Showing results: 4741 - 4755 of 8448 items found.
-
HS-SFRT -
HenergySolar
HS-SFRT silicon filament resistivity tester is an advanced silicon cylinder resistivity tester, which can measure silicon filament, silicon phosphorus ingot, silicon boron ingot, seed crystal and so on. As it eliminates Peltier effect, Seebeck effect, minority carrier inject effect and so on, So it improve the accuracy greatly. The testing resistivity ranges from 0.0005Ω·cm to 50000Ω·cm. It is accurate, stable and convenient and a good friend to Siemens polysilicon material producer, SH4 polysilicon material producer, UMG polysilicon material producer and so on.
-
VULCAN Series -
HORIBA, Ltd.
The high-precision chassis dynamometer VULCAN series is suitable for testing Light-Duty-Vehicles (LDV), Medium-Duty-Vehicles (MDV), Heavy-Duty-Vehicles (HDV) as well as 2-3 wheelers and ATVs. Available as either a two-wheel or a four-wheel drive set-up, HORIBA chassis dynamometers are suitable for electrified mobility with an improved energy efficiency of up to 97% efficiency. Equipped with the synchronous motor technology in each individual roller, they also cover technical requirements in high-performance ranges and allow a significantly better torque distribution when it comes to electrified vehicles.
-
SPECTROMAXx -
SPECTRO Analytical Instruments GmbH
The SPECTROMAXx stationary metal analyzer is used mainly for material testing in foundries and for incoming and outgoing inspections in the metal industry around the world. It determines all of the elements used in the metal industry, including metal analysis of carbon, phosphorous, sulfur and nitrogen. The seventh generation of the SPECTROMAXx arc spark OES metal analyzer comes with drastically reduced operating costs, significantly shorter measuring times and less maintenance requirements while still offering exceptional precision and stability. And when it comes to productivity, the new SPECTROMAXx sets the benchmark.
-
TestGenie -
Corelis, Inc.
TestGenie is a low-cost boundary-scan solution for those companies that have a genuine requirement for JTAG testing, but have difficulty absorbing the tool costs or assigning the resources required to implement the test technology into their development or production processes. TestGenie allows customers to use full-featured versions of Corelis ScanExpress products at a fraction of the cost.Once you’ve selected boundary-scan as a practical solution, the second biggest decision is whether you want to do the test development yourself or have a third party do it. The decision should not be considered lightly as there are advantages and disadvantages to each.
-
Production Triangular Voltage Sweep (TVS) Option -
Materials Development Corporation
In traditional TVS measurements, the operator must select the end points of the mobile ion peak todetermine the area to analyze. Though the selection of these points is a simple matter for the operator, the required input precludes using this technique in asemi-autonomous production environment. The goal of TVS Production testing is the rapid determination of mobile charge concentration with little or no operator input. The test methodology must be compatible with production environments where accuracy, easeof use, and minimum operator involvement are of paramount concern. Also, the possibility of automated wafer handling must be considered.
-
Cincinnati Sub-Zero Products
Our complete industrial oven product portfolio consists of heating and drying ovens, curing ovens, tempering ovens, conveyor ovens, tempering ovens, vacuum ovens, sterilizing ovens, explosion resistant ovens, conveyor ovens and IR Infrared ovens provide the technology for your testing and production processes needs. With advanced user and product safety features, our ovens meet many safety and industry requirements including EN 1539, and AMS 2750E or CQI-9. We have both pre-engineered and custom solutions.
-
Model：OLT-20 -
ShinewayTech
OLT-20 Optical Loss Tester integrates laser source module and power meter module in one set, which can perform power testing and link loss testing in optic fiber network conveniently. The typical applications include fiber identification, attenuation and loss measurement, continuity verification and fiber link transmission quality evaluation for installation, routine inspection and daily maintenance of MAN, WAN and CATV systems as well as for lab test and research work.
-
61800 Series -
Chroma ATE Inc.
The increased demand for Distributed Energy Resource (DR) products such as PV Inverter and Wind Energy systems, have increased the demand for regulation test standards to insure proper operation and safety of on-grid products. Manufacturers testing to prove compliance, need test equipment that can simulate and measure and test their products. Chroma’s 61800 family of Regenerative Grid Simulators provide a full 4 quadrant, regenerative, grid simulation for compliance, safety, and product verification testing
-
LD-LOGA-A10 -
Labodam
Oil and Grease analyzerLD-LOGA-A10is a tabletop analyzer with a sample testing range of0.12 mg/L to 840 mg/L. The unit displays and prints the sample spectra, position and wavenumber of the absorption peak. It features self-contained optical and electrical system withhigh degree integration. Testing data and spectrograms can be saved to hard disk forchecking and printing anytime Sensor signal processing uses lock-in amplifier circuitimproving the analyzer’s SNR and the minimum detection limit.
-
K-1000 Resistive/Reactive -
Kongter Test & Measurement Co., Limited
Resistive/reactive load banks are great choices for testing turbines, switchgear, rotary UPS, generators and UPS systems. They can also be used for integrated system testing of utility substation protection systems, particularly for more complex relays like distance, directional overcurrent, power directional and others. A resistive/reactive inductive and/or capacitive load is often required to test solar inverters to ensure solar panels can be stopped from producing electricity in the event of a power outage.
-
Yangzhou Power Electric Co., Ltd
The AC test transformer are especially designed for testing high voltage products and components, such as cables, power transformers, gas-insulated switchgears, bushings and arresters. It is also suitable to test insulation materials. They are used to generate testing high voltage and function as part of the complete system. These systems are particularly suited for tests requiring stable voltage even if the load changes under voltage (corona, wet & pollution tests) or when the load is inductive (inductive voltage transformers).
-
M2 Optics, Inc.
The handheld Fiber Optic Power Meter is a user-friendly tool for engineers testing and maintaining fiber optic systems & networks. Both compact and rugged, these devices can be used for absolute optical power measurements, as well as relative loss measurements. In addition, high accuracy and a user self-calibration function result in an excellent overall value.Ideal for single mode and multimode testing (800-1700nm), the power meter also includes batteries, protective rubber boot, and a soft carrying case.
-
IT-25B -
Clinton Instrument Company
While most military standards now favor high frequency spark testing over impulse spark testing, the IT-25B Impulse Spark Tester is available for use in some aeronautic applications that still specify the impulse method. The IT-25B meets the test requirements of military specifications MIL-C-13777E, MIL-W-16878, and NEMA standards for hook-up wire used in high temperature wire applications. This method is favored as an alternate to a wet dielectric test.
-
GATS-3200 -
W.M. Hague Company
* Test individual packages or * Test Multi-image panels with Step&Repeat Function * single flying probe top using very high speed voice coil motor (VCM) technology * 50 - 100 tests per second ... high throughput * Dual Flying Probe Top for testing bump-to-bump nets * flying probe head allows testing of all nets including each power and ground point * 4-wire test capability
-
ADSE 650 -
ATEQ Aviation
The ADSE 650 caters fully for all aircraft types and the different electrical power supplies.It can be used for testing high performance civil and military aircraft, fix and rotary wings. This Pitot Static Tester is designed primarily for flightline use to cover the testing of all barometric and manometric pressure instrument systems.The large touch screen display, with on-screen help ,enables all checks to be carried out easily on the flight deck or in the cockpit, by a single operator.
