Cable Locators
detect an induced or directly transmitted signal through a cable to trace its location.
-
-
product
xDSL Line Qualifier
ELQ 2+
2,2 MHz Test Set for the qualification of ADSL & SHDSL lineswith data rate calculation. TDR & Bridge for cable fault location.
-
product
Underground Cable Fault Locator
KM-CFPL-620 /620B
Kusam Electrical Industries Limited
“KUSAM-MECO” underground Cable Fault Pre-locator is an automatic Cable Fault Locator which adopts ARM, FPGA & Dot Matrix Color LCD display Technology. This tester combines both pulse reflecting technology (TDR) & (intelligent Bridge testing (Bridge) (Model-KM-CFPL-620B) for measuring the exact fault location such as broken line, cross faults, earthing, (poor insulation & poor contact of the lead covered cables as well as plastic cables. (Model-KM-CFPL-620B)).It is a microprocessor based fault locator with a user friendly menu. It is easy to operate. It tests almost all telecom & signal cables. It has an English menu which is easy to understand & use. With Megameter & Ohmmeter it enables to test insulation resistance & loop resistance. It has USB Port for uploading test data to computer
-
product
Pipeline & Cable Locator
Fuji Pipe & Cable locator assists you with its high performance on the engineering work site in locating the underground utilities such as the Metallic Water lines, Gas lines, tracer wire by plastic pipe, telephone/TV cables, copper and aluminum wire, conduit and power lines. This is the result of an evolution from the original FUJI TECOM Pipe & Cable Locator manufactured in 1967.The Differential antenna, which minimizes the influences of inductive fields and thus facilitates the accurate location of utility lines.
-
product
LAN Tester
TVR10/10/100
Triplett Test Equipment & Tools
TVR10/100/1000 LAN Tester is comprised of a "Main unit" and a "Remote Probe". The Main unit performs the bulk of the tests, such as determining the LAN device type (is it a hub/switch or PC?), the LAN speed and duplex (10, 100, 1000 MB/s, half or full duplex) and whether PoE (Power over Ethernet) is present without the need of the Remote Probe. The Remote Probe adds the ability to trace cable locations (by audibly tracing tones placed on the cable by the Main Unit) and to test the wiring of the cable (by decoding and displaying wiring information placed on the cable by the Main Unit).
-
product
Cable Test Van
BAUR Transcable 4000/S 32-3
BAUR Prüf- und Messtechnik GmbH
Transcable 4000/S 32-3. Thetranscable 4000/S 32-3 cable test van is a 32 kV cable fault location system in 3-phase version. The system is controlled with the MGS semi-automatic control unit. The high voltage switch unit is maintenance-free and fully safe to touch.
-
product
Miscellaneous Testing Equipment
Technology Products offers a complete range of Cable Fault Locating Equipment for LV & HV Cables in Power Plants, Heavy Industry & Distribution Systems . Occurrence of cable fault can not be avoided due to many factors. Long outage of a cable from service results in heavy loss of revenue to the power distribution company, production loss to industries as well as unpleasant condition to general public. This requires an efficient instrument capable of locating the fault in minimum possible time and restoring the supply.
-
product
Universal Locator
UL 30
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR UL 30. The UL 30 receiver is used together with a ground microphone (BM 30) and a surge voltage generator (SSG, STG) to pinpoint cable faults. With the coil integrated in the BM 30 for runtime measurement, the device determines the time difference between the magnetic and acoustic signal. This particularly offers special advantages when d ealing with faults difficult to locate acoustically.* Built-in speaker* Splashproof design* Large, illuminated display* Lightweight
-
product
Cable Test Van
Titron
BAUR Prüf- und Messtechnik GmbH
Automatic cable test van. The BAUR titron is a new automatic cable test van designed for cable fault location and cable testing. The new generation of the high-performance cable test van is based on state-of-the-art technology and provides effi cient, safe and reliable cable fault location and cable testing.* New intuitive operational concept* Central, automatic system control* Top reliability and quality standard* Flexible in terms of technology and equipment
-
product
DVI Extender via Two Singlemode/Multimode Fiber Optic Cable up to 4,920 Feet
ST-2FODVI-LC
The XTENDEX® DVI Extender via Fiber Optic Cable locates a single link digital DVI display away from a computer up to 4,920 feet using singlemode fiber optic cable and 1,640 feet using multimode fiber optic cable. Supports resolutions to 1920x1200.
