Networks

The OWM is a cost-effective solution for optical monitoring of DWDM networks including DWDM optical power, wavelength, and OSNR. The OWM available in 50 GHz or 100 GHz configurations with up to 8 ports. The OWM is the first shelf-level, intelligent sub-system for centralized management of remote DWDM wavelengths that can also be used as a port ...more

The Sat Buddy 2 sat finder measures relative RF signal strength when connected to a dish antenna. It's great for aligning a dish antenna to receive maximum signal strength, and for verifying signal presence within the in-house cabling network. ...more

The NPRT 2200 performs Noise Power Ratio measurements to determine the dynamic range of optical transmitters, amplifiers and other active devices used in HFC networks. It has an internal broadband noise source, selectable filters and a measuring receiver. ...more

ADSL Tester - GAO311 ADSL Tester - Function Physical layer test Network layer test Emulate PCADSL Modem ...more

The Noyes M200 from AFL Telecommunications offers unmatched OTDR capabilities in a handheld package weighing less than 1 kg (2 lb). Multimode, Single-mode, and Quad wavelength models are offered. With short dead zone and intermediate range specifications, the M200 is ideal for Tier 2 testing of premises (building and campus) networks or certif ...more

The ONA 600 Optical Network Analyser is a powerful and versatile tool for characterisation of optical fibers and networks. The system consists of a mainframe, plug-in modules for measurement of Chromatic Dispersion, Polarization Mode Dispersion and Spectral Attenuation with a full range of optical light sources. Designed to deliver superior pe ...more

FCST08221 Mini optical light source is the most rugged size instrument in the industry. It integrates the super small size and strong function in one unit. With 3 pieces of 1.5v alkaline batteries, can work 40 hours continuously, the total weight is only 80g .Together with FCST08221 Mini optical power meter, they provide a excellent solution f ...more

Serial Data Acquisition and Control Board. Provides Analog I/O, Digital I/O, Relay Driver Outputs and Temperature Measurements. RS-232, RS-422 and RS-485 Serial I/O includes network address and network packet modes. ...more

UltraScope Software introduces a family of Windows 95, 98, 2000, NT, and Windows XP applications that connect your GAODS2000 series oscilloscopes to your PC desktop by USB, RS-232 or GPIB (IEEE 488.2). Use Data Browser to display captured waveforms, data and measurement. Use DSO Controller to control the oscilloscope locally or over the networ ...more

The Hurricane II IP network emulator provides wan emulation and network simulation. The Hurricane II emulates any network condition in a repeatable and controllable lab setting. To re-create any network condition, the emulator can impair IP and non-IP traffic, provide dynamic, time-varying impairments, and use a fully independent and flexible ...more

The Sat Buddy sat finder is a satellite signal meter that measures relative RF signal strength when connected to a dish antenna. It's great for aligning a dish antenna to receive maximum signal strength, and for verifying signal presence within the in-house cabling network.  ...more

Complete more installs faster and better using the Super Buddy satellite finder meter. Be "sure of your bird" with the positive ID feature or use the automatic scan to identify the unknown satellite. The Super Buddy's geo-sensitive "Field Guide" shows you just the birds visible to your install -- ALL of them, with their ind ...more

The Noyes OLS7-FTTH and OLS7-3 laser sources from AFL Telecommunications are cost-effective, rugged, handheld instruments designed for performing insertion loss measurements on single-mode fiber optic links when used with an optical power meter. When paired with an optical fiber identifier, both models may be used for fiber identification. The ...more

The Noyes OPM5 optical power meter from AFL Telecommunications may be used to measure optical power in Premises, Telco, or Broadband fiber optic networks. When used with an LED or Laser light source, the OPM 5 also measures insertion loss of multimode or single-mode cables. The OPM5 offers Wave ID, automatic wavelength identification and switc ...more

Toronto, ON - GAO Tek Inc. has released a series of small form factor pluggable optical transceivers (XFP), which are fully compatible with Extreme’s original products. XFP modules support 10 Gigabit Ethernet IEEE standard interfaces as 10GBASE-LR, 10GBASE-ER and10GBASE-SR. Since the introduction of 10 Gigabit Ethernet, there has been a steady inc ...more

The 230A tests thin Ethernet (BNC), 10BaseT (UTP/STP), 100BaseTx, RJ45, TIA 568A, TIA 568B, and Token Ring cables within a few seconds. It detects miswiring, polarization, and continuity. The 230A also tests the ground of shielded twisted pair cables. With the remote unit, you can remotely test installed cable either from the wall plate or pat ...more

The 231A can easily read the correct pin configuration of 10BaseT cable (category 5), 100BaseTx, 10Base2 cable (coax) and RJ45/RJ11 modular cables, 356A, TIA 568A, TIA 568B and Token Ring cables by comparing one transmitting end to the corresponding receiving end. With the remote kit, it can test cables installed far away either on wall plate ...more

MSRP $175.00 The model 206 cable tester is a stand alone test device. It is designed to test popular PC data cables, printer, monitor, modem, mouse extension, game, BNC coax, RJ45, 1394, and USB cables by identifying the wire connection status: open, short, cross, miswire, and continuity of wires and pin configuration. It is a very good tool f ...more

The SuperLooper™ Ethernet Loopback Jack and Plug quickly and easily checks the RX/TX pairs of 10/100base network cables, helping a network technician determine if a network signal exists or if there are broken or shorted wires within the cabling (See Specifications). It can be plugged directly into an Ethernet wall port or can be attached to the en ...more

Odyssey Technical Solutions’ home office is a state of the art repair facility located in Round Rock, Texas. Our engineering staff consists of highly skilled professionals working in a meticulously maintained facility. We specialize in RF Generators, Automatch Networks, and Microwave Generators / Power Supplies. Our reputation for quick turnaround ...more

The Smartronix LinkUp? Ethernet Tester will provide the first response for troubleshooting network connectivity problems. The unit’s LEDs provide instant basic connection status. The LCD display allows more detailed link analysis through the menu system. Auto-negotiation capabilities can be scrolled through. Power-Over-Ethernet voltages can be read ...more

The Patch Test quickly tests Ethernet patch cables for continuity and common wiring standards such as Gigabit Ethernet, Fast Ethernet, and fast Ethernet Crossover. Remote testing of longer cables whose ends are not co-located can be accomplished by using a Smartronix Gigabit SuperLooper Loopback jack to test for Gigabit and Fast Ethernet cables in ...more

Power over Ethernet (PoE) Tester, connected to an RJ-45 outlet, tests the cabling infrastructure for the presence of power, either IEEE802.3af standard compliant or pre-standard. The PoE Tester identifies the existence and type of Power Sourcing Equipment (either Endspan or Midspan) in your network. ...more

The INAP Signaling Tester is a test environment for the INAP (Intelligent Network Application Part) signaling specification as defined by the ETSI and ITU-T standards. It is a SAFIRE based test harness able to run pre-defined ACATS test scenarios against INAP test objects in a controlled & deterministic manner. ...more

Anue CPRI Signal Delay Network Emulators simulate the impairments that can occur on a CPRI link. Like all Anue emulators it is supported by a flexible hardware platform that enables very accurate and highly repeatable testing and includes automation capabilities to increase testing efficiency. The CPRI Signal Delay Network Emulator can emulate ...more