Showing results: 46 - 60 of 181 items found.
-
ZET 7174 -
ZETLAB Company
*Interface converter USB↔CAN 2.0*Digital sensors and controllers power supply*Data exchange with PC
-
ZET 7076 -
ZETLAB Company
Previously it was widely thought that it is enough to receive sensor readings and to have remote control over them. But gradually there evolved a need for remote control, i.e. people need to receive sensors readings and to control their performance via Internet (for instance, on a portable device). Such possibility simplifies quite a lot of tasks since one can control performance of a system located at the other end of the city or even a country.
-
Tachometer -
ZETLAB Company
Tachometer is used for measuring the rotation frequency of shafts in machines and mechanisms, as well as for calculating the number of complete revolutions. Typically, for measuring the rotation frequency, optical or induction rpm sensors are used.
-
AC Selective Voltmeter -
ZETLAB Company
AC Selective Voltmeter is used for measuring AC voltage coming to the input channels of ADC modules and FFT spectrum analyzers. The specific feature of the AC selective voltmeter is perfomance of voltage measurements on the main signal-carrier frequency, which allows to eliminate the harmonics influence on the readings.
-
Multichannel Strain Gauge Meter -
ZETLAB Company
The Software Multichannel strain gauge meter is used for performing all types of strain gauge measurements using strain gauge sensors (for instance, force and torque sensors, bridge and semi-bridge circuits based on resistive strain sensors), strain measurement data acquisition modules ZET 017-T and digital strain gauge sensors of ZETSENSOR series. The program enables simultaneous processing of up to 128 measuring channels using strain gauge station and up to 500 measuring channels in the case if digital sensors are used.
-
Vibration Meter -
ZETLAB Company
The input signal of the Vibration meter software, which is the output signal of the accelerometer, i.e. the vibrational acceleration signal, is filtered by means of one of four possible digital band filters. Then, based on this signal, vibrational velocity and displacement signals are calculated by means of integrating filters. Thus, the software generates three signals which are transferred to the ZETLAB data server virtual channels created by the program and having the word “Acceleration”, “Speed” or “Displacement” in their names, respectively.Signals are averaged for a selected time interval (0.1 s, 1 s, or 10 s), after which the obtained values are displayed in the dialog box elements of the Vibration meter program. It is possible to display a root-mean-square (RMS), average amplitude or peak value.
-
Power Meter -
ZETLAB Company
Power Meter is used for determining the power of the electrical current coming to the input channels of ADC modules and FFT spectrum analyzers, or that of the electromagnetic signal.
-
DC Voltmeter -
ZETLAB Company
DC Voltmeter is used for measuring DC voltage coming to the input channels of ADC modules and FFT spectrum analyzers. The indicator displays the DC voltage mean value and root-mean-square deviation (RMSD) from the mean value of the selected channel signal. It is possible to change the averaging of the displayed value (0.1; 1, or 10 s) and to select a necessary channel of the ADC module and FFT spectrum analyzer or a virtual channel.
-
Phasemeter -
ZETLAB Company
Phasemeter is used for measuring the phase difference of two signals coming to the input channels of FFT spectrum analyzers. The upper line of the indicator displays the current phase difference value in degrees, the lower line – phase difference value in radians. It is possible to change the averaging of the displayed value (0.1 or 1 s) and to select necessary FFT spectrum analyzer channels.
-
AC Voltmeter -
ZETLAB Company
AC Voltmeter is used for measuring AC voltage. The software is capable of switching measurement modes (RMS or amplitude), but regardless of the selected mode the information about the current peak value is always displayed.
-
Frequency Meter -
ZETLAB Company
Frequency Meter is used for measuring the frequency of the signal coming to the input channels of ADC modules and FFT spectrum analyzers. The indicator displays the measured frequency value (frequency of periodic oscillations) and signal cycle time corresponding to the measured frequency. It is possible to change the averaging of the displayed value (0.1; 1, or 10 s) and to select a necessary channel of the ADC module, FFT spectrum analyzer or a virtual channel.
-
Torsiograph -
ZETLAB Company
Torsiograph is used for measuring the rotation non-uniformity in rotating parts of various mechanisms. Torsiograph generates virtual channels for displacement and displacement velocity. These channels are available for further analysis by ZETLAB programs, e.g. for displaying on the oscillograph.
-
Encoder -
ZETLAB Company
Encoder is used for measuring the relative position (displacement), displacement velocity and direction by means of optical angular or linear displacement sensors (encoders) connected to the ADC input channels.
-
ETHERNET Connection -
ZETLAB Company
There is a utility for connecting several devices via Ethernet, which checks if there are any Ethernet devices and provides point-to-point connection to all selected devices simultaneously.
-
Signal Transmitter (Data Server) -
ZETLAB Company
The program is used for transferring ZETLAB digitalized signals through the network. As soon as the data server is turned on, any computer in the same subnetwork can connect to it via the program Signal Receiver (Data Client) – and all signals of the server computer appear in its channel list. Then, it does not matter whether these signals are processed by the server computer or a computer to which they are coming via the Data server → Data client system.
