Optomistic Products
Optomistic Products' Universal LightProbes™ are small, highly versatile sensors and fiber-optic probes for reliable LED test of color (including white LEDs) and LED intensity, on printed-circuit boards using in-circuit test (ICT) fixtures and automatic test equipment (ATE) for production testing of circuit boards and their components.
- (207) 865-9181
- (207) 510-8039
- info@optomisticproducts.com
- PO Box 751
S. Freeport, ME 04078
United States of America
Categories
-
product
IR LightSource
Universal LightSources emit Infrared (IR) radiant energy and are designed for the testing of IR(infrared) sensors used in remotely-controlled products.The Universal LightSources use a standard 5-volt DC power supply connected via a connecting cable with mating coaxial power plug and terminated with clearly polarized push-on connectors to access fixture 5-volt D.C. supply wire-wrap pins wherever available. Alternatively, the Universal LightSource can be connected to a serial-digital pulse-code-modulated signal source.
-
product
Accessories
Universal LightProbes are easily installed with one-hole fixing. Optomistic Products provides several accessories to make the use and installation of Universal LightProbes fast and simple, including The Sensor Six-Pack, Sensor and Fiber-optic Probe clamps, and Universal LightProbe Connector Cables.
-
product
Small Aperture Fiber-Optic Probes
Small-aperture Fiber-optic Probes are best for testing closely-spaced LEDs. With an aperture of 1mm, and a diameter of 1.2mm/0.050 inches, they can test LEDs spaced as close as 0.050 inches on center. Small-aperture Fiber-optic Probes are available with straight or right-angle stainless-steel tips as shown below. This allows for precise customization to your mechanical constraints.
-
product
S2 Unicolor Digital Sensors
ULP-S2 SCC
The Universal LightProbe S2 Unicolor Digital Sensor is pre-programmed to respond only to a specific color LED, including blue, green, yellow, orange, red, plus white. The Universal LightProbe S2 Unicolor Digital Sensor is designed for the simple ON/OFF test and color check of a single color LED, with a digital output, quickly determining PASS/FAIL status without further processing by Automatic Test Equipment. The Universal LightProbe S2 Unicolor Digital sensor provides the simplest and fastest interface to Automatic Test Equipment (ATE).Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts, at 6mA max.; less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Loads: 20 mA max. Non-inductive.Output Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times: <10mS capture time; <65mS overall response timeFiber-Optic Probes: Can utilize any Universal LightProbe Fiber-Optic Probe
-
product
S2 Blinx Digital Sensors
ULP-S2 BLINX
The Universal LightProbe S2 Blinx Digital is designed for the simple ON/OFF test of any color blinking or steady-state LED, for fast results with a digital output. The Universal LightProbe S2 Blinx Digital Sensors check the ON/OFF status of any color LED, whether stable or blinking/pulsed, up to a rate of 15 Hz, and provide a Logic “1” output (5 volts) only if the LED is “ON” and a Logic “0” if the LED is “OFF.”Operating temperature range: 0oC to 70oCPower consumption: Operates from +5, 12, 24 or 28 volts D.C., at 6mA max.Voltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Load: 20mA max. (Source/Sink). Non-inductiveOutput Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times: <66mS, shorter for brighter LEDsFiber-Optic Probes: Wide Aperture Fiber-Optic Probe recomended
-
product
Trident Fiber-Optic Probes
Our most popular and cost-efficient option for the test of multiple LEDs — testing three LEDs with a single Sensor. This method of testing LEDs scales up, so that testing 3, 30, 300 — or any number of LEDs — is far more cost-efficient than other methods. This is our most popular Fiber-optic Probe and can be combined with any of our Universal LightProbe Sensors.
Related
-
DFT - MG-Products BV
DFT, Designed for Testing. is part of MG-Products and is specialized in the delivery of functional Testfixture solutions from both MG-products and 6TL. DFT also stands for Design For Test, perhaps the most important step in the development process of your product. DFT ensures that your product can be contacted and tested efficiently and reliably.
