-
product
Switching System Test Tools
EBIRST™
Switching systems are an important part of many test systems, however, the switching system is in a vulnerable place. When accidents happen that can cause a faulty device, you need a way to get the system up and running again with a minimum of effort and operator skills.
-
product
6 Sided Bed of Nails Testers
BoxProber Family
6 sided Bed of Nails circuit board test fixture. Probes top bottom and all 4 sides. Central camming mechanism pull plates inward. Mechanically or electrically actuated options. Designed primarily for testing products in plastics. Side access electrically probes outside panel connectors. The unit will also optically read LEDs and key segments off LCD displays. Solenoids will press buttons and servos will turn selector switches. DC motors are used to adjust multiple turn potentiometers. Microphone...show more -
product
2 GHz Dual 1:4 RF Mux, 75 Ohm Module for 34970A/34972A
34906A
The Keysight 34906A RF multiplexer module for the 34970A/34972A Data Acquisition/Switch Unit offers broadband switching capabilities for high-frequency and pulsed signals. Use it to route test signals between your device under test and your signal generator, oscilloscope, spectrum analyzer, or other instrumentation. The RF multiplexers are arranged as two independent 1 x 4 multiplexers, each with a common shield and a switched center conductor. Connections can be made directly to SMB inputs with...show more -
product
Cable Tester
KT-200
Test with UTP (Unshielded Twisted Pair) and STP(Shielded Twisted Pair) cable. Check continuity and configuration of wiring with unshield and shielded modular plugs. Test for open circuits, shorts, miswires, reversals, and split pairs. SHIELD detection tests a cable's shield integrity. Test T568A,T568B ,!0 Base-T and Token Ring configurations. Special switch for select symmetric configurations or Non-symmetric cable use for connecting 2 PC.
-
product
EBIRST 104-pin D-type To 96-pin SCSI Adapter Cable
93-022-226
The 93-002-226 104-pin to 96-pin eBIRST adapter cable is part of a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
AC Power Sources
RS Series
AMETEK Programmable Power, Inc.
The RS Series consists of multiple high power AC and DC power systems that provide controlled AC and DC output for ATE and product test applications. This high power AC and DC test system covers a wide spectrum of AC and DC power applications at an affordable cost. Using state-of-the-art PWM switching techniques, the RS series combines compactness, robustness and functionality in a compact floor-standing chassis, no larger than a typical office copying machine. This higher power density has been...show more -
product
FD-11637, 8-Channel Strain/Bridge Input Device for FieldDAQ
785641-01
8-Channel Strain/Bridge Input Device for FieldDAQ - The FD-11637 can measure eight channels and has built-in bridge completion and voltage excitation to support for quarter-, half-, and full-bridge sensors. It also features anti-alias filtering, offset nulling, and shunt calibration to reduce the effect of noise and improve measurement accuracy. The FD-11637 has an ingress protection rating up to IP67 (dust- and water-resistant), can operate in -40 °C to 85 °C environments, and can sustain 100 g...show more -
product
Deluxe Automotive Meter with RPM & Temperature
585
The #585 is a professional grade tool used for diagnosing electrical, computer and engine problems on any vehicle. The #585 includes two sets of test leads, RPM pick-up, temperature probe, protective holster, 9 volt battery, instructions manual and carrying case. Inductive RPM pick-up features a five position, adjustable sensitivity switch.
-
product
PXI SPDT Switch: 26-ch, 2A, Armature Relay
M9130A
The M9130A is a general purpose switch with 26 independent, single-pole, double-throw (Form C) switches in a single PXI module. This module can be used to cycle power to products under test, control indicator and status lights or actuate external power relays and solenoids. The armature relays can handle up to 60W power. When needed, these relays can handle up to 6A pulsed carry current. Choose from the durable connector block or standard cable connections.
-
product
Low PIM Coaxial Switch, DC to 20 GHz, SP4T
87104Q
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87104Q is a low PIM SP4T coaxial switch, operating from DC to 20 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency and ultimately maximizes test throughput.
