Pulsar Microwave Corporation
Pulsar Microwave Corporation, established in 1987, is a U.S.-based manufacturer specializing in high-performance RF and microwave passive components spanning DC to 85 GHz. With full in-house design and manufacturing capabilities, we maintain strict control over quality, performance, and lead times, making us a trusted partner for both standard and custom-engineered solutions.
- 973-779-6262
- 973-779-2727
- sales@pulsarmicrowave.com
- 48 Industrial West
Clifton, NJ 07012
United States of America
-
Product
3-Way Power Dividers From 0.5 To 35 GHz
-
Pulsar Microwave's 3-way power dividers cover 500 MHz to 35 GHz in various connectorized packages. They are rated to handle 30 watts maximum input power for a load VSWR of 1.20:1 or better. The 3-way power combiners are available in both in-line and Tee configurations, and come standard with SMA or N female connectors.
-
Product
Image Reject Mixers To 16 GHz
-
Image Reject Mixers incorporate a 2-way 0° divider, two 90° hybrids and two mixers. They produce an IF signal when driven by an LO and RF signal while rejecting unwanted sidebands that are very close in frequency.
-
Product
Single Sideband IQ Modulators To 16 GHz
-
Single Sideband Modulators incorporate a 90° hybrid, 2-way 0° divider and two mixers to produce either an upper (RF + IF) or lower (RF - IF) sideband when driven by a carrier signal and modulation input signal. Depending on the phase relationship of the signals injected into the MOD.I and MOD.Q ports, the modulator will pass either the upper or lower sideband through to the output while rejecting the other.
-
Product
SP8T RF Pin Diode Switches To 12 GHz
-
Pulsar Microwave manufactures 8-way absorptive and reflective RF switches in single-pole 8-throw configuration. They fulfill broadband and narrowband requirements from 40 MHz to 12 GHz and handle 200 milliwatts input power. The SP8T switches have an isolation of 60 dB and switching time of 100 ns. Most models specify 1.6:1 or better VSWR at all ports. The SP8T switches operate on a power supply of +/- 5VDC and switching control is 0-5 TTL logic. The unit comes standard with SMA female connectors. Options for control are line drivers and decoders.
-
Product
90 Degree Hybrid Couplers To 500 MHz
-
Hybrid couplers with bandwidths as broad as 125:1 are available for applications within 100 kHz to 500 MHz. Power handling is 1 watt maximum for a load VSWR of 1.2:1 or better. These hybrids have an isolation of 20 dB and phase balance of 3 degrees. Most models have a VSWR of 1.4:1 or better throughout their operating bandwidths.Pulsar Microwave currently offers these hybrid couplers packaged in three outlines, including an SMT version. Standard offering of connectorized packages 412 and 442 are with SMA female connectors. Outline 412 may be customized with any combination of BNC, TNC, F or N connectors. Outline E is the surface mount version and requires less than one square inch of board area, making it well-suited for portable applications.
-
Product
12 / 16 / 32-Way Power Dividers From 0.5 To 8.5 GHz
-
Pulsar Microwave manufactures N-way power dividers in connectorized packages spanning 500 MHz through 8.5 GHz. These narrow and broadband models are designed to operate in a 50-ohm system and are rated at 30 watts.
-
Product
Quad IF Mixers / IQ Demodulators To 16 GHz
-
Quadrature IF Mixers incorporate a 90° hybrid, 2-way 0° divider and two mixers to produce two output signals in phase quadrature (I &Q) when driven by a LO and RF signal.
-
Product
SP1T RF Pin Diode Switches To 18 GHz
-
Pulsar Microwave manufactures pin diode RF switches that are controlled by TTL logic. This configuration is known as single pole, single throw and is often abbreviated SPST or SP1T. They have been engineered to function in 50-ohm systems, and are designed to operate from 40 MHz to 18 GHz. They have a switching time of 100 nanoseconds and input power rating of 200 mW (23 dBm). Performance of 1.6:1 or better VSWR and minimum isolation of 60 dB is typical of most models.All switches of this type require both +5VDC and -5VDC to operate. Typical current consumption is +/- 30 mA. TTL control logic of 0 to +5VDC is required. Units comes standard with SMA connectors.
-
Product
DC Blocks From 0.1 MHz To 18 GHz
-
Pulsar Microwave Corporation's DC blocks are designed to inner-only topology and utilize our standard housings for fast turn manufacturing. Designs are tested to 50 Ohms, and models range up to 18 Ghz with a maximum voltage rating of 500 Vdc.
-
Product
2-Way Power Dividers From 0.23 To 70 GHz
-
Pulsar Microwave manufactures a large selection of 2-way power dividers in narrowband and broadband configurations, covering frequencies from 225 MHz to 70 GHz. They are designed to handle from 10 to 30 watts input power in a 50-ohm transmission system. Microstrip or stripline designs are utilized, and optimized for best performance.Units come standard with SMA or N female connectors, or 2.92mm, 2.40mm, and 1.85mm connectors for high frequency components.
-
Product
Voltage Variable Attenuators To 16 GHz
-
Our family of voltage controlled attenuators is non-reflective, with ranges of 32 dB of 64 dB. Pin diodes are used and the frequency range is 0.25-16 GHz. They operate with a control voltage of 0 to +8 VDC and handle +27 dBm maximum input power. These attenuators are bi-directional: either SMA port may be used for an input.
-
Product
Double Balanced Mixers From 0.01 To 6000 MHz
-
A double balanced mixer (DBM) employs the use of a well matched quad-diode ring with two balanced transformers. Because of this, a DBM enjoys the inherent advantage of high port to port isolation. The IF port in Pulsar's DBM design is DC coupled to the diodes.
-
Product
SP5T RF Pin Diode Switches To 12 GHz
-
Pulsar Microwave's 5-way RF switches cover bands from 300 MHz to 12 GHz in both absorptive and reflective configuration. These SP5T switches have a rating of 200 mW maximum input power and a switching time of 100 ns. They are specified with a minimum isolation of 60 dB and most models maintain a VSWR of 1.6:1 or better on all ports. The SP5T switches are driven by TTL logic control circuitry and require both positive and negative 5-volt supplies for operation. A 9-pin D-SUB connector provides the interface for the power and logic voltages.
-
Product
Low Frequency 3-Way Power Dividers To 1500 MHz
-
Pulsar Microwave manufactures 3-way power dividers from 1 MHz to 1.5 GHz in both surface mount and connectorized packages. They are rated for an input power of 1 watt maximum for a load VSWR of 1.20:1 or better. This series of 3-way power dividers are currently offered in four outline packages. The hermetically sealed outline 301 and surface mount outline B are useful in portable applications where space is premium. Outlines 412 and 433 are connectorized versions in cross or in-line format, respectively.
-
Product
SP16T RF Pin Diode Switches To 10 GHz
-
Pulsar Microwave's 16-way switches cover 500 MHz to 10 GHz in single pole, 16-throw configuration. Maximum input power is 200 mW and switching time is 100 ns. SMA female connectors are standard. A 15-pin D-SUB male connector makes the internal connections to the power, ground and logic circuitry. Switching control is TTL with the option of line drivers and decoders.
