Field Of View
-
Product
Relative RF Field Strength Meter
7601
-
Coaxial Dynamics Model 7601 Relative Field Strength Meter is used for measuring the relative strengths of radiating fields of patterns from a transmitting antenna system, making relative RF power measurements, or peaking and adjusting fixed or portable transceivers and antennas
-
Product
Ruggedized Field Deployable Fiber Transport
Field Fiber Series
-
It’s a tough world out there. Whether onboard a truck, inside a sports venue or outside in the open air, our customers consistently work in harsh, high-pressure production environments. The rigors of long-distance road transport and inclement weather will not excuse failure during live sports, events and broadcast news production. They also must contend with signal counts and connectivity requirements that change with each event. MultiDyne is trusted worldwide for durable, flexible, battery-powered field fiber systems that users can safely transport between events and confidently deploy with broadcast quality signal I/O. With solutions for productions of any scale, including ultra-compact throwdown devices, rackmount units and fully configurable, high-density portable systems, MultiDyne’s field fiber solutions optimize reliability for any short-haul and long-distance field application.
-
Product
Rotation Field Testers
-
PeakTech Prüf- und Messtechnik GmbH
Direction indicators are indispensable for use in the electrical assembly of three-phase motors. In normal use, the test leads are connected to the live terminals, with an R / L display showing the later direction of rotation of the electric motor. In addition, this model can be used for the contactless determination of the direction of rotation of switched-off or not connected motors. Place the switched-on measuring device on the motor parallel to the longitudinal axis without test leads. Now turn the shaft of the motor, the measuring device now shows a right or left movement.
-
Product
On-Site Field Testing & Evaluation
-
MET is a highly-regarded resource for electrical inspection agencies within the United States and Canada to assure compliance of unlabeled equipment in the field. Field evaluations are performed by MET Laboratories on unlisted equipment to support the Authority Having Jurisdiction.
-
Product
Flat Field and Imaging Gratings - Type IV
-
HORIBA Scientific produces a wide range of holographic master gratings from which high precision replicas are manufactured.Type IV aberration-corrected flat field and imaging gratings are designed to focus a spectrum onto a plane surface, making them ideal for use with linear or 2-D array detectors.These gratings are produced with grooves that are neither equis-paced nor parallel, and are computer optimized to form near-perfect images of the entrance slit on the detector plane.
-
Product
Ethernet Field Modules
-
- Reliable transmission of machine data, process parameters and diagnostic data to the controller- Simultaneous data exchange with the controller and the IT world- Wide operating temperature range and high protection rating- Robust housing with high protection rating
-
Product
Field Test Interface Kit
2200
-
TESCO’s new Field Test Interface Kit (Catalog No. 2200) provides metering professionals with exceptional testing flexibility. The Field Test Interface includes a zero insertion force (ZIF) meter socket, voltage and form selection, and connection points to link it with a TESCO Field Test Kit (Catalog No. 621, 630 or GA Series). When combined with a Field Test Kit and powered via inverter (commonly used on service trucks), the Field Test Interface will then power the Field Test Kit to create a single position, stand-alone, meter accuracy testing device for various socket based meters (both mechanical & solid-state). Power for the Field Test Interface can also be supplied by customer potential via TESCO Field Test Kit (no need for the inverter).
-
Product
XCITE 1100 Field Test Series
-
The Xcite 1100 Field Test Series uses the same Exciter Heads and Master Controller as the 1100 Laboratory Series but replaces the 5 GPM 3-Phase Hydraulic Power Supply with a field portable 1.2 GPM Single Phase Power Supply. While providing the same 3000 PSI pressure, the field test unit is switch selectable from 110 V (20 A) to 220 V (10 A) single phase power.
-
Product
Field Test
-
Field test equipment is an optimised solution for large system testing, which, thanks to its distributed architecture, enables the placement of several small-sized testing systems.