-
product
Digital Wideband Transceiver Analysis
S94610B
Digital Wideband Transceiver Analysis is an add-on software to Device Measurement eXpert (DMX) that adds cross-domain stimulus response measurements for digital/RF mixed-signal device characterization. Included Waveform Creator helps define digital IQ test stimulus waveforms that are used in the RF signal generators for receiver tests or downloaded to the digital-to-analog converters for transmitter tests. The DUT control is customizable to accommodate various data converters and transceiver typ...show more -
product
PXI-2585, 10‐Channel, 12 A, 1-Wire PXI Multiplexer Switch Module
778572-85
10‐Channel, 12 A, 1-Wire PXI Multiplexer Switch Module —The PXI‑2585 is a high‐power PXI multiplexer switch module that is ideal for switching power signals and loads in control applications and battery, power supply, and automotive testing. It is configured as a 10x1 multiplexer with both low contact resistance and high isolation voltage. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
product
300W Electronic Load
EL3630B
Features:*Number operation and control*LED display with high definition and high contrast, rich display information*Easy operation of knob encoder switch*Basic load function: constant current, voltage, power and resistance*Multi units used to multiple load ability*Short-circuit test*Battery test*Dynamic test*Multi parameters measured in the list*Remote voltage measurement*Panel and exterior trigger function*Protection function: over-voltage, over-current, over-power, over-heat, polarity connection in reverse*10 sets of parameters memorized and loaded, and automatically loaded on turning on the instrument*Intelligent fan control*Key lock and knob lock functions
-
product
SWB-2810, 4x43, 1 A, Row Access, Reed Relay Matrix Module for SwitchBlock
781420-10
4x43, 1 A, Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2810 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
Automated Optical Switch - PXI
Add optical switching capability to your test system with Quantifi Photonics’ automated optical switches. The fast and reliable optical switch will enable automated sequential testing, saving time and streamlining your test procedures.
-
product
Cable Test Van
BAUR Transcable 4000/S 70-3
BAUR Prüf- und Messtechnik GmbH
Transcable 4000/S 70-3. The transcable 4000 70 kV 3/S cable test van varies in comparison with the transcable 32 kV - 3S in the 70 kV voltage level. The system is controlled with the MGS semi-automatic control unit. The high voltage switch unit is 3-phase, air and solid matter insulated and safe to touch.
-
product
Insulation & Multifunction Tester (OLED Display)
1152 MF-M
Standard Electric Works Co., Ltd
● High Contrast OLED display.● Designed for viewing in the dark, for mining industry.● Auto-range microprocessor-controlled.● Automatic voltmeter AC/DC at Start/Reset.● Battery test at switch ON/Reset.● Safety voltmeter before each test.● Auto-discharge on all tests and all ranges.● Leads auto-null key.● Test auto-stop.● Smart hold and stop on voltmeter AC/DC.● Ener-Save.● Continuity short circuit >220mA.● Continuity open circuit voltage of 5Vdc.● Nominal voltage @ 1mA on all insulation ranges.● Polarization index (PI).● Dielectric Absorption Ratio (DAR).● BS 16 edition.
-
product
SWB-2817, 16x22, 0.3 A, Reed Matrix Module for SwitchBlock
781421-17
16x22, 0.3 A, Reed Matrix Module for SwitchBlock - The SWB‑2817 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
Transformer Variable Radio Tester
WABC
Wuhan Sangao Electrical Test Installations Limit Co.
Acc to IEC and Relevant national standard, In the power transformer production, transfer and user test process, Transformer ratio test is necessary project, This can be used for quality supervision of transformer factory and the use process, prevent the transformer winding inter turn short circuit, open circuit, connection error, pressure regulating switch failure or contact fault.So our company development and production of automatic ratio tester in the original basis according to the user's s...show more -
product
Twin columns automated force test stand 48" travel - 20,000 lb
720TN
The advanced 720TN Series Universal Test Systems are ball screw driven test stands, excellent for affordable, precision tensile and compression testing of a wide variety of materials, products or ASTM standards. These variable speed testers have increased speed ranges and include adjustable travel limit switches. With the unique dual testing area, users can setup for two tests, tensile and/or compression, without having to switch out fixtures.
