Showing results: 5431 - 5445 of 6622 items found.
-
Acroname, Inc
As part of Acroname's MTM series, the MTM-IO-Serial module is a key component to manufacturing test systems for electronic devices using a standard USB 2.0 interface, serial UARTs and one or more interface voltages. The MTM-IO-Serial module features a software controlled USB hub (USB 2.0 high-speed) with four controllable channels. Each channel has switched data and 500mA current-limited power lines.
-
MCL-500IRV -
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Safety by non-contact sensor, not touching live part directly (prevention of electric shock, short-circuit, etc.).・Easy to carry and operate, clamp CT + display part integrated type.・Measurable line current + leakage current + resistive leakage current by one unit.・Available direct voltage input at live part as ordinary.・True RMS measurement (I, Io, V).・With filter switch to cut high frequencies.
-
NI
PXI Counter/Timer Modules perform encoder position measurement, event counting, period measurement, pulse-width measurement, pulse generation, pulse-train generation, and frequency measurement. PXI Counter/Timer Modules feature up to eight 32-bit counter/timers and TTL/CMOS-compatible digital I/O. You can also choose options that support filtering, high-speed simultaneous DMA transfers, industrial voltage ranges with isolation, and onboard high-precision oscillators.
-
NI
PXI Digital Multimeters, or DMMs, feature AC/DC voltage, AC/DC current, 2- or 4-wire resistance, and frequency/period measurements, as well as diode tests. You can also choose a PXI DMM with an isolated, high-voltage digitizer that can acquire waveforms at sample rates up to 1.8 MS/s at full input range, up to 3 A or 1,000 V. Additionally, you can choose a PXI DMM that can perform basic inductance and capacitance measurements.
-
40-131-101 -
Pickering Interfaces Ltd.
Low cost, general purpose electromechanical relay cards suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include switching of medium power AC and DC loads or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 50 or 78 pin D-Type connector plug.
-
Fluke Biomedical
Electrosurgery Analyzer is the ESU tester you can depend on for complete preventive maintenance and electrosurgical device safety to completely test these critical functions:* Measures current, voltage and power output.* Tests RF leakage from output to ensure no hazardous currents are present.* Performs Return Electrode Monitoring (REM) tests.* Measures crest factor.* Performs automatic power distribution curve at a wide range of test loads.
-
DUCA-LCD -
Ducati energia S. p. A.
Energy Analyser for DIN-rail mounting (4 modules), for Single-Phase/Three-Phase systems with Graphic LCD screen, Co-generation Energy measurement and "Wide Range" Power Supply (24 - 240 Vac/dc); voltage and current waveforms and harmonics measurement and visualization; 2 digital output for pulses or alarms; 2 digital pulse input. Optional RS485 serial line interface (Modbus or ASCII_DUCBUS), Ethernet Interface (Webserver / Modbus-TCP).
-
Chroma ATE Inc.
Regenerative battery energy dischargeEnergy savingEnvironment protectionLow heat generateChannels paralleled for higher currentsCharge / discharge mode (CC, CV, CP) Constant current Constant voltage Constant powerDriving cycle simulationHigh precision measurement accuracyFast current conversionSmooth current without over shootTesting data analysis functionData recovery protection (after power failure)Independent protection of multi-channelBMS data recordingThermal chamber control integration
-
SD037 -
Synectic Electronics
Synectics’s SD037 dynamically monitors mains frequency. The filter enables high speed, high accuracy, frequency monitoring even with high levels of harmonic noise. The SD037 is highly prized in demand side energy management and the associated battery storage technologies. The unit monitors the frequency of a mains voltage signal and reports the value, on demand, via an RS232, RS485 using either simple ASCII commands or Modbus protocol.
-
cPCIS-2633 Series -
ADLINK Technology Inc.
*3U CompactPCI® backplane with 12 peripheral cand slots and one system slot*2 + 1 hot swappable 500 W + 250 W CompactPCI® Power supply (supports three 250 W PSUs)*Temperature, voltage, and fan monitoring LEDs*Supports current sharing on +5V, +3.3V, and +12V*PICMG® 2.11 47-pin power interfaceHot-swappable cooling fans & filter
-
Kikusui Electronics Corp.
The KES7000 System is a conductive immunity test system that is fully compliant with ISO7637-2 and ISO7637-3, international standards for EMC testing required for automotive electronic components. This system consists of the KES7700 Series Transient Surge Tester, KES7400A Series Voltage variation simulator and KES7100 application software dedicated to the KES7000 system. This product configuration supports JASO standards and the special test requirements of car manufacturers with options or custom orders.
-
Hangzhou Xun Anda Electrical Co., Ltd.
1. Quickly test the battery's main specifications: IR, CCA, Voltgage, so that you can judge its life status easily.2. The tool is suitable for 12V single battery or 12V Battery charging system.3. No need to charge of voltage when start the vehicle.4. Adopt conductance method to test: simple of the vehicle5. Printer inside, can print out testing results.7. LCD Screen
-
PQA820 -
HT Italia Srl
PQA820 respectively record 383 and 44 quantities which can be recalled and dragged onto the screen to be compared between each other; for example, if you are displaying the trend of voltages and you want to check for the possible presence of harmonic distortion, it will be sufficient to scroll through the list of recorded measures and drag the one relevant to harmonics to the screen. The same can be done for all other quantities: power, cosphi, current, energy, etc.
-
Beijing KeHuan Century EMC Technology Co,.LTD
KH8158 is a device for measuring the common mode interference voltage of unshielded twisted pair cables. Cable testing according to CISPR 16-1-2. The equipment under test (EuT) and auxiliary equipment (AE) are directly connected to the corresponding ports. The port adopts RJ-45 socket (the distribution conforms to T568A/B.) This equipment is divided into three specifications: CAT3, CAT5, and CAT6, and the corresponding equipment is selected according to the cable model.
-
LXinstruments GmbH
HV test enclosure for testing medical products (patient monitors). Insulated test booth with large space for DUT.3 different test nests for adapting different devices.Displays from patient monitors are checked. For this, insulation tests and leakage current measurements must be carried out. Ensuring the standard-compliant test. For the safety of the operating personnel, the test cell is electrically locked while the high voltage measurement is active.