Pickering Interfaces Inc.
Pickering Interfaces designs and manufactures modular signal switching and simulation for use in electronic test and verification.
- 781 897 1710
- ussales@pickeringtest.com
- 170 Main Street
Unit 108
Tewksbury, Massachusetts 01876
United States of America
- PXI Chassis and Remote Controller
- Configurable PXI & PXIe Microwave Switch Platform
- PXI Power Supply Modules
- High-Voltage LXI Matrix Modules
- PXI Precision Programmable Resistor Modules
- PCI Precision Programmable Resistor Cards
- LXI 50 RF Matrix - 2.4GHz
- 25 Pin D-Type Cables - Connector to Unterminated for Pickering
- 25 Pin D-Type Cables - Connector to Unterminated
- Resistance Temperature Detectors (RTD) Simulators
- 2 Amp PXI Large Matrix Modules
- PXI Chassis
- 20-Pin GMCT Connector & Cable Accessories
- 25 Pin D-Type Cables - Connector to Connector for Pickering
- 25 Pin D-Type Connectors for Pickering
- PCI Switch & Simulation Cards
- LXI Switching Solutions
- LXI RF & Microwave Switching Solutions
- PXI Prototyping and Breadboard Modules
- PXI Attenuator Modules
- PCI Standard Programmable Resistor Cards
- PXI Simulation Modules For Sensor Simulation
- 25 Pin D-Type Connector Blocks for Pickering
- 68 Pin 1.27mm Pitch Micro-D Connectors for Pickering
- PXI Switch Solutions
- PXI Chassis And Remote Controllers
- Cables And Connector Solutions
- PXI High Voltage Amplifiers
- 20 Pin GMCT Cables - Connector to Unterminated for Pickering
- PXI Digital I/O Modules
- PXI Instrumentation Modules For Automated Test Systems
-
product
PXI 12-Slot BRIC Matrix, 924x6 1-Pole (11 Sub-cards)
40-558-121-924X6
The 40-558-121-924x6 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
3 Pin Power D-Type Cables - Connector to Connector
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
product
Cable Assembly, 50-Pin D-Type, Female To Unterminated With Ferrules, 1m HV, Exit Away From Pin 1
40-972-050-1m-FU-HV
50-Pin Female to Unterminated D-Type Cable Assembly, High Voltage, With Ferrules, 1m Long, 45º Cable Exit Away From Pin 1.
-
product
LXI High Density 128x16 2A Matrix
60-554-004
A high-density single pole matrix module capable of switching up to 300VDC/250VAC, 2A (60W max). The use of high-quality electro-mechanical relays offers high switching confidence for signal routing in large ATE systems.
-
product
50-Pin D-Type Female Connector Block
92-965-050-F
This connector block provides a simple method of connecting to 50-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties.
-
product
PXI/PXIe 15W Programmable Resistor Module
40-254-032
The 40-254-032 (PXI) and 42-254-032 (PXIe) are programmable resistor modules with 1 channel which can be set between 2Ω and 26.7kΩ with 0.5Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
product
PXI 2A Multiplexer, 4-Bank, 32-Channel 1-Pole
40-614-006
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
product
PXI 2A Multiplexer, 2-Bank, 4-Channel, 16-Pole
40-614C-014
This 2-bank, 4-channel, 16 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
PXI 50 x DPST Electromechanical Relays
40-146-202
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
product
PXI 8x8 Matrix Module, 2-Pole 2A,60W
40-516-002
The 40-515/516/517 2 Amp, 2-Pole Matrix Modules form part of the System 40 PXI ProgrammableSwitching system. Each module consists of a matrix of 64 2-pole electro-mechanicalrelays under the control of a PXI/PCI interface.These modules are designed for switching medium voltage/power signals in test applicationswhere reed relays do not have sufficient rating. They are also suitable for telecomsapplications where send and return signals need to be switched simultaneously.
-
product
PXI/PXIe RF Multiplexer, Single 4-Channel, 3GHz, 50Ω, SMB
42-872A-001
The 40-872A-001 (PXI) and 42-872A-001 (PXIe) are 50 Ohm 4 to 1 RF multiplexers with 1 bank in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
product
PXI Dual SP4T MUX 6GHz 50Ω SMA
40-784-102
Pickering Interfaces’ 40-784 PXI Microwave Multiplexer Modules have a characteristic impedance of 50 Ohm and are capable of switching signals up to 40GHz. Available in single or dual SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
PXI Quad 4 to 1 Mux 1.3GHz 50Ohm SMB
40-749-511
The 40-749 is a quad 4 to 1 RF MUX available in 50 Ohm or 75 Ohm versions occupying a single PXI slot. The module is available with SMB or SMA connectors for 50 Ohm versions or, 1.0/2.3 or Mini SMB connectors for 75 Ohm versions. Applications for the 40-749 include routing high frequency signals to and from oscilloscopes, analyzers, signal generators and synthesizers, telecoms tributary switching, video/audio switching and switching high frequency logic signals.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode, 9/125 Fiber, MU Connectors, With Interlock
42-850A-314-HI
The 40/42-850A-314-HI is a PXI/PXIe 4-channel multiplexer with MU (mini SC) connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
PXI 3A Power MUX BRIC, 6-Channel, 16-Pole
40-571-202
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
Related
-
Virginia Panel Corporation
Virginia Panel Corporation (VPC) provides VPC provides Interconnect Solutions that enable simultaneous connection of multiple test and measurement signal types through one modular interface. Designed to accommodate signal, power, RF, thermocouple, pneumatic/vacuum, and fiber optic connector modules in multiple configurations, VPC’s innovative products meet the demands of test & measurement interconnect requirements.
