Net Probes

Network tester: consists of a tone generator and a probe. Method: use the tone generator and the probe to determine where a cable is going and whether or not (and where) the cable is interrupted. Signal viewing in 3 modes: lamp (L), speaker (SP) or both (S&L). ...more

TRENDnets TC-TP1 is an easy-to-use amplified inductor and tone probe that is used for tone tracing and line testing. The TC-TP1 features a simple push button that provides easy operation and conserves battery power. This ergonomically designed device comes with adjustable volume control and signal LED for enhanced accuracy in noisy environmen ...more

The IntelliTone Pro Toner and Probe Series from Fluke Networks is the first toner and probe to offer digital and analog signaling all in one tool.  That means it's equipped with the most powerful cable location technologies for any work environment.   ...more

The Pro3000 Analog Tone and Probe is your best choice for toning and tracing wire on non-active networks, and specifi­cally for identifying individual pairs with SmartTone® technology. Angled bed-of-nails clips allow easy access to individual wires, and the RJ11 connector is ideal for use on telephone jacks. The large loud speaker on the probe allo ...more

Monitor your entire network through a single console interface by deploying software probes throughout your enterprise. Whether you have many remote offices or multiple network closets, Network Instruments probes offer complete access to remote data without the time and expense of travel. Software-based probes are installed on a LAN, wireless ...more

Tone tracing probes designed specifically to meet the needs of organizations operating large copper networks and in particular those who are committed to improving service delivery and reducing whole life costs. ...more

Provides precise cable measurements while it thoroughly probes network lines for faults. ...more

The tone generator sends a trace tone and the probe detects the signal. ...more

NetWisdom software is an Enterprise Storage Area Network assurance solution that provides the deepest level of fibre channel SAN traffic and fabric monitoring available. NetWisdom, combined with SAN probes and TAPs collect metrics about underlying SAN protocol and data traffic to provide performance and fault detection at the packet level accu ...more

The pen-size Network Tone Probe, an inductive receiver, emits its locator tone when it touches the tip of the wire or even just the jacket. ...more

ScanINSPECT FPT is a flying probe electrical tester suitable for fixture-less bare PCBs. It can also be used in combination with a grid tester for fault verification or to test nets exceeding test points of a grid tester. Software runs on Windows XP. The tester is fast, easy to use, very reliable and easy to maintain.  ...more

Network Instruments’ Probe Appliance for 10/100 networks was designed to monitor activity at the edge of the network. By deploying the 4U Probe Appliance for 10/100 networks, you can monitor up to four remote links in real time from any location, saving valuable time and money that would otherwise be spent flying out an administrator to those sites ...more

Troubleshoot and document your WAN circiuts without leaving your desk. WAN Probes offer complete inline monitoring, decode and statistics for WAN traffic, as well as all payload data, at links up to DS3/T3/E3 speeds. As with all Network Instruments Probes, WAN Probes report to any (external) Expert Observer or (external) Observer Suite co ...more

Troubleshoot and document local or remote gigabit segments without leaving your desk. Network Instruments offers both Hardware and Software-based Probes to accommodate all network speeds and specific network configurations. Hardware-based Probes are specific to administrators that require wire-speed, full-duplex gigabit capture, analysis, tren ...more

network monitor and protocol analyzer for Ethernet, Wireless 802.11b & 802.11a, Token Ring and FDDI. Observer provides metrics, capture and trending for both shared and switched network environments. Observer is a cost-effective, software-only, Microsoft Windows-based network monitoring and troubleshooting tool. Observer can monitor single ...more

Real time wafer mapping Real time production control (yield, alarms) Multiple level probing (sampling) Off-line inking Ink-less probing Standard networking Remote monitoring ...more

Real-Time and Post Capture Expert Event Identification, Expert Analysis and Modeling of Network Traffic Data. Expert Observer identifies problems and provides Expert information for faster troubleshooting. Expert Observer: A cost-effective, software-only, Microsoft Windows-based network monitor and LAN/802.11/WAN troubleshooting tool. Expert O ...more

Observer's console can be upgraded to monitor remote LANs, WLANs or WANs by adding either software-based Advanced or RMON Probes, or Hardware-Based Advanced Probes for wire-speed, full-duplex gigabit analysis. Software-based Probes are installed on a remote LAN, WLAN, segment or switch to collect data and report back to the Observer console, a ...more

Network Instruments’ Probe Appliance for 10/100/1000 networks was designed specifically to provide visibility at the edge of the network. By deploying the Probe Appliance for 10/100/1000 networks, you can monitor remote activity in real time from any location, saving valuable time and money that would otherwise be spent flying out an administrator ...more

Tone tracing probes designed specifically to meet the needs of organizations operating large copper networks and in particular those who are committed to improving service delivery and reducing whole life costs. ...more

Specifically designed for integration in network analyzers, IPTV probes, residential gateways, IP set top boxes, videoconferencing and test equipment, VQmon/SA-VM efficiently analyzes multiple parallel packet (either RTP or MPEG Transport) video streams producing Telchemy Video Quality Metrics (TVQM).  ...more

The PA Probe is a small but high-tech extension for the ProfiTrace analyzer that makes it possible to do measurements directly on the PA bus. With the PA Probe, you can use ProfiTrace on DP as well as PA networks and finally cover all installations with 1 tool.  ...more

The STX 1553 Probe, powered by ITCN?s Real-Time Trace technology, is designed for use in the SystemTrace STX platform for network-centric instrumentation. The 1553 Probe is capable of monitoring and recording activity on up to four dual redundant MIL-STD-1553 busses ...more

 Network Tone Generator with full RJ45 breakout (apply tone to any pair); Network Tone Probe II. ...more

Fault Isolation Tool Set (FITS) Development System (Part No.: SSID110) -- All the software for developing and supporting fault isolation for production testing. The package includes development and runtime program modules for network-directed guided probe, fault dictionary and graphic browser. Included is an execution resource and driver set f ...more