-
product
Cable Detectors
With certain models of cable detectors you can locate open power cables, either live or dead (without current), with voltages up to 300V. Cable detectors can locate cables, circuits, short circuits and ground points. To perform these functions, it is not necessary to disconnect electrically sensitive devices or to disconnect theCable Detectors to locate open power cables, either live or without current, up to 300V power from the cable which is being tested. Cable detectors can also locate ferrous and non-ferrous metals, wood and plastic with a high level of accuracy.
-
product
Cable Locator (LCD type)
5500 CB
Standard Electric Works Co., Ltd
● The 5500 CB transmitter is a great tool for locating and identifying cables and individual conductors. ● Designed for locating unenergized cables and powered cables. ● Voltage measurement for cables : ACV 12V~300V DCV 12V~300V ● Signal Transmission • Transmission Power Level Selection (includes 1, 2, 3) • Transmission Signal Code Selection (includes F, E, H, d, L, C, O, A) ● Flashlight & Back Light function.● The Silent Mode (Disable Button Beep).● The Level Bar Display on the LCD Screen (the transmission power level indication).● The Action Wave Display on the LCD Screen (when the signal is transmitted).● Auto power off function.
-
product
Cable Tester
TESTER
Whirlwind Music Distributors, Inc.
This versatile cable tester checks many varieties of audio cables. It tests most cable combinations of XLR, 1/4" or RCA Phono plugs for shorts, opens, and polarity reverse. The handsfree design allows manipulation of the cable to locate intermittents.
-
product
Audio Frequency System
Locator Set / UL 30
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR Locator Set / UL 30. The audio frequency system Locator Set is used to exactly determine the alignment of cables and metal gas or water pipes. With various accessories, this system becomes a universal, indispensable device for power companies, industries, installation companies and water suppliers.* Output energy up to 50 VA* Automatic or manual impedance adjustment* Charging unit and rechargeable battery integrated; battery or mains operation* Continuous or cyclical output
-
product
Fault finder
The STaff™
The staff fault finder is designed to meet the demands of the professional troubleshooter but its simplicity and price make it a tool for anyone needing to locate cable faults. Arrows on the LCD screen direct the user to the fault with pinpoint accuracy. A reference indication also will aid the user in identifying multiple faults when present. Whether you are fault locating utility service line or locating a broken sprinkler wire, the STAFF is the professional's choice.
-
product
50-Watt Rack Mount Transmitter
FLS-2
Fiber optic cables are a critical part of modern life due to the vast amount of data they carry to support businesses, internet users, and emergency services. The cost of losing these services, even temporarily, is immeasurable. The FLS-2 system is designed to assist in locating, monitoring and providing damage prevention to these cables. The FLS-2 high-performance, high-power rack-mounted transmitter is typically mounted in a re-gen staton, customer access point, or central office. The FLS-2 transmits a locate tone on the metallic sheath of the fiber cable over vast distances to ensure the cable can be located quickly and accurately, even in congested areas.
-
product
Surge Voltage Generator
SSG 500
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR SSG 500. The SSG 500 surge voltage generator is arranged in a 19'' housing. Maximum safety is achieved with the electrical safety control unit, the automatic discharge unit, the fully enclosed design and separate protection and system earth.* 6 output voltages up to max. 16 kV available* Electromagnetically actuated surge switch* Preselectable surge energy: 288 / 512 Ws (in all voltage ranges)* Automatic discharge unit
-
product
Power Cable Fault Locator
TM500
TM500 Power Cable Fault Locator adopts international advanced electronic testing technologies and SCM technology, and combines low-voltage pulse reflection and pulse current testing methods, is suitable for the precise range finding of power cable high resistance, flashover, disconnection, and low resistance. Low-voltage pulse reflection method applies to test the range of the low resistance and broken line, and the length and wave velocity of various cables. Pulse current testing method can be divided into breakthrough high-voltage flashover and DC high-voltage flashover for the high resistance and flashover cable fault finding.
-
product
Cable Test Van
BAUR Transcable 4000/S 110-1
BAUR Prüf- und Messtechnik GmbH
Transcable 4000/S 110-1. The transcable 4000/S 110-1 cable test van is a 110 kV cable fault location system in single-phase version. The system is actuated with the semi-automatic MGS control unit. The high voltage switch unit is single-phase, up to 32 kV, the 110 kV switching level is designed as air-insulated ceiling switch.
-
product
Precision Cable Locator Range
Radiodetection’s precision locators are designed for optimal locate performance for damage prevention professionals working in all industries and utilities.
-
product
Time-Domain Reflectometer
TDR-410
*Location damaged power cables.*Fault location copper telecom cables.*Coaxial cable fault location.*Fault location wiring infrastructure.*Detection of breaks, short circuits, damage caused by dampness and other changes in impedance of the cable.*Graphic depiction of damage the cable with automatic indication the distance to fault on the screen.
