James Instruments Inc.
James Instruments Inc. is the leading manufacturer of non-destructive test equipment for concrete and other coarse grained materials. We supply the instruments that measure and analyze strength, structure, corrosion and moisture in concrete.
- 1-800-426-6500
773-463-6565 - 773-463-0009
- info@ndtjames.com
- 3727 N. Kedzie Avenue
Chicago, IL 60618
United States
-
product
Resonant Frequency Testing
E-Meter MK II™
Determines resonant frequencies of the three modes of vibration. Material characteristics such as Youngs Modulus of Elasticity, Modulus of Rigidity, Poissons Ratio and Damping Constant can be calculated. Frequencies are automatically scanned in one of four ranges. The system can determine flexural resonance of concrete under accelerated freezing and thawing cycles and aggressive environments.
-
product
Impact Echo SystemFor Field Evaluation of Concrete Structures
Vu-Con System
The Vu-Con Analyzer provides the engineer with the sturdiest, most reliable system for impact echo analysis. No moving parts and implementation of the latest microcomputer technology has created a system that is both sophisticated and reliable. The unit comes with a 90 mm (3.5?) by 115 mm (4.5?) graphic display screen that is easily viewed in daylight
-
product
Chloride Test System
C-CL-2000
The C-CL-2000 produces results on-site, within minutes that are accurate and comparable to expensive laboratory tests. It measures the electrochemical reaction of a weighted sample placed in an extraction liquid. It automatically shows a temperature compensated reading of percent of chlorides on its digital display. A wide range - from 0.002 to 2% chloride by weight - is covered.
-
product
Hand Held Microwave Moisture MeterFor Water/Cement Ratios of Fresh Concrete
Cementometer
The James Cementometer represents a break-through in modern moisture measurement technology. By utilizing the latest microwave and microprocessor science, the Cementometer can determine the moisture content of freshly mixed cement, concrete, and mortar. Simply insert the prongs of the probe into the material to be measured and instantaneously the water cement ratio is shown on the easy to read display.
-
product
Rebar Corrosion Rate Determination System
Gecor 6
Measures the rate of corrosion and other parameters of rebars. The Gecor 6 utilizes the polarization resistance technique to establish the corrosion rate. This is a quantitative measure of the amount of steel oxidizing at the time of measurement. Up to 100 readings can be stored in memory for later uploading to a Personal Computer.
-
product
Resistivity Meter for Concrete
Ohmcorr Test System™
OhmCorr has two probes spaced 1.97" (5cm) apart which are placed in holes drilled to a depth of 3/8th" (8mm) and filled with conductive gel. The direct digital read-out of resistivity is displayed on the LCD when the control switch is activated. OhmCorr and CorMap, when used together, provide an economical and sound diagnostic system of corrosion in reinforced concrete.
-
product
Moisture Master
T-M-170
The James Instruments Moisture Master utilizes the latest electronic technology to measure the quantity of water within its sensing field. The unit has two modes of operation the pin mode, and search mode. In the pin mode, two pins are pushed into the material and a high frequency field is created between these two pins.
-
product
Aquameter
T-M-160
he James Instruments? Aquameter MK II utilizes the latest electronic technology to measure the quantity of water within its sensing field. The T-M-160 using a high frequency capacitive sensor, samples a large volume of material, approximately 460 mm x 670 mm x 25 mm (1 13/16? x 2 5/8? x 1?), instantaneously.
-
product
Ultrapulse
The James Ultrapulse is ideally suited for the testing of ceramic materials, refractories, plastics and laminates. Ultrasonic velocity measurement permits accurate and repeatable calculation of modulus of electricity, bulk density and the detection of cracks. Stored data can be uploaded to a PC with the optional hand-held terminal. The Ultrapulse can be used with a wide range of ultrasonic stansducers for all of your ceramic testing needs.
-
product
Measures Wide Range of Anchor Strengths
Anchor Test System
Two models, each with two different gauge capabilities enable precision readings over a wide range of applications - from light to heavy duty loads. The standard system has a pull stroke of two inches with an option to extend to four inches. The longer pull stroke allows for complete extraction of most fixings in one simple operation. A load diffusion bridge and pyramid are available to keep reaction loads away from the anchor point.
-
product
Concrete Hardness Tester
W-M-250
The W-M-250 Manual Test Hammer is the traditional instrument used for the non-destructive testing of hardened concrete. This easy-to-use instrument provides a quick and simple test for obtaining an immediate indication of concrete strength in various parts of a structure. The minimum verifiable strength is 1400 PSI (10 MPa)
-
product
Ultra-sonic Test System
V-Meter
The V-Meter is an advanced ultrasonic, pulse-velocity test system widely used for quality control and evaluation of concrete structures. It can identify non-homogeneous conditions such as voids, cracks, honeycombs and frozen concrete.
-
product
Strength Testing of Concrete, Brick and Mortar
Windsor Pin System
Measures the compressive strength of concrete, mortar and brick in-situ, quickly, accurately. A non-explosive instrument, the Windsor Pin System uses a spring-loaded device to drive a steel pin into the concrete or mortar.
-
product
Digital Test Hammers
James Instruments? digital test hammers are an advanced, completely automated system for estimating concrete compressive strength. Its calculation, memory and recording functions allow for quick, easy and accurate test results.