HV Test
-
Product
Cable Assembly, 37-Pin D-Type, Male To Unterminated With Ferrules, 0.5m, HV
40-972-037-0.5m-MUHV
-
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock.
-
Product
High Temperature Component Test Fixture
16194A
-
Measure both axial/radial leaded devices and SMD within the temperature range from -55 to +200°C.
-
Product
Universal Function Test System for Industrial Electronics
-
General functional test system based on LXI instrumentation for high mix / low to medium volume manufacturing. DUTs are tested which are mainly used as communication and measurement modules in power plant technology, grid management and electrical drives.The system has a Virginia Panel adapter interface to which various desk adapters can be docked, including automated contacting of the DUTs. A camera for the verification of light emitting diodes on the test object is integrated in the adapter interface.
-
Product
Application Software for Electronic Test & Instrumentation
-
Application software provides configuration-based workflows for electronic test and instrumentation applications. Application software is part of the NI software portfolio.
-
Product
Dual Channel HV Amplifier with Phase Inverter
A400DI
-
This unit contains two independent A400 amplifiers that share common ground reference and power supply. Please see A400 page for technical details.It features also a low voltage phase inverter that inverts the signal applied to the input of channel 1. The resulting signal can then be connected to the input of channel 2 by means of a short BNC cable (supplied). As a result the two outputs operate in counter-phase. Connecting a load between the outputs effectively doubles the amplitude range. Please note that the load cannot have any connection to ground.
-
Product
50-Pin D-Type Female without Backshell, HV
92-960-050-F-HV
-
This connector is designed to allow users to directly terminate cables with soldered connections. 50-Pin Female HV connectors can be directly mated to a corresponding Pickering Switching Module.
-
Product
Die Test Handler
3112
-
Chroma 3112 is a productive pick & place handler for high volume single- or multi-site bare die testing.
-
Product
BMS Manufacturing Test System
-
The Battery Management System (BMS) Manufacturing Test System performs functional testing of product during end-of-line manufacturing. The system hardware includes all instrumentation to test a BMS, including multiple cell simulators, a mass interconnect for quick product transition and bed-of-nail fixtures to ensure less down time, higher throughput, and easy maintenance. The system application easily integrates into manufacturing processes, provides a method to test multiple product types, and optimizes tests to ensure only good product is released from manufacturing.
-
Product
Cable Assy 37-Pin D-Type M/F 0.5M HV
40-970-037-0.5m-MF-HV
-
37-Pin Male to Female D-Type Cable Assy - High Voltage, 0.5m Long.
-
Product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Ferrules, 1m, HV
40-972-037-1m-FU-HV
-
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Tinned Ends, 2m, HV
A037DF4-T-HA200
-
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assembly. 9-Pin D-Type Male To Unterminated With Ferrules, 1m, HV
40-972-009-1m-MU-HV
-
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot breakwhen they are terminated.
-
Product
Cable Assembly, 9-Pin D-Type Male To Unterminated With Ferrules, 0.5m, HV
40-972-009-0.5m-MU-HV
-
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
Product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Tinned Ends, 2m, HV
A037DM5-T-HA200
-
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assembly, 9-Pin D-Type, Male to Unterminated With Cut Ends, 2m, HV
A009DM5-C-HA200
-
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
Product
Cable Assy 37-Pin D-Type F/F 2m HV
40-970-037-2m-FF-HV
-
37-Pin Female to Female D-Type Cable Assy - High Voltage, 2m Long.
-
Product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Cut Ends, 0.5m, HV
A037DF4-C-HA050
-
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assembly, 9-Pin D-Type Female to Unterminated With Tinned Ends, 1m, HV
A009DF4-T-HA100
-
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
Product
Wafer Test
-
Based on the reliability test, CSE conducts the test of the IC chip through electrical signals to the semiconductor wafer. We provide various Test Solutions according to the needs of designers/manufacturers. by sorting out good and bad products.
-
Product
Testing and Measurement
-
AkroMetrix provides a variety of products to help you identify and evaluate warpage: For warpage measurements along a production line or at room temperature, AkroMetrix has developed the LineMoiré Production Level Automated Flatness Inspection System. If you need to measure warpage and flatness during pre-defined temperature profiles, AkroMetrix's TherMoiré In-Process Warpage Measurement Systems may fit your requirements.
-
Product
Magnet Testing
MHLS
-
The MHLS is extremely flexible to use thanks to its compact and robust design. The development of ever more efficient electric motors in areas such as automotive engineering and wind energy is playing an ever increasing role, where the highest precision and quality of the magnetic components used is crucial, particularly in the energy and mobility transition.
-
Product
Test Programming
-
Terotest offers a full test programming service for all of our Automatic Test Equipment. In many cases test programs can be generated from CAD data on the product or component under test, or from autolearn facilities within the test system. Such techniques maximise accuracy and test program fault coverage, and allow quick and easy test program generation.
-
Product
Test Chambers
-
Drug test chamber, ozone test chamber, plant grown chamber, salt spray test chamber, sand test chamber, temperature and humidity test chamber, UV test chamber, xenon test chamber
-
Product
Package Testing
-
Delserro Engineering Solutions
Package testing is performed to test the durability of packaged products in their shipping containers. Both the shipping container and the effectiveness of the packing are being tested. Typical specifications include ISTA, ASTM D999, ASTM D4169 and ASTM D4728.
-
Product
Material Testing
-
In order to meet the constantly increasing quality requirements for products and their materials, we at Zentro test our products in our in-house EMC laboratory.
-
Product
2-Quadrant Source/Measure Unit for Functional Test, 20 V, 1 A or 6 V, 3 A, 20 W
N6782A
-
The Keysight N6782A is a source/measure unit (SMU) designed specifically for advanced functional testing of a device. The ability to modulate the output up to 100 kHz along with capability to source and sink current (2-quadrant operation) makes the N6782A a perfect fit for advanced functional test of a variety of devices such as DC/DC converters, power management units, power amplifiers, and power management ICs. The input stage of the DUT can be stimulated by the fast sourcing and waveform capabilities. While the output stage can be loaded down and measured with the electronic load capabilities, providing a total test solution.
-
Product
PRODUCTS TESTING
ESD
-
MicroStat Laboratories -R.E.T.S.
Our ESD test capabilities include resistance, resistivity, electrostatic shielding, charge generation, and charge dissipation. We routinely test flooring materials, packaging, footwear, garments, ionizers and many other ESD control products and materials. We utilize the relevant test methods and standards of the ESD Association, ANSI, ASTM, NFPA, IEST, IEC, AATCC, or our clients’ in-house specifications.
-
Product
Product Testing
-
Cotton Electric Services, Inc.
Cotton Services is accredited through the National Association of Independent Laboratories (NAIL). Our Testing equiptment goes through a calibration process at least once a year and on-site tests are routinely performed by factory officials to ensure testing accuracy. Cotton Services Employees are certified in equipment maintenance and testing procedures. All products are tested at or above minimum test ranges set by the industry.
-
Product
PRODUCTION TESTING
-
The Production Test Department is a component of the Engineering Department where production test technicians perform routine factory testing in accordance with approved test procedures. Most of the electronic testing is automated, whether ambient acceptance testing or environmental ESS testing.
-
Product
Test Automation
-
PrimeTest Automation delivers custom test, measurement, and data acquisition systems that include the best hardware and software available. Drawing on vast resources from multiple disciplines, each system is carefully designed and constructed to provide the most accurate and repeatable results. Test systems can be deployed as standalone or as part of an automated line such as a rotary index dial or conveyor.
