Showing results: 5206 - 5220 of 6611 items found.
-
CTTS Series -
Shanghai Jiuzhi Electric Co., Ltd.
CTT series cable test terminations are used to test Plastic insulated high-voltage cables. The specific advantages of this series versus conventional terminations are fast and convenient assembly. The terminations can be used for partial discharge (PD) measurements, impulse voltage testing, loss factor (tan delta) measurements and, if the cable ends are carefully prepared, for breakdown testing (step test).
-
cPCI-3534/3538-S -
ADLINK Technology Inc.
*32-bit CompactPCI, PICMG 2.0 Rev 2.1*Plug-and-play, IRQ & I/O address automatically assigned by PCI BIOS*4/8 asynchronized communications ports with intelligent buffer*Three RS-232 ports and one isolated RS-422/RS-485 port with 2500 VRMS isolation voltage for cPCI-3534, and eight RS-232 ports for cPCI-3538*Surge protector in TXD/RXD signal line
-
Extech MN36 -
Extech Instruments Corporation
The Extech MN36 digital multimeter is compact but still packed with features. Capable of measuring AC and DC voltage up to 600 volts, the MN36 is autoranging, which means it automatically displays readings with the proper decimal place location and maximum resolution. Comes with protective rubber holster, 2xAAA batteries, bead wire Type K temp. probe and test leads.
-
Extech MG320 -
Extech Instruments Corporation
20GΩ/1000V Insulation Tester with a True RMS MultiMeter. Combines a portable 20GΩ/1000V Insulation Tester with a True RMS MultiMeter. Insulation tester includes PI/DAR modes, programmable timer, and a comparator for custom test configurations and quick results. Multimeter functions include AC/DC Voltage, Resistance, and Continuity Test. Manually store/recall up to 99 readings.
-
SECULIFE HIT MD -
GMC-I Messtechnik GmbH
TRMS multimeter that has been designed especially for all hygienically sensitive areas. 23 multimeter functions. Voltage measurement.Auto-ranging current measurement from 100A (resolution: 10nA) to 10A (16A). Capacitance and resistance measurement, diode and continuity testing. Measuring categories: 600V CAT III and 300V CAT IV. Hygiene certificate from University of Marburg
-
EQSFP28 -
Optellent, Inc.
The OPTELLENT EQSFP28 is a cost-effective and convenient test board for testing QSFP28 optical transceivers in R&D and manufacturing environments. The EQSFP28 is equipped with high quality RF connectors for data signals and test points for low frequency control and status signals. The EQSFP28 is equipped with power supplies to enable voltage margining. Key status signals are displayed using LED indicators.
-
ViTec Co. Ltd
The acceptance test station consists of a personal computer - the workstation of the operator of the testing station, contact mechanisms, as well as current and voltage sensors. The station allows to test up to 10 electric motors of various types simultaneously. The operator of the testing station indicates the test sites at which the engine tests will be conducted, their type (from the database), serial numbers and a set of tests.
-
EQSFP10 -
Optellent, Inc.
The OPTELLENT EQSFP10 is a cost-effective and convenient test board for testing QSFP/QSFP+ optical transceivers in R&D and manufacturing environments. The EQSFP10 is equipped with high quality RF connectors for data signals and test points for low frequency control and status signals. The EQSFP10 is equipped with power supplies to enable voltage margining. Key status signals are displayed using LED indicators.
-
FF310 -
General Technologies Corp.
42 V Ready: for use in the new generation of vehicles with mixed or single 42 Volt systems. Operates on DC voltages from 6 to 42 volts. Internally protected against power surges and overloads. 8" flexible probe allows reaching wires in congested places. Transmitter and Receiver LEDs show open or short circuit conditions.
-
TestStation LHS -
Teradyne, Inc.
The TestStation LHS in-circuit test system is a lower-cost, small footprint, feature scalable version of Teradyne’s popular, award winning TestStation product family. Compatible with existing TestStation LH fixtures.TestStation LH features the voltage accuracy and backdrive current measurement embedded in Teradyne’s SafeTest protection technology for accurate, reliable and safe powered-up testing of new low-voltage software.
-
Fourier Systems
The MicroLog product line includes a range of low-cost, portable data loggers for supply chain monitoring, featuring internal temperature and humidity sensors with one external input for connection to temperature, current and voltage sensors. With over a decade of customer satisfaction, the MicroLog continues to offer application reliability for a variety of mission critical industries such as cold chain, healthcare, pharmaceuticals, and storage.
-
TOB-BST8-5V1mA -
Xiamen Tob New Energy Technology Co., Ltd
8 Channel Battery Analyzer (0.002-1mA, up to 5V) with Laptop & Software for R&D Battery Materials. TOB-5V1mA Button Battery Tester is an eight-channel battery analyzer to analyze small coin cells with a range current 0-50mah, voltage 0-5v. Each channel of the analyzer has independent constant-current and constant-voltage source, which can be programmed and controlled by computer software.
-
RT110 -
Klein Tools, Inc.
Light sequence indicates correct/incorrect wiring.Conforms to UL Std 1436, Certified to CSA Std C22.2 #160.Operating temp: 32°F to 140°F (0°C to 40°C).Built to withstand a 6.6 ft. (2m) drop.Nominal Voltage: 110/125V AC at 50/60Hz in 3-wire outlet.Designed to detect the most common wiring problems in standard receptacles.
-
Fluke T6-1000 -
Iconic Engineering Limited
We know operating in electrical boxes packed with wires may be difficult once you’re attempting to seek out a secure gold contact purpose. Now, with Fluke’s T6-600 or T6-1000 with integrated FieldSense technology, you'll be able to quickly and simply take measurements by slippery the open deliver a conductor to visualize the voltage level without the need for test leads.
-
HPRS-HIPOT-LOAD -
IET Labs
The IET HPRS-Hipot-Load is an excellent replacement for the Fluke 5320A-Load Hipot current calibration load resistors. The IET high power resistive load can be used with the Fluke 5320A Multifunction Electrical Tester Calibrator or standalone. It provides a high power and high voltage load to various hipot tester to create the leakage current needed to calibrate various manufactures hipot testers.