Showing results: 2701 - 2715 of 5211 items found.
-
BK2116 -
BaKo Co., Ltd
As the technology for BLDC motors advances, more advanced testing is also needed. The BK2116 DC Vibration Motor Tester was designed when of several of our clients needed to test the new generation of 3 port DC vibration motors. Using the BK2116, you can test the electrical specifications (RPM, current, drop pulse, and start up voltage) and also vibration level, and noise of motors with either 2 or 3 ports. The BK2116 can concurrently test 2 DUT's and BaKo's Test Shop software makes it very easy to set up and test. And because you use it with a PC or notebook, you can see graphs of the data as you test, and also save it to analyze later, or to analyze the data you gather over time.
-
Banair
Switches can use all these operations. Membrane switches, keyboards and keypads will all require a push with a known force. On/Off switches will combine a push and a pull or possibly push on, push off. A rocker switch and toggle switches will require a push in two different places. Rotary switches (and volume controls, potentiometers) need to be rotated clockwise and counter clockwise The standard life cycle and fatigue tester the B886 Simon System has been designed for life cycle and fatigue testing of switches, membrane switches, keyboards and keypads. It contains all the components needed to life and fatigue test a products that need to be pushed. We can also supply different actuators for a push, pull, rocker, toggle, volume control or rotary switch.
-
16814 -
Ultra-Tech Enterprises, Inc.,
The MU Locomotive Trainline/Cable Test System (MU Test System) can perform shorts testing, continuity testing, and ground-leakage testing on each of the 27 pin Multi-Unit Trainlines normally found on Freight Locomotives. The MU Test System is comprised of two identical tester units. Each unit is installed in a rugged, water resistant Pelican case. Each unit contains an MU cable receptacle that mates with a 27 pin MU jumper cable. A snap-on vinyl pouch on the outside cover of each unit provides storage for the battery charger/power adapter and the chassis test lead. The enclosure cover hinges separate from the test unit as the cover is opened; this removes the cover completely to allow free access to the MU cable receptacle and the control panel.
-
SW-6 -
Lisun Electronics Inc.
SW-6 Power cord bending tester is fully designed according to the IEC standard, and can also be costumer-sized depends on the samples’ type and the costumer’s requirement. Specifications: • Power supply：AC220V 50/60HZ 12KVA • Control mode: PLC with touch screen and Servo motor. • Test Speed: 10~60times/min (Adjustable) • Test Degree: 0~540° (Adjustable) • Counter: 0~999999 (Can be pre-set) • Weight: 5N,10N,20N. 2Sets. (6Position type will have 6 Sets) • Position: 2/6 • Load Current: 0~20A (Adjustable) • Angle plate: Can check the test situation • Sample fixture: Can be costumer-sized. • Can do power line bending test (The User need prepare sample and power supply ), Can record the number of the sample’s work with load.
-
2675Y -
Shenzhen Chuangxin Instruments Co., Ltd.
The 2675Y Medical Leakage Current Tester Series Is The Test Equipment Used For Measuring Continuous Leakage Current And Patient Auxiliary Current Of Medical Electrical Equipment.It Designs And Products According To The GB9706.1_2020 (IEC60601-1:2012) .And The Test Circuit (MD)Input Impedance To Simulate The Body Impedance,It Accord With The Requirements Of GB9706.1-2020 (IEC60601-1:2012),The Test Current Can Run Up To 5A,And Provide Users With An Isolation Power Supply Which Adjustable Output Voltage For 0~250V Continuously Of The Basic Capacity Configuration For The 500VA And Provide Another 110% Voltage Source Of The Maximum Rated Voltage.It Can Satisfy The I,II, Various Types Of Equipment Test The Earth Leakage Current,Shell Leakage Current,Patient Leakage Current,Patient Auxiliary Leakage Current Under Normal Condition And The Single Fault.
-
Hydraulic Technology, Inc.
Start with the basic Model 9901 hydrostatic tester as shown to the left with the following standard equipment:- Hydrostatic test pump, air operated.- 1% ANSI B40.1 Grade 1A stainless steel high pressure gauge.- ANSI B40.1 Grade B air pressure gauge.- Micro adjust precision regulator.- High pressure isolation shutoff valve.- Automatic lubricator.- Stainless steel high pressure manifold.- 1/4" NPT accessory port.- Bleed valve.- Air shutoff valve.- Factory set air pressure relief valve.- 7/16-20 straight thread O-ring boss outlet port (MS33649-04) with -4 male adapter fitting.- 3/4" swivel female hose inlet with strainer.- Stainless steel base plate with rubber feet.
-
Qualitest International Inc.
Qualitest provides quality control departments and research laboratories with an extensive range of top quality Durometer and hardness Tester for accurate hardness determination on all natural and synthetic rubber products and soft elastic materials, plastics, acrylic glass, acetates, casting resin, polyester, thermoplastics, PVC, neoprenes, hardboards, wood, leather, fruits and much more. Our products provide the highest precision (normally 0.5% or better), quality and craftsmanship, durability, “yet require” almost no calibration in many years after the purchase. Our designs are engineered so that the Durometer stays precisely within the standard requirements. Qualitest Durometers are referred to as the “Swiss watches” among other products on the market. Investing in our line of Durometer is a guarantee of accuracy and assurance for many years of operation.
