Validators
Assure standards are met.
-
Product
UVC Light Meters & Detectors
-
International Light Technologies
If you are using a UVC light-based disinfection system you are probably scrambling to deploy tools to combat the COVID-19 outbreak. Increasingly facilities are looking to disinfect everything including air, surfaces, instruments, and personal protective equipment (PPE) using UV-C light. Verifying the intensity of the light, or dose, reaching the target is a critical step in validating that the correct UV dose is being applied to ensure proper decontamination.
-
Product
AWG
-
With the accelerated growth of hyperscale datacenters, Ethernet network infrastructure performance demands are increasing exponentially, and customer expectations for high-speed data throughput are at an all-time high.Other high-speed I/O protocols such as PCIe Gen 5 and 6 are also gaining momentum. Arbitrary Waveform Generators are the ideal general-purpose development tool for validating high-speed receivers and are extremely flexible instruments for coherent module development.
-
Product
PXI Semiconductor/IC Test System
Test System
A high-density 100MHz PXIe digital IO card designed for characterizing, validating, and testing a variety of digital and mixed-signal ICs. Each IO card consists of a Sequencer Pattern Generator (SQPG) and 32 channels of full ATE-like features. The 33010 IO card is expandable up to 256 channels. Some unique features of the 33010 include an on-board SQPG, per pin timing/levels/ PMU/TFMU, multiple time domains, and multithreaded testing for complex IC testing. Each channel is also equipped with 64M vector memory, 16 timing sets with on-the-fly timing change, and per pin timing and frequency measurements up to 400 MHz.
-
Product
Insight Pharmaceutical Metal Detection System
-
The Insight PH Pharmaceutical Metal Detector is designed for inspecting tablets and capsules after the tablet and de-duster process with throughput of up to 30,000 units per minute. The system is built with a gas strut stand frame offering exceptional manoeuvrability making it convenient for use with all leading tablet presses and encapsulation machines.Designed with throughput of up to 30,000 units per minute, the Insight PH comes complete with full IQ, OQ & PQ validation documents and certification.
-
Product
NVMe-oF
-
NVMe/oF adoption is rapidly increasing and full NVMe specification conformance over Ethernet networks or Fibre Channel fabrics requires the ability to validate transactions over all transports.
-
Product
Calabash
-
In short, Calabash is a test automation framework that enables mobile developers and pretty much anyone without coding skills to create and execute automated acceptance tests for Android and iOS apps. Calabash works by enabling automatic UI interactions within an application such as pressing buttons, inputting text, validating responses, etc. While this is a great first step in automated UI acceptance test automation, the real benefits can be gained when Calabash tests are executed on real mobile devices. This is very easy and Calabash tests can be configured to run on hundreds of different Android and iOS devices, providing real-time feedback and validation across many different form factors, OS versions, OEM customizations and hardware specs.
-
Product
SpaceWire Recorder
317
-
The SpaceWire Recorder is designed to support the validation and debugging of complete SpaceWire systems. Using the advanced SpaceWire technology from STAR-Dundee Ltd and the very latest solid state data storage technology the SpaceWire Recorder offers exceptional SpaceWire recording capabilities.
-
Product
Universal Software-Defined Radio
VPX3-E320
-
Curtiss-Wright Defense Solutions
Designed for superior durability and reliability, the VPX3-E320 incorporates Curtiss-Wright’s industry-leading rugged hardware design and validation practices to meet the stringent requirements of the most demanding front-line environments. Paired with the industry-leading UHD based software-defined radio workflow, this product is truly unique.
-
Product
Electrical DfT & Fault Coverage Analyzer
TestWay
-
TestWay's electrical DfT analyzer enables designers to validate designs at the schematic capture stage, to ensure that adequate measures have been included to comply with the manufacturers test requirements. The ability to verify that PCB designs have been developed with adequate Design-for-Test in mind, is key in determining the most effective test strategies and accurately calculating fault coverage, which is crucial in improving competitive advantage, lowering cost and ensuring product quality.
-
Product
Validation System
FLEX BMS
System
The FLEX BMS™ Validation System is a quick-connecting, highly flexible test system for rapid evaluation of centralized, single-board and distributed battery management systems. Utilizing Bloomy’s industry-leading battery cell simulators, COTS instrumentation, industry-standard connectors, and models that run in real-time, the FLEX BMS™ Validation System can easily be reconfigured to test a wide variety of BMSs. The FLEX BMS™ Validation System is used by national and regional safety and standards labs for certifying the BMS for a wide array of e-mobility products and applications.