-
Product
Digital Static Field Meter
Model 715B
-
- Assess electrostatic fields or charge on objects- Measures up to ±19.99 kV at a distance of 1 inch- Accuracy of <±5% in both normal and ionized environments- Uses a chopper stabilized sensor- LED ranging lights for positioning the meter at the right distance- Zero function allows the display to be adjusted to zero (0)- Hold feature to lock the reading on the display- Low battery indicator on the display- 1-year limited warranty
-
Product
Field Probe Positioner
-
The Field Probe Positioner FSM2315 is designed for the automation of the 16 point measurement, according to IEC/EN 61000-4-3. The system provides X and Y axis positions for continuous and step by step movement for the filed probe, 0.8m above the floor and with a 1.5m x 1.5m area, for the 16 sensor positions. A dismountable solution is available.
-
Product
Magnetic Field And Permeability Measurement
MAGNETOMAT 1.790
-
Foerster Instruments, Incorporated
The MAGNETOMAT 1.790 is a measuring system for the precision detection of magnetic flux density and relative permeability. The MAGNETOMAT software is used for displaying the measured values and saving and exporting data. The wide range of probes facilitates optimal adjustment to the conditions of the application, such as the measurement of relative permeability within the scope of the quality control of stainless steel and low-permeable (non-magnetic) alloys. Further applications include the long-term monitoring of the magnetic environment, e.g. prior to installing magnetically sensitive devices, and the localization of ferrite enclosures in stainless steel and NE materials. Changes in material (sulfidation, degradation of lamination, structural changes) can also be proven thanks to permeability comparative measurements.
-
Product
Three Channel AC Magnetic Field Signal Conditioner
TCM-1A
-
Macintyre Electronic Design Associa
The TCM-1 is a three-channel portable signal conditioner specifically tailored to provide power to and process the signals from MEDA's line of AC magnetic field sensors. The unit operates from either its internal batteries or the power line. It incorporates two sets of power line rejection filters, switch selectable for 50 or 60 Hz and the corresponding first four harmonics.
-
Product
Field Calibrator of Three Phase Energy Meter
SY3640
-
Hong Kong Songyang Industrial Ltd.
SY3640 three phase energy meter field calibrator is a high precious three phase energy reference meter; it uses the advanced technology and latest electronic components available in the world, and use high speed DSP as the main processor to ensure the accuracy and long time stability.
-
Product
Single Axis AC Magnetic Field Sensor
MGC-1A
-
Macintyre Electronic Design Associa
The MGC-1A is a low noise high sensitivity single axis AC magnetic field sensor used for the measurement of audio frequency fields. Because of its innovative design, the MGC-1A amplitude response is insensitive to the frequency of the field over its 30 Hz to 10 kHz frequency band. Accuracy at 1 kHz is ±1%, and the amplitude response stays within 2 dB peak-to-peak over the bandwidth.
-
Product
Near Field Probes 30 MHz up to 3 GHz
RF1 set
-
The RF1 near field probe set consists of 4 passive near field probes for making measurements in the development phase of E-field and magnetic field in the ranges of 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF1 set allow for measurements close to the electronic assemblies, e.g. on single IC pins, conducting paths, components and their connectors in order to localize interference sources. Field orientation and field distribution on an electronic assembly can be detected through a trained special use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance.
-
Product
Magnetic Field Measurement Systems
-
The magnetic field probe performs non-contact current measurements and can be used for real traces. The probe of higher resolution enables pinpoint measurements.
-
Product
Probes, Magnetic Field
EM-6881 | 480 KHz To 30 MHz
-
The EM-6880, EM-6881 and EM-6882 Magnetic Field Probes operate in conjunction with any 50 ohm input impedance receivers.
-
Product
EMF Fluxgate Magnetic Field Meter
LM-MP6000-EMF
-
The List-Magnetik LM-MP6000-EMF EMF fluxgate magnetic field meter (fluxgate magnetometer) can measure very weak DC and AC magnetic fields in the range of 0–400 µT (microtesla), 0–4 G (gauss), or 0–300 A/m. The device uses a fluxgate measuring probe to measure magnetic fields in the transverse direction.