-
TP800110 -
Total Phase Inc.
The Total Phase Advanced Cable Tester v2 is the quickest and most convenient way to comprehensively test USB, Lightning, and video cables. It provides:*Short testing - Dynamic visualization of test results*Open testing - Dynamic visualization of test results*Continuity testing - Dynamic visualization of test results*DC resistance measurement for most wires, with milliohm precision on ground and power wires, ohm resolution on most other wires, continuity check only on high-speed data lines*Signal integrity testing of data lines to 12.8 Gbps per channel*E-Marker verification*Lightning plug bring up/function (Apple Lightning Cables)**Over-voltage protection (Apple Lightning Cables)**Voltage recovery testing (Apple Lightning Cables)**Quiescent current consumption (Apple Lightning Cables)*
-
SCR ELEKTRONIKS
Dry Arc Resistance Tester is designed to conduct high voltage,low current Arc Resistance test on solid electrical insulation material as per:ASTM standard D495-99 (2004) and UL 746A. Why Arc Resistance Test? Many Cases of insulator failure are due to deterioration of its surface because of sustained electrical discharge or Arc. This test method is intended to test the resistance of insulating material when a high -Voltage low -current Arc close to the surface of insulation, intending to form a conducting path therein or in causing the material to become conducting due to decomposition and erosion.AdvantagesThis Test ensures that your products meet high standards of quality & safety. This product is meant for all Switchgears/ insulator/ Polymer/ electro plastic manufacturers and manufacturers who use insulators in their products e.g. Wiring Accessories, Appliances, HT/LT line insulators etc.
-
1824 LP -
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Measures Earth Resistance without the need for poles in the ground or external measuring wires.● Earth measurement uses the real earth current path and the current generated by the electric network, without the need for any disconnection.● The Earth Resistance displayed is exactly the earth resistance that the earth current will need to go through if an earth fault occurs. (you do not need to add all the bonding points and connection paths)● Displays voltage supply at the transformer(Line to Neutral), without loading the transformer.● Single one smart push button operation; ON, Scroll through results and menus.● Checks wiring integrity (LEDs).● Auto-off / Auto-ranging (software range).● Color-coded test leads.● Combined prospective short circuit current, loop, and earth tester.● Loop test for L-E and PSC between L-N.● Voltage test L-N.● Display can be customized for large orders.
-
WA 180 -
Wuhan Sangao Electrical Test Installations Limit Co.
WA180 Type Large earth resistance tester,To test substation earthing network(4Ω), Hydroelectric and Thermoelectric Power Plant,microwave(10Ω),lighting rod(10Ω)etc.Using new type variable frequency AC power supply, And adopts microcomputer control and signal processing measures, Solved the problem of interference of the testing process, To simplify the test procedure, To improve the precision and accuracy of the test results, reducing test personnel's the labor intensity and the cost of testing.The instrument can be used to test all kinds of power frequency earth resistance,contact voltage,step voltage etc frequency power parameters and soil resistivity. The instrument adopts the different frequency Anti-interference resistance technology, under strong interference environment accurately measured the frequency under 50Hz data.The maximum test current is 5A,it will not cause the earth device potential too high,and it also has strong anti interference ability, so it can be measured in the case of non power.
-
Educated Design & Development, Inc.
Fast - All operator controls are located on the front panel to expedite testing. The entire test can be performed in a matter of seconds! Pays for itself in time and stress savings. Versatile - Measures Leakage Current in accordance with UL, CSA, EN, and IEC/ International Standards. Includes ability to perform open neutral, open ground, and line polarity forward/reverse test conditions. Adaptable - Universal rear panel receptacle allows for testing products with any plug configuration. Accurate - True RMS meter accurately measures both sinusoidal and non-sinusoidal waveshapes. This is important when testing products using a switch mode power supply which can generate non-sinusoidal leakage currents. Calibrated, traceable to NIST. Flexible - A front panel switch permits testing either through the power cord of the product under test, from surface/ patient connection-to-ground, or from surface/ patient connection-to-surface/ patient connection. Portable - Lightweight, with integral handle. Other Features - Product Ground Switching (grounding conductor maintained to device under test when not measuring leakage). Automatic front receptacle disconnect when configured in the 240V test mode (prevents inadvertent connection of 120V when configured for 240V operation). Proven - These are the only leakage current testers designed and supported by Product Safety experts. That is part of the reason why they have become the standard in the industry. Full technical support by experienced safety engineers.
-
Chinup Technology Co., Ltd.
The cell I/V sorter is a machine for PV panel manufacturingfactory to inspect and auto sort the cells. The sorting resultcan be used to improve power lose(%) of PV panelmanufacture, or the quality evidence to negotiate with cellsuppliers.
-
24550 -
Lisle Corp.
Safe for automotive computers. Won’t damage sensitive electronic components. Draws less than 21 mA. at 12 volts DC. Operating range 3-28 volts. The red light indicates positive polarity, green indicates negative polarity.
-
SKZ146D -
SKZ Industrial Co., Ltd
To determine charpy impact properties of plastics, rigid plastic sheet, pipe, digital type.With stable and reliable performance, high precision, easy to use, can be directly calculated impact energy, save 60 historical data, six kinds of units transform the two-screen display can show the practical point of view and angle peak or energy.
