PMC Modules
-
product
PMC Modules
ARINC 429
Sycos range of ARINC 429 PMC modules offer the user up to 32 channels on a single width PMC module. Each channel can be programmed independently to operate at either high or low speed. Firmware options available for Tx Error Insertion and Rx Error Reporting are available.
-
product
PMC Module
PMC-1553-TACEx
Operating temperatureCommercial: 0 to +70 °COptional: -40°C to +80°C• Airflow requirement: .5 CFM• Humidity: 5 to 90% (non-cond.)• Altitude: 0 to 20’000 ft
-
product
VME Generic Carrier Card For Conduction Cooled PMC(PCIbus Mezzanine Card) Modules
AVC-2-CC
VME64x (6U) generic carrier card for conduction cooled PMC (PCIbus mezzanine card) with 2 PMC slots. Modular solution combines any AIM conduction cooled PMC module for ARINC429, MIL-STD-1553 or any conduction cooled 3rd party PMC module.
-
product
LVDS I/O Module
LVDS-MOD3
Curtiss-Wright Defense Solutions
The LVDS-MOD3 is a front panel mezzanine module designed to provide LVDS I/O functionality to Curtiss-Wright's FPGA-based processing PMC modules. This LVDS I/O module provides 32 differential pairs to the front panel. The LVDS-MOD3 LVDS I/O module is aimed at embedded application development.
-
product
PMC Module
PMC-DA816
The PMC-DA816 is a slave Digital to Analog boardthat is managed by the host processor on the PMCbus. The card contains a state machine that performsmost of the work of outputting data, in order tominimize the impact to the HOST system.The PMC-DA816 is supported by ALPHI Technologyunder Windows NT by a Board Support Packagewhich is supplied with the card. Other documentationsupplied with the card will describe this support in fulldetail.
-
product
Interface
RCNIC-A2PA3
The RCNIC platform is a high performance, 3U CompactPCI module (PMC on carrier card) for the AFDX/ARINC 664 protocol. With two independent ports for traffic monitoring, traffic generation, external triggering and analysis, the RCNIC provides high-resolution time-tagging of incoming packets simultaneously with highly accurate traffic generation. An IRIG-B receiver/generator is included for synchronization to an external IRIG-B time source and for synchronization between multiple RCNIC boards.
-
product
PMC Module With 2 Or 4 CAN Bus Nodes ARINC825 Compliant For Testing & Simulation Of Avionic CAN Bus Systems
AMC825-x
ARINC825 (CAN bus) Test & Simulation module for PMC with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The AMC825-x PCI Mezzanine Card (PMC) can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
product
PMC Carrier for 3U CompactPCI
TCP270
The TCP270 is a standard 3U CompactPCI carrier that provides front I/O and rear I/O for a single width PMC module. This PMC to 3U CompactPCI adapter is used to build modular, flexible and cost effective I/O solutions with PMC devices in CompactPCI systems.
-
product
32x ADC, 16x/0x DAC & 8x Digital I/O PMC Module
TPMC533
The TPMC533 is a standard single-wide PCI Mezzanine Card (PMC) compatible module providing 32 channels of simultaneous sampling true differential bipolar 16bit analog input, 16 or no channels of simultaneous update single-ended unipolar/bipolar 16bit analog output and 8 channels of tri-state 5V-tolerant TTL digital input/output. All signals are accessible through a HDRA100 type front I/O connector.
-
product
Mezzanine Module
RS485-MOD2
Curtiss-Wright Defense Solutions
The RS485-MOD2 is a front panel mezzanine module designed to provide serial I/O functionality to Curtiss-Wright FPGA-based processing PMC and XMC modules including the PMC-FPGA03, PMC-FPGA05 and XMC-FPGA05D. This RS485 I/O module provides 33 channels of EIA-485 or EIA-422B serial I/O. Each channel is configured as an input or output. The serial protocol and timing are handled by the host FPGA.
-
product
CompactPCI
3U PMC Carrier
This conduction cooled 3U CompactPCI single slot PMC provides an active interface between the CompactPCI bus (backplane) and a PCI Mezzanine Card (PMC). This product addresses the needs of aerospace, military, and rugged applications. It contains a thermal heat frame made of aluminum that fits together with conduction cooled PMC modules. Conduction cooling conducts heat away from the hot spots of the board and transfers the heat to the card edges and to the system chassis. No active ventilation is necessary inside of the system, which means the boards are sealed from the environmental influences found outside of the chassis. The heat frame and integrated wedge locks for the conduction cooling stiffens carrier and PMC module enabling the board to resist high shock and vibration.
