Pickering Interfaces Inc.
Pickering Interfaces designs and manufactures modular signal switching and simulation for use in electronic test and verification.
- 781 897 1710
- ussales@pickeringtest.com
- 170 Main Street
Unit 108
Tewksbury, Massachusetts 01876
United States
-
product
LXI Microwave Multiplexer, SP4T, 11-Bank, 18GHz, 50Ω, SMA
60-803-111
Our 60-803-111 is a 11 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 18GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
Cable Assembly, 50-Pin D-Type, Female To Female, 2m HV, Exit Away From Pin 1
40-970-050-2m-FF-HV
50-Pin Female to Female D-Type Cable Assembly, High Voltage, 2m Long, 45º Cable Exit Away From Pin 1.
-
product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 4.09k Ohm
50-294-023
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI Dual Microwave SPDT Relay 12.4GHz 50 N-Type
40-780A-512
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
-
product
PXI 5A Mux 4-Bank 11-Ch Isolated COM
40-651-013
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel.Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
product
PXI 8-slot BRIC Matrix, 320x16, 1 pole (10 Sub-cards)
40-558-801-320x16
The 40-558-801-320x16 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
15 Pin D-Type Connectors
The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
product
PXI 8 Slot BRIC 460x8 1-Pole Dual Analog Bus (10 sub-cards)
40-560A-121-460X8-M
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI/PXIe Microwave Relay, Dual SPDT, 26.5 GHz, 50 Ω, SMA, External Termination, Failsafe, Remote Mount
40-781A-322-E
The 40-781A-322-E (PXI) and 42-781A-322-E (PXIe) are dual failsafe SPDT 26.5 GHz microwave relay modules with external terminations and remotely mounted relays. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
product
100-Pin Micro-D Connector, Male, Discrete Wire, 2-56 UNC Screwlocks, Metal Shell
C100SMR-1CW-6A
This accessory is designed to allow users to directly terminate a cable to the connector. It is difficult to terminate cable to the 100-Pin SCSI Style Micro-D connector because of the high density and fine pitch. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
product
PXI/PXIe RF Multiplexer, Dual 4-Channel, Terminated, 8GHz, 50Ω, SMA
40-882B-002
The 40-882B-002 (PXI) and 42-882B-002 (PXIe) are dual 50Ω 4 to 1 RF multiplexers with 8GHz bandwidth.The 40/42-882B range has automatic termination of unused signals and are available as a single MUX in one slot, a dual MUX in two slots, or triple and quad MUXs in three slots.
-
product
68-Pin VHDCI Connector Blocks
The connector blocks below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to Female (Female Screwlocks), 1m
A200LMR-200LFR-5B100
This male to female 1m cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin connector and is constructed from 4 bundles of 50-wire round/flat ribbon cable. The connector assembly can be secured to the product by screwlocks.
-
product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Tinned Ends, 2m, Screwlocks
A068SMR-T-6B200
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
product
High-Density PXI Multiplexer Switch Modules
This range of High-Density Multiplexer Switch Modules provides a compact array of MUX solutions with differing combinations of channel counts and poles. Most of our high-density solutions include isolation relays that allow the MUX to be disconnected from the single input/output port, enabling the convenient interconnection of other channels.