NI

Product

SWB-2813, 4x21, 1 A, 2-Wire Reed Matrix Module for SwitchBlock

781420-13

Matrix Switch Module

NI

781420-13 - NI

4x21, 1 A, 2-Wire Reed Matrix Module for SwitchBlock - The SWB‑2813 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.

Product

NI-9215, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module

783739-01

Voltage Input Module

NI

783739-01 - NI

±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9215 performs differential analog input. The module contains NIST-traceable calibration, a channel‑to‑earth ground double isolation barrier for safety and noise immunity, and high common-mode voltage range. It is also offered in two connectivity variants: 10‑position screw terminal or BNC.

Product

Oscilloscopes And Digitizers

Oscilloscope

NI

NI

Oscilloscopes and digitizers measure changes in electrical signals over time. Use these products for time‐ and frequency‐domain applications as well as to build spectrum analyzers, transient recorders, and many-channel phenomena detection systems.

Product

LabVIEW Development Systems

System

NI

NI

Base--The instant productivity of graphical development for DAQ and instrument controlFull--A rich set of routines for mathematics, signal processing, and signal generationProfessional--The solution for professional developers who need code deployment or validationLabVIEW suites--LabVIEW Professional plus industry-specific add-on software

Product

96-Pin Male SCSI to 96-Pin Female SCSI Switch Cable, 1m (protected)

150579-01

Switch Cable

NI

150579-01 - NI

96-Pin Male SCSI to 96-Pin Female SCSI Switch Cable, 1m (protected) - The SH96F-96M SwitchBlock SCSI Cable provides connectivity for SwitchBlock modules. You can connect these to the TBX-2809 Terminal Block, which exposes each channel of the switch module to screw terminals.

Product

sbRIO-9253, Non-Enclosed, 50 kS/s/ch, 24-Bit, 8-Channel C Series Current Input Module

787433-01

Current Input Module

NI

787433-01 - NI

Non-Enclosed, 50 kS/s/ch, 24-Bit, 8-Channel C Series Current Input Module - The sbRIO-9253 is an 8-channel analog input module for CompactRIO Single-Board Controller that provides a ±20 mA input range and 24 bits of resolution at a 50 kS/s sample rate. This module includes diagnostic functionalities to ensure nominal system operations with open-channel detection, power supply detection, and configurable thresholds. You can view the status of each channel and the power supply with eight LEDs. The sbRIO-9253 also features programmable hardware filters for your applications, such as specific Butterworth and comb filters that you can use to reduce the noise in your system.

Product

NI-9222 , ±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module

783283-01

Voltage Input Module

NI

783283-01 - NI

±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9222 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The NI‑9222 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the NI‑9222: a 10‑position screw terminal or a 25‑pin D‑SUB connector.

Product

PXI-4110, 3-Channel, 20 V, 1 A, 46 W, PXI Programmable Power Supply

779647-11

Programmable Power Supply

NI

779647-11 - NI

3-Channel, 20 V, 1 A PXI Programmable Power Supply—The PXI‑4110 is a programmable DC power supply. It is an excellent general-purpose, single-quadrant power supply for design validation and manufacturing test applications. The PXI‑4110 has two isolated and a single non-isolated supply channel, all capable of generating up to 1 A per channel. You can program the voltage setpoint and current limit as well as the voltage and current readback/measurement functionality. You can also combine channels for higher voltage or current.

Product

PXI-5650, 1.3 GHz RF Signal Generator

779670-00

RF Signal Generator

NI

779670-00 - NI

The PXI‑5650 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5650 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.

Product

cRIO-9068, 667 MHz Dual-Core CPU, 512 MB DRAM, 1 GB Storage, Zynq-7020 FPGA, Extended Temperature, 8-Slot CompactRIO Controller

782663-02

Controller

NI

782663-02 - NI

667 MHz Dual-Core CPU, 512 MB DRAM, 1 GB Storage, Zynq-7020 FPGA, Extended Temperature, 8-Slot CompactRIO Controller - The cRIO-9068 is a rugged, fanless, embedded controller that you can use for advanced control and monitoring applications. This software-designed controller features an FPGA, a real-time processor running the NI Linux Real-Time OS, and embedded user interface capability. The cRIO-9068 features an SDHC slot and a variety of connectivity ports, including two tri-speed RJ-45 Gigabit Ethernet, one USB host, and three RS-232 serial. Additionally, the cRIO-9068 supports an extended operating temperature range. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.

Product

NI-9962, 3-Pin 3.5mm Push-In Spring Terminal Block Plug

787104-01

Terminal Block

NI

787104-01 - NI

NI-9962, 3-Pin 3.5mm Push-In Spring Terminal Block Plug, Qty 4, With 26 Awg Ferrules, Qty 20

Product

MCX Male to BNC Male Cable, 50 Ohm, 30 cm

188375-0R3

Coaxial Cable

NI

188375-0R3 - NI

The MCX-BNC Coaxial Cable is used for modular instruments such as PXI switches. This cable is available in 1 m and 30 cm lengths.

Product

PXI MultiComputing Remote Control Module

Remote Control Interface

NI

NI

PXI MultiComputing Remote Control Modules enable PXI systems to transfer data at multigigabytes per second with only a few microseconds of latency. You can use these models in applications such as real-time tests, hardware-in-the-loop (HIL) tests, and structural tests that need a large number of distributed PXI systems to share data with low latency.

Product

PCI-8532, 1-Port, DeviceNet Interface Device

781062-01

Interface

NI

781062-01 - NI

The PCI‑8532 is a high-speed DeviceNet Interface for developing applications with the NI‑Industrial Communications for DeviceNet driver. DeviceNet is based on the controller area network (CAN) physical layer and increases strength and interconnectivity by specifying various parameters, such as the required cable length, connectors, and baud rates. The DeviceNet specifications are managed by OVDA, Inc. You can program the PCI‑8532 to add high-performance master/scanner or slave capabilities to DeviceNet networks.

Product

Expansion Module For CompactRIO

Module

NI

NI

The Expansion Module for CompactRIO connects to the processor I/O, such as USB and Ethernet, of a controller to expand its functionality. This module works with CompactRIO Controllers, Industrial Controllers, CompactRIO Single-Board Controllers, and PXI Controllers to expand the capabilities of the system, such as adding additional storage for saving more data and increasing the number of USB or time-sensitive networking (TSN) Ethernet ports of the system. Additionally, the Expansion Module for CompactRIO features the same rugged shock and vibration ratings as other CompactRIO modules, and you can can mechanically connect it to a controller for integration using mounting accessories.