Finna Sensors
Finna Sensors is fully dedicated to manufacturing continuous on-line moisture measurement and control systems as well as handheld portable moisture analyzers.
- 909-941-7776
- 5690 DTC Blvd.
Suite 550E
Greenwood Village, CO 80111
United States of America
-
Product
Model V: Veneer Moisture Meter
MRC003304
-
Calibrated for 48 hard and soft woods in the 0% - 25% moisture range and has dials for specific woods. Accurate to 1/8 inch penetration.
-
Product
Transverse Planer Moisture System
MC PRO 2400
-
Maximize grade recovery with Finna Sensors' highly accurate transverse planer meter. The most widely-adopted transverse sensor system acts as a dropout or easily integrates with auto graders. Integration via ProTrac software, with barcode or manual tracking, provides advanced kiln analysis and drying reports.
-
Product
Model B: Concrete Moisture Meter
MRC003305
-
Specifically designed for the concrete block industry. Includes calibrations for over 34 different kinds of concrete block. Direct reading scales for average percent moisture content.
-
Product
Model DG-9 (Universal Voltage)
DA8-G9-UNIV
-
Designed for semi-solids; powdered, granular or textile materials; and pliable sheets in rolls or stacks. Optional needle electrodes and sensitivity modules which allow for a wide range of moisture measurements. Rechargeable NiMH batteries save hassle and money of battery replacement.
-
Product
Model LG: Drywall Moisture Meter
MRC006505
-
Provides average moisture content down to a penetration of 1in. Uses radio frequency capacitance to measure the moisture content of gypsum wallboard. 0% - 25% moisture range.
-
Product
Model N8: Narrow Materials Moisture Meter
MRC001948
-
Designed for flat, curved, smooth, or rough surfaces such as cones or beams of yarn, rolls or stacks of cloth, and more. Electrode covers an area of 1 - 1/4 x 3 inches and penetrates 1/2 inch into the product.
-
Product
Model LP: Lumber & Plaster Moisture Meter
MRC006504
-
Offers the same ad the Model L plus spring-loaded electrode buttons for testing irregular, flat, and curved surfaces. Allows moisture comparisons between kiln decks. Tests 1/4" (6.4mm) to 3/4" (1.9cm) thick wallboard and plasterwork.
-
Product
OMNIR: On-Line Near Infrared Sensor
-
OMNIR is the future of near infrared moisture sensing technology. Coming from OMNI, meaning “all” and NIR, meaning “near infrared,” Finna Sensors has created an intelligent all-sensing solution that exceeds expectations. It not only delivers accurate data instantaneously and non-destructively, it also monitors its own health to perform its best during your crucial processing moments. By selectively harnessing light, to ensure increased uptime and greater profitability for your operation, the future of your manufacturing operation starts now.
-
Product
Lab Moisture Analyzer
-
PC-Based laboratory/production Moisture Analyzer connects through the RS-232 Serial Port. For nuts, granules, powders, pellets, chips or flakes. Complete with:– MCPC-RS Test Chamber– Windows PC-Based Software– Two Sample Cups– Dial Thermometer– Standard Block– RS-232 Cable (10 Feet)– USB to RS232 Adapter– Operating Instructions Manual– 115VAC/60HZ Wall Transformer
-
Product
Densigrader: Dynamic Weight Sorter
-
The Densigrader: Dynamic Weight Sorter is made for on-line mass/density measurements and sorting of green lumber prior to drying. The accurate mass and optional volumetric measurements provide an increase in grade recovery and kiln productivity. Its small footprint fits easily into most transverse, lugged transfer chains. System employs either RS232 or TCP/IP protocols to hand off data to sorting PLC.
-
Product
Model A8: All-Purpose Moisture Meter
N/A
-
Designed for flat, curved, smooth, or rough surfaces such as cones or beams of yarn, rolls or stacks of paper or paperboard. Covers 3" a diameter (7.6mm) and penetrates 3/4" (1.9cm). Reliable, long battery life. Includes a rechargeable battery, carrying case, and operating instructions book.
-
Product
Model LGF: Gypsum Moisture Meter
MRC006522
-
Stainless steel flat plate electrode. Excellent for testing Gypsum Wallboard as it moves or in stacks. Measures moisture in the Gypsum plasterboard 1/4 inch to 3/4 inch thick. Can also check moisture distribution pattern and length or width.
-
Product
Handheld Moisture Meters
-
Since water has a dielectric constant considerable higher than any other material, even a small amount of water in a product will cause the combination dielectric constant to increase substantially. Finna Sensors' capacitance meters can easily recognize this increase in water content and are programmed to display the result in direct reading percent moisture content.
-
Product
Model DC-2011: Cork Moisture Meter
DC-2011
-
Provides fast and accurate moisture read in 4% - 22% range. Durable plastic molded case, and includes Large LCD Display for easy reading. Reduces and eliminates factors such as cracked corks and poor cork compressibility, among numerous others. Product use reduces cork production error, increases efficiency, and thus increases profit.
-
Product
Inline Planer Moisture System
MC Pro 2500
-
Maximize grade recovery with SCSFP’s highly accurate lineal planer meter. A full moisture map of each piece ensures you are properly tracking moisture content at the planer. The system easily couples with lineal auto graders for moisture content handoff. Integration via ProTrac software, with barcode or manual tracking, provides advanced kiln analysis and drying reports.