-
Product
V2X Test Tools
-
Validate and verify your V2X application with our Mx-Drive Mobility Simulator. Use the Mx-DSRC Compliance tester for USDOT certification.
-
Product
Clamp Meter, True RMS, 100 A AC, 600 V AC, 600 V DC, 17 mm Jaw Opening Max.
72-2985
-
The 72-2985 from Tenma is a mini clamp meter in orange and grey colour. It features high reliability, safety precision and compact design. Its resolution ratio is 1mA, maximum range has maximum range of 100A AC/DC, particular VFC start mode. Entering this mode can accurately measure voltage and current which has VFC frequency conversion. Voltage or current response display is true valid value. Whole range overload protection, reliable measurement accuracy and unique appearance design makes it an outstanding new generation functional electrician/electric power measurement instrument. This complies with EN 610101-1, 61010-2-032, 61010-2-033, pollution degree 2, measurement category: (CAT II 600V, CAT III 300V) and double insulation standards. Conforms to UL STD. 61010-1, 61010-2-032, 61010-2-33 certified to CSA STD. C22.2 NO. 61010-1, IEC STD 61010-2-032, 61010-2-033.
-
Product
Fixture Interface Module 2 Test Matrices
OTP2 module no.193
Interface Module
PXI offers the optimal approach to validation and production testing. You can meet timing, synchronization, and throughput requirements across devices. PXI is a robust PC-based platform for measurement and automation systems, supported by software. PXI combines PCI electrical bus characteristics with CompactPCI's modular Eurocard packaging, and then adds special synchronization buses and important software functions. PXI is both a powerful and cost-effective platform for applications such as manufacturing test, military, aerospace, machine monitoring, automotive, and industrial test.
-
Product
Detective Logic Analyzer
DDR3
-
Provides logic analyzer like deep transaction Listing and Waveform captureCan store up to 1G of captured StatesContinuous, real time analysis, not post-processingEye Detector guarantees valid data acquisitionExtensive Triggering and Storage Qualification allows precise insightProtocol Violation Detector provides hundreds of simultaneous, real time tests to JEDEC specificationsRow Hammer Analysis for potential data corruptionInteractions among up to 8 ranks, over two slots are analyzed.Mode Register Listing providedSupports Auto-Clock rate detect and clock stoppage Connects to the target under test with DIMM, SO-DIMM, and BGA interposers or a midbus probeIntegrated Microsoft Charts gives quick insight into large trace capturesTrigger In & Out allows the Detective to integrate with other test tools
-
Product
DH Series QuickLink Adapter Kit with 3 x QL-SI Tips
DH-QL-3SI
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
Au Truck / Bus Fleet Management System (FMS) Simulators
-
The Au Truck / Bus Fleet Management System (FMS) simulator can generate Controller Area Network (CAN) signal per Truck FMS Standard (Vers. 02.00) and Bus FMS Standard (Vers. 00.02). Au FMS simulators are designed very easy to use. All editions can run independently (without personal computer). Au FMS Simulators are widely used as valuable tools for any situation from product-line test, incoming inspection, business demonstration, to product development and product validation.
-
Product
Antennas
-
The PLA-R and PLA-T are active, battery powered receive and transmit loop antennas for the frequency range 9 kHz - 30 MHz intended for radiated emission testing (PLA-R) and site validation: Normalized site Attenuation, Shielding Effectiveness (PLA-SET consisting of PLA-R and PLA-T)
-
Product
Mezzanine System
5047
System
The 5047 provides breakout of all ECM signals for debug, design validation and development. Plated through holes on the PCB allow soldering of probe wires to IO, Data, Power and Serial Identification signals. LEDs indicate presence of 3V, 5V, +12V, -12V and Ground. Elevates the ECM module by 2 mm and saves wear on the ECM carrier board connectors. Since this is a debug too there is no serial identification circuit.
-
Product
Inductively Coupled Plasma Mass Spectrometer
ICPMS-2030
-
With its newly developed collision cell and optimized internal structure, the ICPMS-2030 provides superior sensitivity. At the same time, thanks to the adoption of its proprietary mini-torch unit and provision of an Eco mode, the quantity of argon gas needed for analyses has been greatly reduced to the industry's lowest levels. As a result, low running costs are assured. The Development Assistant function of the software automatically sets the optimal analysis conditions for quantitative analysis. Then, after measurements are complete, the Diagnosis Assistant function automatically checks the validity of the necessary data. While reducing the burden on the user, the efficiency of analyses is enhanced and the reliability of the data can be increased. It complies with FDA 21 CFR Part 11.