-
Product
Controlled Impedance Field Solver
Si8000m
-
TheSi8000m is an all new boundary element method field solver , which builds on the familiar easy to use user interface in earlier Polar impedance design systems. The Si8000m adds enhanced modeling to predict the finished impedance of multiple dielectric PCB builds and also takes into account the local variations in dielectric constant on close spaced differential structures.
-
Product
Field Ttesters
-
Our product range comprises from small handheld, battery fed testers to full featured service performance assurance tools and distributed monitoring systems. We have several product lines including:QoS / SLA verification system Ethernet, IP, Critical Data, VoIP, IPTV .Hand-held testers: Gigabit Ethernet, Synchronous Ethernet, E1, PDH, SDH, Ethernet, IP, Jitter, Wander, Datacom, Frame Relay, etc.
-
Product
Electrostatic Field Meter Kit
PFK-100B
-
- Measure range & polarity of electrostatic fields in 1 volt or 10 volts increments- Charges from zero to over 1000 volts in less than 5 seconds- Balance Ionizers per ANSI/ESD SP3.3 Periodic Verification- Measure Ionizer Decay time as per ANSI/ESD S3.1 and ANSI/ESD SP3.3.- Measure Body Voltage Generation and Decay- Use with a datalogger to record measurements & create reports- Compatible with the Autoanalysis System- Accuracy of ± 5%- Battery Operated
-
Product
Measuring Solar Fields
ISET Sensor
-
The solar radiation sensor is characterized by a simple and compact but precise structure. Use in balancing monitoring systems for simple, fast and reliable information about the functioning and solar "energy yield" of a PV plant. For site surveys, monitoring and other fields of survey technology.
-
Product
Vector Field and Multi-Axis Systems
-
Cryogenic vector magnet systems allow precise alignment of the magnetic field to an exact direction in a measurement sample. The system provides the capability of orienting the magnetic field to any vector direction. This is suitable for experiments where samples cannot be moved easily.
-
Product
Near Field Probes
-
Anteral has extensive background in the design of Near Field Probes (open ended waveguides probes). Our Near Field Probes are currently being used in several laboratories around the world including the ESA's anechoic chamber. Anteral designs Near Field Probes from 10 GHz to 750 GHz covering the sectors requirements. Moreover, our Near Field Probes have a sharped design minimize reflections.
-
Product
Scanning Near Field Optical Microscope
SNOM
-
SNOM microscopes employ SPMs precision of piezoelectric raster-scanning together with sharp probes to obtain light optical images at rather better than the usual wavelength-limited resolution. The possibility to go beyond the Abbe diffraction limit has been achieved with the Near-field light optical microscopes (SNOM or NSOM).
-
Product
Electro Field Meter
-
Electrostatic discharge is now a problem in many workstations, as modern microelectronics (integrated devices) are susceptible to damage caused by electrostatic discharge. However, other industries, such as telecommunications, plastics and explosive industries, are also severely affected.
-
Product
Magnetic Field and Permeability Measurement
MAGNETOSCOP® 1.070
-
Foerster Instruments, Incorporated
The MAGNETOSCOP 1.070 is a portable magnetometer system with microprocessor and probes for measuring the magnetic flux density as an absolute or differential value (gradient). It has a USB port for simple data transfer and an SD card for saving measurement data and parameters. The measuring system also facilitates the recognition and saving of peak values and the adjustment of thresholds for limit values. The unit can be used for series and individual measurements. The data can be easily analyzed and documented with the PC software included in the scope of delivery. The MAGNETOSCOP 1.070 thus facilitates the portable and fast measurement of the relative permeability within the scope of the quality control of stainless steel and low-permeable (non-magnetic) alloys as well as the localization of ferrite enclosures. Changes in material (sulfidation, degradation of lamination, structural changes) can also be proven thanks to permeability comparative measurements.
-
Product
Free DR and High Field Magnet in Shared Vacuum Space
-
50 mm 4 K magnet bore, 30 mm sample space in DRSuitable for use with Leiden DR type CF200, CF450, CF650 or CF1000 DR
-
Product
Power Frequency Magnetic Field Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
Power frequency magnetic field simulator is a special designed instrument with high reliability according to the features of the power frequency magnetic field immunity test for electrical and electronic products.
