VEGA Grieshaber KG
VEGA is a global manufacturer of level measurement sensors, point level switches and pressure transmitters.
- 513-272-0131
- 513-272-0133
- americas@vega.com
- 3877 Mason Research Pkwy
Mason, OH 45036
United States of America
-
Product
Indicating Instruments
-
In continuous level measurement, the filling height in a vessel is repeatedly detected. The measured value is further processed, e.g. as a 4 … 20 mA signal in a PLC or process control system. Indication of the measured value directly on site is also frequently requested.
-
Product
Pressure
-
Pressure transmitters measure process pressures as well as the levels of liquids, gases and vapours.
-
Product
Components
-
Electronic devices and circuits that manipulate, transform, and refine sensor signals to make them suitable for measurement, recording, or control systems.
-
Product
Overvoltage Protection Instruments
-
Safety devices designed to protect sensitive electrical equipment from voltage spikes, surges, or sustained excessive voltage.
-
Product
Flow
-
In flow measurement, the amount of material that flows through a certain pipe cross section per time unit is measured.
-
Product
Capacitive
VEGACAL
-
In capacitive level measurement, the sensor and the vessel form the two electrodes of a capacitor. Any change in level causes a capacitance change, which is in turn converted into a level signal.
-
Product
Capacitive Level Switches
VEGACAP, VEGAPOINT
-
In capacitive point level detection, the sensor and vessel form the two electrodes of a capacitor. Any capacitance change caused by a level change is converted into a switching signal. Thanks to the shortenable cable and rod versions, level switches can be perfectly adapted to any application. They are often used for overfill or dry run protection as well as oil/water or foam detection.
-
Product
Level Measurement
-
In continuous level measurement, the level of a medium in a tank or silo is detected with the help of different measuring methods and converted into an electronic signal. The level signal is either displayed directly on site or incorporated into a process control or management system.
-
Product
Interface Measurement
-
Interfaces, that is, boundaries between separation layers, can be found everywhere in the process industry, e.g. in the chemical or oil & gas industry. An interface arises when two media with different densities are filled into a container: for example, water and oil. To separate the two media from one another, it is necessary to determine where the transition from one medium to the other is located. VEGA sensors can be used to measure both the total level and the interface reliably.
-
Product
Differential Pressure (Flow)
VEGADIF
-
In flow-rate measurement via differential pressure measurement, the differential pressure is measured with the help of a differential pressure device, e.g. an orifice plate or a dynamic pressure probe (pitot tube). The differential pressure transducer calculates the flow rate from the measured value provided by differential pressure system. Thanks to the finely graduated ranges of the measuring cells and the minimal measurement deviation, very accurate flow-rate measurement can be realized.
-
Product
Vibration
VEGASWING, VEGAVIB, VEGAWAVE
-
In point level measurement with vibrating level switches, a rod or a fork is set vibrating. When the vibrating probe comes into contact with the medium, the vibration changes and the vibrating level switch outputs a switching command. Vibrating level switches are used as overfill protection devices or low-level indicators in liquids as well as in granular and powdery bulk solids.
-
Product
Guided Wave Radar (GWR)
VEGAFLEX
-
In level measurement with guided wave radar, microwave pulses are conducted along a cable or rod probe and reflected by the product surface. The measuring probe of the TDR sensor ensures that the signal reaches the medium undisturbed. Liquids, bulk solids and separation layers (interfaces) in liquids are commonly measured with this measuring technique.
-
Product
Microwave Barrier (Radar)
-
The microwave barrier functions like a light barrier: when the medium gets in the way of the microwave beam between the transmitter and the receiver, the signal is attenuated. This change is detected by the receiver and converted into a switching signal.
-
Product
Electronic Differential Pressure
Density Measurement
-
An innovative software and hardware concept makes it possible to combine any two pressure transmitters of the VEGABAR 80 series into an electronic differential pressure system to measure density. Electronic differential pressure measurement is used for measuring density change and/or for compensation when the level needs to be measured.
-
Product
Process Pressure
VEGABAR
-
Pressure transmitters measure the pressure of liquids, gases and vapours in pipes or closed vessels. The pressure of the measured medium acts on a pressure measuring cell, which converts it into an electronic signal.The process pressure transmitters are ideal for detecting the relative or absolute pressure in applications with condensation or rapid temperature changes.
