Filter Results By:

Products

Applications

Manufacturers

Test

to find acceptable or limits of.

See Also: Testers, Testing, Specimen


Showing results: 1111 - 1125 of 14526 items found.

  • HSI Test Fixture

    TA-552 - Tech-Aid Products

    This test fixture provides the necessary panel controls, switching and cable pin-outs required to test the KPI-552/KPI-553/A series of HSI's as described in their respective maintenance manuals. This fixture will serve as the "Instrument Bench Tester" and does have the required differential resolvers and relay switching. Panel jacks are provided for the Heading, Course, RMI and ADF synchro sources that are external to this fixture. The use of external synchro sources serves to minimize the cost of this panel. Additional items incorporated on the panel are test jacks to monitor the meter drive voltage and current as well as a momentary switch to open the meter drive and this serves to verify sticky meter stops. The fixtures rear panel provides for all power inputs as well as an I/O connector if the shop desires to interface an external synchro panel.

  • Wire Test Unit

    McGan Technology

    The Wire Testing Unit (WTU) is used in conjunction with the MMPD-8K kit or the MM5KV Kit purchased with the optional HV Red Wire and is used to easily test the continuity of electrosurgical cables used to connect the electrosurgical generator either to the active handpiece (e.g. laparoscopic instruments or forceps) or to the return electrode which completes the circuit between the generator and the patient. If the conductor is broken without damage to the cable’s jacket it can remain unseen and could be put into use for the electrosurgical operation causing the system to not properly function. By using the WTU you can test to ensure that the cables have continuity prior to actual usage in the operating room. This does not preclude the other tests that should be performed on these cables such as visually examining the cable for jacket damage including cracks, pinholes and abrasions and manually flexing the cable.

  • OTP-Based Test System

    LXinstruments GmbH

    Power electronics assemblies often cannot be tested using conventional technology for their electrical performance. Due to the adaptability of the instrumentation, the OTP concept offers an ideal platform even beyond the space requirements of several control cabinets. In order to achieve high test flexibility with different assemblies, the system was equipped with three-phase AC sources and AC loads as well as a precise three-phase power meter. DC sources and loads with different current and voltage ranges cover the test of frequent DUT operating parameters. Time-dependent voltage or current signals can be stimulated by an arbitrary generator with power amplifier. General measurements such as current, voltage, frequency, resistance can be carried out flexibly at various test points using the matrix concept. An oscilloscope with RF multiplexer is available for high-frequency measurements such as residual ripple, switching processes, etc.

  • Loss Test Set

    HPT-5100 - Scitec Instruments Ltd

    The HPT-5100 represents a significant improvement in technology at a competitive price. This high performance loss test set has advanced features commonly found in instruments costing far more.

  • Tester & Test Sets

    Testek Solutions

    Testers and Test Sets for different functions are available for use at the depot (inside the building), I & O level and field (outside building) use. A brief overview is indicated below.

  • APU TEST SET

    H296B - Howell Instruments, Inc.

    The H296B Auxiliary Power Unit (APU) Test Set simulates the APU for static testing of the start sequence control unit and monitors APU temperature and RPM during operation.

  • Hammer Test System

    Empirix

    The Empirix Hammer Test System is the leading automated solution for real-world contact center testing to optimize Quality of Experience. It is a complete testing solution in a single, easy-to-use package.

  • Test Automation Systems

    iTest - A&D Technology, Inc.

    Our iTest family of test automation systems provide a full range of capabilities, allowing you to purchase just the right solution for your application without having to overbuy.

  • Ultra-sonic Test System

    V-Meter - James Instruments Inc.

    The V-Meter is an advanced ultrasonic, pulse-velocity test system widely used for quality control and evaluation of concrete structures. It can identify non-homogeneous conditions such as voids, cracks, honeycombs and frozen concrete.

  • Ozone Test Chambers

    Labodam

    Labodam Ozone Test Chambers are designed to detect the concentration of ozone while requiring low maintenance, having well-built corrosion resistant bodies, and while utilizing noiseless generators.

  • Discrete Devices Test

    FTI 1000 - Focused Test, Inc.

    The FTI 1000 tester consists of independent test channels that allow all DC and AC MOSFET parameters to be tested either separately, or in one handler insertion or prober touch-down.

  • Test Engineering & Manufacturing

    AmFax Ltd

    Whether you require just a test fixture, a complete automated test solution or a build to print service, we will work with you to ensure you get the best return on investment possible. We have highlighted our three key services for you below. Our hardware engineers are regularly trained and certified to ensure best practice. All of our software engineers have certified developer accreditation which means the code we produce is concise, easy to maintain and scalable.

  • Component Test Scanner

    Model 13001 - Chroma ATE Inc.

    Support component test scanningSupport 8 slots for plug-in (removable), up to 320 channels for one unitOption A130007 40 channels scan module, input up to 500VDC for IR test without switchingMax. 8 salve units for multiple scanner (master/slave interface)Support Chroma LCR meterSupport Chroma 3302/3252/11025 turn ration functionSupport 11200 CLC/IR meter for IR testStandard RS-232, GPIB and USB interface13001 can be installed in Chroma Component ATE model 8800Support ICT applications

  • Disintegration Test Apparatus

    Kaypee Udyog

    We are offering a qualitative range of Disintegration Test Apparatus. The offered range works on up and down movement of tablet in medium of water kept at 37^C. this apparatus is designed for accurate estimation of disintegration time of tablets as per IP/USP standards. We assure our clients that our Disintegration Test Apparatus is quality tested on predefined parameters, in order to meet international standards. Apart from this our prestigious clients can avail this apparatus, as per their needs, at highly competitive price.

  • Sand & Dust Test

    Aero Nav Laboratories, Inc.

    This test method is divided into two procedures. The small particle procedure, using fine dust is performed to ascertain the ability of equipment to resist the effects of fine particles which may penetrate into cracks, crevices, bearings, and joints. The blowing sand test, using coarse particles, is performed to determine whether equipment can be stored and operated under blowing sand conditions without experiencing degradation of its performance, effectiveness, reliability, and maintainability due to the abrasion or clogging effect of large, sharp-edged particles.

Get Help