-
product
MARK V “Ranger”
Mk V
Radio and audio frequencyInductive or conductive operationOn handle to find unknown structuresInterrupter feature on transmitterVery accurate depth location (triangulation)RF Pipe & Cable locator (Short Locator)Holiday detection of buried pipe (Pearson Method)Volume controlBattery operatedRechargeable NiCad batteries available (optional)
-
product
LAN Testers
A cable detector can locate open power cables, either live or without current, up to 300 V. A cable detector can locate cables, circuits, short circuits and ground wires. To perform these functions, it is not always necessary to disconnect electrically sensitive devices or to disconnect the power to the cable being tested.Many cable detector devices can also locate ferrous and non-ferrous metals, wood and plastic with high degrees of accuracy. A cable detector provides a safe way to test wall sockets for which no electrical plans or wiring information is available about the cables or their output. A cable detector is very versatile, as it ensures speed and safety when making holes in walls, ceilings and floors.
-
product
Cable Locating Device
TM520
Coordinating with high-voltage signal generator, test sound and magnet simultaneously, locate high-resistance and arc-over fault of the power cable. While fixing the fault point, the instrument can test the cable path as well.Coordinating with audio-frequency signal generator, test audio frequency induction, locate low-resistance fault, and identify the cable and test the depth of it.
-
product
Time Domain Reflectometer
IRG 2000
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR IRG 2000. The IRG 2000 impulse reflection measurement unit or time domain reflectometer is a handy, easy to carry device for single-phase cable fault pre-location. It is used in combination with a surge voltage generator on low-, medium- and high-voltage cables 0 - 65 km in length. It can also be used on live cables carrying voltage up to 400 V.* Easy and quick cable fault location* Light, compact and manageable* Main unit for the tried-and-tested pre-location method* Ideal for integration in measurement systems
-
product
NEXTest 7
PK-2030/2032/2033/2036/2037/2038
NEXTest 7 is an advanced and unique tester in the market. It's designed to check and troubleshoot the pin connections of Display port & HDMI prior to installation on equipment. By using advanced technology to verify the integrity (20 pins + shield) of both display port and HDMI cables, especially for HDTV installation and DIY termination in the field, solving your cable testing need, unlink all of the other testers verify 9 circuits only. It checks for opens, shorts, miswires and intermittent faults in all conductors plus shield continuity, most tester only test for opens. It displays cable map results of both TX (near end) and RX (far end) on the main unit, either on testing before or after installation cables. User can easily read and determine the actual 21 pins configuration on main unit. It employs both auto and manual scanning of 21 wires. Tone Generator mode transmits two selectable tones on each pin for use with Net Probe (PR-06P) optional, enables one to quickly locate a cable. It's capable of testing up to 8 cables and locations at one time. NEXTest 7 especially features a self-learning mode to memorize cable pin out for testing large quantity standard or custom cables for PASS/FAIL a snap, makes testing quick and more efficient.
-
product
Search Receiver
KMF 1
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR KMF 1. The KMF 1 search receiver is used according to the step voltage method. The cable line is scanned with two measurement probes that can be dismantled during transport. The battery-operated device is also suitable for locating multiple consecutive sheath faults.* Battery mode* Zero point compensation* accurate location of cable sheath faults* battery test
-
product
Cable Fault Location System
Syscompact 2000 M Pro
BAUR Prüf- und Messtechnik GmbH
Cable fault location system 2000 M pro. The portable BAUR Syscompact 2000 M pro cable fault location system is used for cable fault location and cable testing in low- and medium-voltage cables up to 65 km length.* Fully integrated proven cable fault pre-location methods* Surge mode for acoustic pin-pointing* Easily transportable* Ideal for locations that are difficult to access
-
product
CATV Meters & Instruments
GAOTek offers high quality, affordable CATV meters and testers to industry engineers. These instruments are used by professionals to automatically or manually test, measure, and maintain a wide collection of systems and channels. Our products are portable and durable to ensure long operational use during everyday field use by CATV technicians. Additionally, we offer QAM analyzers, PCM channel analyzers and TDR cable fault locators.
-
product
Cable Fault Locator
TW3304N
Techwin(China) Industry Co., Ltd
The Perfect Handhold Tester Series Cable Fault Locator TW3304N is the most portable test instrument in the industry. It adopts the OTDR technical principles and integrates the powerful analysis software, which enables the TW3304N fiber ranger detect fiber faults location more accurate and easy.
