Showing results: 16 - 28 of 28 items found.
-
B-1005/6 -
ROSS ENGINEERING CORPORATION
*Three Phase*Upright or Low Profile for High Reliability*½ to 2 Cycle Trip & Interrupt*208V to 38kV Operate*200 to 1,200A Continuous*2,000 to 28,000A Interrupt*Line or Energy Storage Close & Trip*Ideal for High Power Electronics*High Speed Sealed Arc Interrupting*High Speed Crobar Shorting*Compact, Light Weight*Long Life*Minimum Reignitions*Minimum Restrikes
-
B-1022 -
ROSS ENGINEERING CORPORATION
AC QuietDC to 800HzClass B and H insulationExtendable strokeUniversal mountingHigher holding forceEnvironment resistantOptional electronic controller* *Allows vibration free operation *Prevents coil burn-out *Provides DC-800Hz capability without heat producing dropping resistors *Optional Computer Controlled with 4-10V 5mA signal
-
B-1009 -
ROSS ENGINEERING CORPORATION
The Step-Start Vacuum Circuit Breaker/ Power Controller is designed for extra heavy duty repeated fault, crobar and load interruption for sensitive equipment. It is designed to limit initial closing inrush current to approximately load or other maximum current with an adjustable step delay.
-
B-1027 -
ROSS ENGINEERING CORPORATION
Ross Engineering Corporation’s High Voltage Calibration Lab provides high accuracy capability for conducting tough reliability tests on all our high voltage devices. In this facility we test and calibrate HV Relays, HV Dividers, HV Probes, Spark Gaps, our Fiber Optic Systems, and HV Digital Voltmeters up to 450kV. We provide our own in house test lab to ensure Ross products meet or exceed required safety standards as well as our own high standards of dependability, long life and quality. Our technicians use test equipment calibrated by or traceable to National Institute of Standards and Technology or other national metrology institute to provide the highest in testing accuracy.
-
B-1013-6 -
ROSS ENGINEERING CORPORATION
Ross Engineering Corporation’s High Voltage Megmeter® series are unique battery powered DC hipot tester and meter. Models are available for withstand testing of insulation up to 50kV DC, as well as measuring leakage current as low as 0.001 microamp and resistance as high as 30 million megohms when testing underground cable, rubber safety gloves, vacuum interrupters, high voltage devices and all types of electrical insulation. All models have an over current trip feature to minimize arcing damage. Completely portable with rechargeable 12V battery which can be recharged from an automobile or 115V, 230V AC.
-
B-1020-B -
ROSS ENGINEERING CORPORATION
Ross Engineering Corporation has developed a HV compact analog fiber optic transmitting and receiving system, with optional over-voltage limiting, designed to drive instrumentation from a DC to 1MHz signal source. The system is available with optional multiple input and output ranges of ±0-1V PK, 0-5V PK to 0-10V PK. It will also operate in conjunction with Ross Engineering Corporation’s high accuracy high voltage wideband voltage dividers, which are useful from DC to over 10MHz up to 1,000,000V PK at 0.01% to 3% accuracy. Transmitters and receivers can be powered by either AC or DC.
-
B-1026 -
ROSS ENGINEERING CORPORATION
Ross Engineering Corporation has developed and manufactures a line of Electrostatic Discharge (ESD) testers. One model is designed for explosive proof testing per MIL-I-23659C, Paragraph 4.4.3.2 static discharge test. It incorporates high voltage electro magnetic or air pressure operated relays to safety ground, charge, and dump capacitors into the appropriate device under test. This ESD tester is a portable system utilizing 120V AC power. It is a high reliability device capable of many thousands of cycles.
-
B-1020 -
ROSS ENGINEERING CORPORATION
*Wideband: DC to over 30MHz*Maximum Output: to 10V PK, 20V PK-PK*Maximum Input: ±5V to ±200V PK-PK as required. Also to 900kV PK with Ross Voltage Divider*Signal Isolation: 500,000 Ohm 450V PK*Input Impedance: Up to 2 Megohms*Load Impedance: 50 Ohm or greater*Power Source: AC or Optional Battery*Will drive over 500 Feet of Coaxial Cable
-
B-1023-G -
ROSS ENGINEERING CORPORATION
Specifically designed for Calibrating High Voltage Measurement Devices or Testing High Voltage Equipment, Insulation & High Voltage Interrupters or other High Voltage Vacuum Devices.
-
-
B-1004 -
ROSS ENGINEERING CORPORATION
*1kV to 300kV DC/AC PK Test*1A to 2,000A Continuous*2,000 to 28,000 amp AC Interrupt*20A DC Interrupt*High Speed Stored Energy Closing and Opening*1 to 20 millisecond Operate Time*NC, NO, DT, or Latching types available
-
B-1001-M -
ROSS ENGINEERING CORPORATION
*Used to develop pulse forming networks.*14 pulse per 1.5 sec or other.*In accordance with aircraft test specs: RTCA/DO-160E or Boeing D.6-16050-5 or others.
-
B-1011-G -
ROSS ENGINEERING CORPORATION
For limiting, setting or indicating voltage levels of power supplies, required charge level for energy storage capacitors, and voltage level interlocking.