-
product
AC Power Sources
BPS Series
AMETEK Programmable Power, Inc.
The BPS Series consists of multiple high power AC power systems that provide controlled AC output for ATE and product test applications. This high power AC test system covers a wide spectrum of AC power applications at an affordable cost. Using state-of-the-art PWM switching techniques, the BPS Series combines compactness, robustness and functionality in a compact floor-standing chassis, no larger than a typical office copying machine. This higher power density has been accomplished without the ...show more -
product
Automatic Production Tester for Electric Motor Stators
MTC 3
The fully automatic MTC3 stator testers test your windings reliably and quickly for possible insulation faults via our patented surge voltage test.After connecting the test object completely the test is performed with an automatic switching of the connections and the test methods. The MTC3 evaluates each test step. At the end of the complete test process it provides a clear and reproducible GO or NO GO-statement.
-
product
Powered VXS Crates
6U VXS 6021
The WIENER VXS 6023 crate series adds high performance Switch Fabrics according to VITA 41 specification to VME based systems. Designed primarily for high speed applications in data acquisition, as well as military / aerospace test and instrumentation it combines superior mechanical quality with lowest noise power supply technology.
-
product
Rail Traction Inverter Test System
The rail inverter test system uses a pulse test methodology to verify proper operation of the IGBT switching elements in a subway car motor control. The system is designed to verify proper commutation of the switching elements. A large capacitor bank allows testing at DC voltages up to 1kV and peak currents of up to 3kA into reactive loads.The system also integrates self test capabilities and safe-to-turn-on (STTO) diagnostics to ensure no gross faults are present prior to the application of high voltages. Further the system includes dielectric withstand (hi-pot) test capability to ensure electrical safety.
-
product
Electrical Contacts Test
The electrical contact testing is performed to determine the reliability of equipment under various contacting conditions. A few types of electrical contact tests are: contact-chatter monitoring, contact resistance, intermediate, and low level contact switching.
-
product
PXI 3A Power MUX BRIC, 6-Channel, 48-Pole
40-571-006
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
Circular Locus Tester
TF225
TESTEX Testing Equipment Systems Ltd.
Circular Locus Tester, to determine surface deterioration and quality of fabrics (wool, chemical fiber, mixed, kitted and woven fabrics). Using an active friction system, fabric is rubbed against a nylon brush and abrasive or an abrasive only under controlled conditions. Results of the test are achieved in minutes. The relative motion of the locus specimen grip and the abrasive platform is a circle with a relative speed of 60+/-1 r/min. The grip offers pressure to the specimen which is adjustable with a tolerance of +/-1%. For added control and safety, the machine is equipped with a self-stop switch.
-
product
Dedicated Testers
Dedicated Testers are often inexpensive due to their low test point requirements, which allow for a reduction in switch cards, especially when compared with a Universal Tester. Ease of setup is accomplished through the utilization of transfer connectors between the fixture and the machine. However, this can contribute to a higher fixture cost than typically seen with a Universal Test Fixture due to the nature of their construction which is labor intensive.
-
product
Active Switching Rectifiers, 2 KW, P/N 6016C
- Active Switching Rectifier, 2 KW, P/N 6016C- Input Range: 9 VAC to 35 VAC, 3 PH- Frequency Range: DC to 10 kHz- DC output: 13.5 VDC, 70 Amps without any heatsink (Test #1)- DC output: 13.5 VDC, 150 Amps with heatsink (Test #2)- Dimensions: 8″W x 8″L x 3″H or similar- AC to DC and DC to DC applications- Generates less heat as power MOSFET Switching is used- The output voltage is the same as the input voltage
-
product
Power device test system
This system is suitable for DC testing of IGBT, IGBT module (1in1～7in1). Built-in hi-current switching relay circuit inside test head, it is capable ofDC testing from device itself to module. Highly accurate repeatability testing is available by high speed rise time which is suppressed its heat in hi-current