-
product
MIL-STD-1553 A / B Test And Simulation PMC Module
PMC-1553
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems*Heat sink and / or protective coating available*Optional input / output for front panel
-
product
PMC Carrier Module
DP-VME-5114
DP-VME-5114 is a VME-Based PMC Carrier Module. This 6U VME board PMC carrier can accommodate two PMCs. This board can be used for data acquisition, automated testing and checkout systems
-
product
Others – Carrier Modules
To complement the wide range of interface modules for dedicated Avionics Databuses and Networks, AIM offers a range of Carrier modules for the use of AIM or any 3rd Party PMC and XMC module on various backplanes.
-
product
Interface
RP-708
The RP-708 is a two-channel ARINC 708 weather radar display data bus PMC module interface, supporting variable frame sizes for embedded applications, simulation and test. Abaco Systems provides integrated support for this module on PCI, PCIe, CompactPCI, VME, VXI and native PMC platforms. Each RP-708 channel can be configured as two transmit channels, two receive channels, or one transmit channel and one receive channel simultaneously.
-
product
PMC Module
PMC-601
Curtiss-Wright Defense Solutions
The PMC-601 PMC module allows customers to incorporate MIL-STD-1553 and discrete digital I/O connectivity into military and aerospace embedded computing systems. We assure an easy integration with other elements of our product lines, as well as after-sales technical support, life-cycle management services, and the commitment to long-term availability.
-
product
6U Dual 64/100 PMC VME Carrier
V2PMC2
The V2PMC2 PCI-X/PMC carrier card is a 6U VME that holds up to two single-width or one double-width PCI-X/PMC modules. The V2PMC2 works in association with a PCI-Express host which is connected to it through a x4 PCI-Express serial link onto P0 connector.
-
product
PMC-BiSerial II-NG1
The PMC BiSerial-II NG1 is part of the PMC Module family of modular I/O components by Dynamic Engineering. The PMC BiSerial-II is capable of providing multiple serial protocols. The NG1 protocol implemented provides two full-duplex RS-422 UART interfaces with error detection, two half-duplex RS-485 custom "index" interfaces, external clock input, two clock outputs, and various discrete signal inputs and outputs, all using RS-485 transceivers
-
product
Mezzanine Cards
PMC and XMC are the quasi standard for mezzanine cards in VME systems. esd's PMC and XMC modules extend your system with a bus interface (CAN, EtherCAT, Ethernet) or an intelligent sub system (e.g. XMC-CPU/2041, PMC-CPU/440). Furthermore esd develops customized PMC and XMC modules. VME systems without PMC slot can be extended with an esd VME-PMC-Caddy or PCIe-XPIMC-Carrier board.
-
product
PMC Module Carrier
SK1-CHORD
SK1-CHORD is equipped with a PCI Express® to PCI® bridge for conversion of data from the CompactPCI® Serial backplane, to the on-board PCI® parallel bus.
-
product
6U Form Factor PMC/PrPMC Carrier-VMEbus
i4400
The i4400 is a low-cost 6U form factor PMC / PrPMC carrier for the VMEbus and forms the basis of a flexible I/O system. It offers the user a means of integrating two single PMC modules or one double PMC module in a VMEbus system. The current version of the i4400 supports PMC modules and also supports Processor PMC modules on one PMC-site. The VME-to-PCI bridge is implemented in an FPGA for flexible VME-to-PCI mapping and to allow future updates and upgrades.