-
Product
Datapaq Food Tracker System
-
Designed to measure and log true product and environmental temperatures and to deliver reliable, accurate HACCP process validation, the Datapaq Food Tracker System is the ideal solution for demanding food processing applications. The system is particularly suited to poultry, meat and seafood processing; commercial baking; frozen food production; commercial pasteurization and sterilization; and proving your compliance with HACCP regulations.
-
Product
ProxiLAB Quest Contactless Tester
-
Fully programmable card (PICC), reader (PCD) and NFC signal emulator for device characterization and protocol conformance verification. ProxiLAB Quest offers the performance and features required for full characterization and conformance validation of all 13.56 MHz contactless technologies, including the latest very high bit-rate evolutions. ProxiLAB Quest integrates with a variety of conformance certification solutions and test automation platforms.
-
Product
OSFP 800G
-
OSFP800 has emerged as a leading standard to drive the development of 800G ecosystem. The MultiLane OSFP800 development kit is an essential tool to ensure the validity of your OSFP800 products. The module compliance board (MCB) is used to test transceivers, AOCs, active cables and DACs, while the host compliance board (HCB) enables the testing of system host ports. The loopback modules (LB) provide an economical way to test thermal capacity and signal integrity of system host ports at every stage of the process: R&D validation, production testing, and field testing.
-
Product
Antenna Test Chamber for Automotive Radar
ATS1500C
-
The R&S®ATS1500C radar test chamber is a compact antenna test range (CATR), consisting of a gold-plated parabolic reflector and a two-axis positioner for 3D movements of the radar module. Combined with the R&S®AREG800A target simulator and other Rohde & Schwarz test and measuring instruments, it can be used for a variety of applications, including antenna characterization, module calibration, RF performance validation, interference testing or in-band compliance testing. The chamber is equipped with a universal feed antenna which gives access to both polarizations in parallel. Automated temperature testing over the range of -40 to 85°C is possible with an optional enclosure.
-
Product
ICT Tester
-
Adapter design, assembly and validation for Agilent, Keysight, HP, Checksum, Spea. Preparing and debugging ICT scripts. ISP Programming Integration. Integration of edge scan testing, Jest testing, digital testing, semi-functional testing, IC programming, FINN probes, and more
-
Product
Accelerated Mobile Pages (AMP) Testing Tool
-
Accelerated Mobile Pages (AMP) is a great way to make content on your website accessible in an extremely fast way. To help ensure that your AMP implementation is working as expected , Search Console now has an enhanced AMP testing tool. This testing tool is mobile-friendly and uses Google's live web-search infrastructure to analyze the AMP page with the real Googlebot. The tool tests the validity of the AMP markup as well as any structured data on the page. If issues are found, click on them to see details, and to have the line in the source-code highlighted. For valid AMP pages, we may also provide a link to a live preview of how this page may appear in Google's search results.
-
Product
Millimeter Wave Antenna Testing
-
If you are involved in antenna or system level design using mmWave or THz frequencies, then you understand the importance of dependable testing equipment. It may be that you are designing passive phase array or that you are designing a mmWave radar sensor system, but when it comes to validation of your design, simulation can only bring you so far. Phased array antennas have to be measured over the air (OTA) to ensure the radiation pattern of your design efficiently conducts energy in the right direction which is where the MilliBox comes in.
-
Product
Diagnostic Test System™
-
The original Teseda system for bench-top stimulus, test pattern debug, validation, device failure mode stimulation in-situ with other Failure Analysis lab equipment such as an EMMI, etc.
-
Product
Validation, Mapping and other Services for GxP Regulated Applications
-
The individuality of your GxP application may require a variety of function-specific settings and measurement systems. Benefit from our know-how and let our application engineers design the optimal measuring system for you. With our consulting services in GxP, we support you from project planning (URS) to implementation and testing of your system. This ensures an optimal and efficient design.
-
Product
Compiler Test & Validation Suite
SuperTest
-
SuperTest is the test and validation suite for C and C++ compilers that has tracked the (ISO) language specifications for more than 30 years. It is a complete validation environment with: A huge library of hand-written test, A large body of generated tests, A framework to easily set-up and run compiler validations.
-
Product
Load Simulator
Simulator
The load system is intended for testing satellite power supply systems; due to the integration with a solar array simulator and a battery simulator, it can perform validation and commissioning of satellite power supplies. The system is equipped with regenerative electronic loads and customer-specific high-power switching matrices for routing the DUT channels to the relevant loads. The individual voltages and currents for each channel can be read back via a Keysight Technologies switch mainframe.The system is equipped with high electrical power; its loads are capable of feeding the energy back into the power grid.
