relative humidity while recording the highest resolution changes in mass. DVS Resolution uses a dry carrier gas typically nitrogen or compressed air for its operation. Digital mass flow controllers regulate flows of dry and saturated gases. Relative humidity is generated by precisely mixing dry and saturated gas flows in desired flow ratios which produce expected relative humidity. In a typical experiment a known concentration of water vapor is delivered over a sample placed inside the sample pan connected to the Surface Measurement Systems Ultrabalance™ measuring realtime mass changes caused by sorption or desorption of water molecules. Prior to sorption measurements, the sample can be in-situ preheated/dried at temperatures of up to 300oC.





























