Showing results: 901 - 915 of 1987 items found.
-
Micropross MP500 PT1-NFC -
NI
Support for ISO 14443 A/B, ISO 15693, MIFARE™, FeliCa™. Measurement correlation with NFC Forum and EMVCo certification test bench. Automated test executive with ready-to-run test sequences. Reader/Writer and Card Emulation modes, resonance frequency measurements supported on same antenna. Embedded analog measurements - LMA, field strength, S11, Q factor, waveform characteristics. Physical parameter/waveshape characteristic definition
-
SH68-C68-S / 186381-0R5 -
NI
Cable, 68-Pin VHDCI to 68-Pin .050 Series D-Type, 0.5m
-
SH68-C68-S / 186381-01 -
NI
Cable, 68-Pin VHDCI to 68-Pin .050 Series D-Type,1m
-
787058-01 -
NI
The acA720-290gc is a Color Basler Ace GigE Vision Camera with a 0.3 MP resolution and a maximum image acquisition speed of 290 frames per second. The acA720-290gc uses a IMX287 sensor and is quality tested and calibrated for high performance and reliability. This camera can be used with NI hardware and software to build machine vision systems.
-
787059-01 -
NI
The acA1440-73gc is a Color Basler Ace GigE Vision Camera with a 1.6 MP resolution and a maximum image acquisition speed of 73 frames per second. The acA1440-73gc uses a IMX273 sensor and is quality tested and calibrated for high performance and reliability. This camera can be used with NI hardware and software to build machine vision systems.
-
782145-01 -
NI
The acA2040-180kc is a Color Basler Ace Camera Link Camera with a 4 MP resolution and a maximum image acquisition speed of 180 frames per second. The acA2040-180kc uses a CMV4000 sensor and is quality tested and calibrated for high performance and reliability. This camera can be used with NI hardware and software to build machine vision systems.
-
782143-01 -
NI
The acA2000-340kc is a Color Basler Ace Camera Link Camera with a 2 MP resolution and a maximum image acquisition speed of 340 frames per second. The acA2000-340kc uses a CMV2000 sensor and is quality tested and calibrated for high performance and reliability. This camera can be used with NI hardware and software to build machine vision systems.
-
777598-01 -
NI
96-Channel, 5 V TTL/CMOS, 2.5 mA PXI Digital I/O Module—The PXI‑6508 uses four, 24‑bit programmable peripheral interfaces (PPIs) that can each be divided into three, 8‑bit ports. The PXI‑6508 can interface to peripherals or other computers, and it can operate in either a unidirectional or bidirectional mode and handshake with peripheral equipment. The PXI‑6508 is well suited for applications that require onboard pull-up resistors.
-
157867-02 -
NI
9-Pin D-SUB Male to Pigtail I/O Cable, 2 m
-
157867-01 -
NI
9-Pin D-SUB Male to Pigtail I/O Cable, 1 m
-
780041-01 -
NI
9-Pin Male D-Sub to 5-Pin Female Screw Terminal, Breakout for CAN Terminal Block - The CAN Breakout Box works with high-speed, low-speed, and single-wire controller area network (CAN) devices or PC interfaces. It features 14 ports for connecting devices with cables or directly to wiring harnesses. With an onboard power supply, the CAN Breakout Box can place power on the V+ pin required by some CAN transceivers. With a switch on the front panel, you can select 120 Ω, 60 Ω, or no termination on the network. You can use the CAN Breakout Box in desktop applications or mounted on a DIN Rail for test fixtures and cabinets.
-
781156-01 -
NI
8‑Slot, USB CompactDAQ Chassis - The cDAQ‑9178 is a CompactDAQ USB chassis designed for small, portable sensor measurement systems. The chassis provides the plug‑and‑play simplicity of USB to sensor and electrical measurements. It also controls the timing, synchronization, and data … transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The cDAQ‑9178 also has four 32‑bit general-purpose counters/timers. You can access these counters, as well as share clocks and triggers, through two built-in BNC connectors.
-
198290-01 -
NI
9-Pin, Female D-SUB to 9-Pin, Female D-SUB FlexRay Cable - The SHD9F-D9F FlexRay Cable connects FlexRay interfaces to devices, breakout boxes, other interfaces, and accessories. This cable meets FlexRay cabling specifications and is compatible with all NI-XNET FlexRay interfaces. It offers 82 dB/km attenuation with no termination. The cable’s impedance is 100 Ω, 148.94 Ω/km at 20 °C resistance, and 5.2 ns/m delay. The cable features four 26 AWG twisted pairs and dedicated pairs for FlexRay Bus A and Bus B.
-
182767-01 -
NI
24-Pin, Female GPIB (IEEE 488) to 24-Pin, Female GPIB (IEEE 488) Bulkhead - The GPIB Bulkhead connects GPIB cables to other accessories. NI offers it in Type XC and XD.
-
182766-01 -
NI
24-Pin, Female GPIB (IEEE 488) to 24-Pin, Female GPIB (IEEE 488) Bulkhead - The GPIB Bulkhead connects GPIB cables to other accessories. NI offers it in Type XC and XD.