-
product
PMC Module
PMC-softDAC
2 µS settling time, 0-5v range• Six Programmable OutputRanges per channel• Unipolar: 0V to 5V, 0V to 10V• Bipolar Mode: ±5V, ±10V,±2.5V,–2.5V to 7.5V• 1LSB Max DNL and INL Over theIndustrial Temperature Range• 64k DAC buffers• Power-On Reset to 0V• Flash ram for configuration file• Two stage buffers• Global output buffer w/ internal orexternal triggering
-
product
ARINC825 Cards
AIM’s ARINC825 cards can work either with full functionality as an active CAN node for testing and simulating or in listening only mode for monitoring and recording purposes of Avionic CAN bus (ARINC825) applications on up to 4 electrically isolated CAN bus nodes concurrently. All nodes are in conformance with the ISO11898-1/-2 standard. They are accessible by software separately and can be used as 4 independent CAN bus nodes. An onboard IRIG-B time decoder allows users to accurately synchronize single or multiple modules to a common time source. All supported signals are available through front I/O and rear I/O interface. ARINC825 cards consist of FPGA based CAN interface controllers as well as a FPGA based 32-bit microcontroller core and a separate processor for IRIG-B synchronization with high resolution time stamping. All nodes are operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s with the intelligence to process scheduling of CAN frames in real time onboard to significantly off-load the host processor.For embedded applications the AMC825-4 PMC module is available in a conduction cooled version. Using AIM’s family of PCI, CPCI (3U and 6U) and VMEbus carrier cards for PMC our clients have off the shelf solutions in a broad range of card formats. ARINC825 (CAN bus) modules are delivered with an Application Programming Interface (API) and Driver Software compatible with Windows, Linux and VxWorks.An ARINC825 Resource Component is available for AIM’s PBA.pro™ databus test and analysis tool including Tx and Rx simulation capabilities, a Chronological Bus Monitor and support for decoding of payload data within CAN messages. This allows to implement a powerful ARINC825 (CAN bus) analyzer or a complete test system in conjunction with other AIM avionics databus interfaces and PBA.pro™ supported 3rd party hardware.
-
product
PCIe Carrier For PMC And PrPMC
PCI104
The PCI104 is a PCIe carrier for PCI Mezzanine Cards (PMC) or Processor PCI Mezzanine Cards (PrPMC). The PCI104 carrier allows simplified testing of PMC/PrPMCs and their associated PMC I/O Modules (PIMs) by using a PC environment during board development or deployment. The PCI104 can also reduce the costs of manufacturing PMC/PrPMCs by allowing manufacturers to use off-the-shelf PCs for functional testing. The PCI104 converts the PCIe x4 edge connection to PCI-X via a PCIe to PCI-X bridge. The trace lengths to the PMC/PrPMCare kept to a minimum so the PMC/PrPMC can run with a133MHz PCI-X clock speed. The J4 connector of the installed PMC/PrPMC is routed to a 96-pin DIN connector per theVITA-35 specification. The PCIe to PCI-X bridge can run in either transparent or non-transparent mode and can also operate in forward or reverse mode. The PCI104 has a fan mounted on the board to cool the PMC/PrPMC. The fan can easily be removed for testing and probing of hosted card.
-
product
Interface
RCNIC-A2PAX
The RCNIC platform is a high performance, PCI module (PMC on carrier card) for the AFDX / ARINC 664 protocol. With two independent ports for traffic monitoring, traffic generation, external triggering and analysis, the RCNIC provides high-resolution time-tagging of incoming packets simultaneously with highly accurate traffic generation.
-
product
PCI Express PMC Carrier
TPCE260
The TPCE260 is a standard height PCI Express Revision 1.1 compatible module that provides one slot for a single-width PMC module used to build modular, flexible and cost effective I/O solutions for all kinds of applications like process control, medical systems, telecommunication and traffic control.
-
product
PMC-to-PCI Express Adapter
4733
The Technobox, Inc. P/N 4733 PMC-to-PCI Express Adapter permits the use of a single-wide PMC module in a 4X PCIe slot. The product features a PEX8114 bridge running in transparent mode. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card. 64-bit support.
-
product
PMC to 3U CompactPCI Carrier
7000
This low-cost family of CompactPCI adapters enables the use of standard and custom 32-bit based PMC modules in a 3U or 6U CompactPCI system.
-
product
PMC Module
PMC-1553
Operating temperatureCommercial: 0 to +55 °COptional: -25°C to +80°C• Non-operating: -40°C to 85 °C• Airflow requirement: .5 CFM• Humidity: 5 to 90% (non-cond.)• Altitude: 0 to 10’000 ft
-
product
CompactPCI
6U PMC Carrier
This conduction cooled 6U CompactPCI dual slot PMC provides an active interface between the CompactPCI bus (backplane) and a PCI Mezzanine Card (PMC). This product addresses the needs of aerospace, military, and rugged applications. It contains a thermal heat frame made of aluminum that fits together with conduction cooled PMC modules. Conduction cooling conducts heat away from the hot spots of the board and transfers the heat to the card edges and to the system chassis. No active ventilation is necessary inside of the system, which means the boards are sealed from the environmental influences found outside of the chassis. The heat frame and integrated wedge locks for the conduction cooling stiffens the carrier and PMC module enabling the board to resist high shock and vibration.
