Showing recent results 1681 - 1695 of 2348 products found.
-
40-761-004 - Pickering Interfaces Ltd.
This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk. These RF multiplexers exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 600MHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths has been minimized by careful attention to the mechanical and electrical design. User connections are made via SMB connectors; you can find the associated RF cable & connector accessories data sheet under the downloads tab above.
-
40-761A-004 - Pickering Interfaces Ltd.
The 40-761A-004 terminated quad 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
40-762-004 - Pickering Interfaces Ltd.
This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk. These RF multiplexers exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 600MHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths has been minimized by careful attention to the mechanical and electrical design. User connections are made via SMB connectors; you can find the associated RF cable & connector accessories data sheet under the downloads tab above.
-
40-763-004 - Pickering Interfaces Ltd.
This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk. These RF multiplexers exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 600MHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths has been minimized by careful attention to the mechanical and electrical design. User connections are made via SMB connectors; you can find the associated RF cable & connector accessories data sheet under the downloads tab above.
-
40-763A-004 - Pickering Interfaces Ltd.
The 40-763A-004 terminated quad 8 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Pickering Interfaces Ltd.
Pickering's RF PXI Matrix Modules are capable of providing economic switching for frequencies up to 6 GHz. Our other RF PXI options include RF SPDT switches and RF multiplexers, for higher frequency applications or applications requiring high-performance levels, please take a look at our microwave switching modules.
-
Pickering Interfaces Ltd.
Pickering's RF SPDT PXI Switch Modules are capable of providing economic switching for frequencies up to 6 GHz. Our other PXI RF options include RF matrices and RF multiplexers. For higher frequency applications or applications requiring high performance levels, please take a look at our microwave switching modules.
-
50-262-102 - Pickering Interfaces Ltd.
This RTD Simulator is a PCI card that supports 6 channels of RTD simulation. The card can provides a setting resolution of <90mΩ (also available in <8mΩ - PT100) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
90-200-001 - Pickering Interfaces Ltd.
Each power outlet can be programmed to switched on in sequence with a specific timing delay. The delay can be staggered to ensurethat order dependent systems - like PXI - can be switched on and off in an orderly way with just one operation. A staggered start upalso limits the inrush current associated with the powering up of equipment, including earth current inrush, placing less stress oncabling and leakage breakers. Power on or off instructions can be initiated from either the front panel switch or via the serial interface.
-
Pickering Interfaces Ltd.
In test system development, the best hardware is only usable if its software control environment is robust and easy to use. If you are a test system developer, you need to look at both the hardware and software aspects of your vendors of choice.
-
41-921-001 - Pickering Interfaces Ltd.
Supports two PXI chassis from a single PCI card2.5Gb/s StarFabric serial interface ensures fast operationSupports 32/64 Bit & 33/66 MHz PCI interfacingUses RJ45 connectors, shielded Cat 5E cablesOperating system independentLow power consumption, supporting 5V and 3.3V PCISingle slot 3U PXI
-
41-921A-001 - Pickering Interfaces Ltd.
Supports two PXI chassis from a single PCI card2.5Gb/s StarFabric serial interface ensures fast operationSupports 32/64 Bit & 33/66 MHz PCI interfacingCompatible with Windows 7 32/64-BitUses RJ45 connectors, shielded Cat 5E cablesOperating system independentLow power consumption, supporting 5V and 3.3V PCISingle slot 3U PXI
-
Pickering Interfaces Ltd.
Pickering Electronics Surface Mount Reed Relays contain the highest quality instrumentation grade reed switches making them suitable for the most demanding applications and are suitable for infra-red or vapor phase reflow soldering.
-
eBIRST - Pickering Interfaces Ltd.
The eBIRST toolset consists of three different tools that support 200-pin LFH, 78-pin and 50-pin connectors and a set of adaptors that allow connection to other connector types. A supplied application program controls the eBIRST tools via a USB2 port that also provides the tool power and controls the switching system using a Test Definition File to define the test sequence. These tools work by measuring the path resistance at the switching system external connectors using four-wire measurements, quickly establishing whether the path is good, has increased resistance or has failed. Below are links to various eBIRST tool information:
-
Pickering Interfaces Ltd.
The data signal paths on these USB data communications multiplexers are 2-pole arranged as differential pairs as defined by the USB standard. The signal pair has a controlled differential impedance and the multiplexer has been designed for minimum insertion loss. The USB power paths are arranged as a common negative and a switched positive. The power paths are designed to ensure minimum loss of the USB power.
