Showing results: 1606 - 1620 of 6622 items found.
-
Harmonic Distortion Analysis -
ZETLAB Company
The software is used for automatic measurement of the harmonic distortion factor and voltage r.m.s. of signals coming to the input channels of FFT spectrum analyzers. Adjustment to the frequency of the main component is performed automatically. The program is based on the measurement of the voltage r.m.s. of higher components by an external or internal reference signal.
-
Bestone Industrial Ltd.
It can measure trip-out current, trip-out time, on-line voltage, loop resistance and frequency etc. It’s ideal tool for electrical inspection and repair.Comply with IEC/EN 61010-1 1000V CAT III, 600V CAT IV safety standards.Max common mode voltage: 600V AC RMS.
-
Tabor Electronics Ltd.
Power amplifiers are a must in applications requiring both complex signals as well as high voltage throughput. However, this is uncommon in high performance instrumentation, therefore an external amplification device must be used. In these cases, a high voltage amplifier is used to increase the size of a signal by some factor.
-
N2790A -
Keysight Technologies
Use the N2790A 100-MHz high-voltage differential probe to make safe and accurate floating measurements with an oscilloscope. The N2790A probe allows conventional earth-grounded Keysight oscilloscopes to be used for floating signal measurements of up to 1,400 V of differential voltage and 1,000 V of common mode voltage.
-
N2791A -
Keysight Technologies
Use the N2791A 25-MHz low-cost high-voltage differential probe to make safe and accurate floating measurements with an oscilloscope. The N2791A differential probe allows conventional earth-grounded Keysight oscilloscopes to be used for floating signal measurements of up to 700 V of differential voltage and common mode voltage.
-
PD-20S -
Standard Electric Works Co., Ltd
● Measures both AC and DC voltages with oscilloscopes.● Are typically used to measure high voltages in TV sets, power supplies and instruments in laboratories.● Lightweight and rugged.● 2 available contact tips: round needle tip for normal use and a special flat spring-type for CRT anode.
-
J2101A -
PICOTEST Corp.
The injection transformer is presently the prevalent method for connecting the network analyzer to the circuit being tested, and is primarily used for control loop stability measurements. The goal of the transformer is to inject a signal into the control loop being measured, without impacting the performance of the loop. In order to accomplish this to a reasonable degree, The transformer is isolated and therefore is capable of floating on a high voltage, such as a Power Factor Corrector (PFC), which is often close to 400VDC. Measuring voltages that exceed the voltage rating of the FRA inputs require attenuation probes.
-
J2100A -
PICOTEST Corp.
The injection transformer is presently the prevalent method for connecting the network analyzer to the circuit being tested, and is primarily used for control loop stability measurements. The goal of the transformer is to inject a signal into the control loop being measured, without impacting the performance of the loop. In order to accomplish this to a reasonable degree, The transformer is isolated and therefore is capable of floating on a high voltage, such as a Power Factor Corrector (PFC), which is often close to 400VDC. Measuring voltages that exceed the voltage rating of the FRA inputs require attenuation probes.
-
Renesas Electronics Corp.
Renesas is a leading low-dropout regulator (LDO) supplier in low power handheld applications with world-class differentiated single and dual LDOs which have ultra-high PSRR up to 3MHz, low input voltage range, tiny packages, and ultra-low noise and quiescent current. Renesas' high current LDOs support up to 3A and have industry-leading fast load transient response, tightest voltage output accuracy at full load and over the full junction temperature, and lowest dropout voltage in its class.
-
HK Film Capacitor Ltd
Single phase and Three phase availableSuitable for AC and DC voltage applicationResistance and rate power of Resistor : 1 - 50W ( can be customized to 100W or above )Voltage: 63Vac, 125Vac, 280Vac, 480Vac, 500Vac, 600VacOperating temperature : -25~+85C / -40~+105CTesting Voltage : : 1.5 x Un 10sec ( can be customized )Varistor and Diode options available. Different applications can have very different electrical and mechanical profile requirements.Please feel free to send your application details for a suggestion and quotation.
-
Techimp HQ S.r.L
PPS2 provides power supply to the PD detectors installed on HV cable when low voltage AC power is not available. The PPS2 takes the required power directly from the High Voltage power line under monitoring by means of units clamped on the HV power cable(s).PPS2 is designed to withstand High Voltage line failure events such as temporary overload and short circuit conditions. An internal detection and self limiting circuitry guarantees that PPS2 and the connected equipment survives in case of such events.
-
Acopian Technical Company
*Universal input.*Power Factor Correction.*Output Inhibit*Constant voltage and constant current modes.*Voltage and current monitor terminals.*Voltage and current programming capabilities.*Short circuit and overload protection.*Thermal protection.*Low Profile.*No minimum load required.*Adjustable down to 0 volts (‘Wide Adjust’ models).*Internal EMI Filter and RFI Shielding.*Pluggable connectors for input and control wiring.*Remote Sensing.*‘Vout OK’ signal monitor.*‘Soft start’ operation.
-
DF-600 -
Link Instruments
The DF-600 Differential Active Probe is a high input impedance and low input capacitance probe. It also supports extremely high frequency bandwidth, and high voltage input. It is designed using three OP amps, namely two FET buffer OP amps and a low offset OP amp. Therefore, even with long-term operations, the measured voltage will not drift. The voltage offset always approach 0 volts. (USB power supply should be 5V ±2%). The following diagram shows the circuit of DF-600.
-
IT6700 Series -
I-TECH Electronic Co., Ltd
IT6700 series power supplies are the most economical power supplies, they have the widest voltage and current utilization, one power supply can replace multiple power supplies, widely used in various testing occasions. With the capacity of 100W, voltage output of 60V, current output of 5A, they can control the change rates of the voltage and current automatically. The power ratio can be up to 3 times. For instance, One IT6720 can subsitute previous 60V*1.6A/32/*3A/20V*5A 3 kinds of models to save your cost.
-
TOMSAD
PowerLab triple Series power supplies are reliable and accurate laboratory equipment with two outputs with adjustable and stabilized DC voltage and regulated ( limited ) power consumption and additional output has – voltage . Adjustable outputs can work independently , in series (max output voltage 120V DC for model 605- II) or parallel (max current of 10A for models 305- II and 605- II) . Power can be used in the design of electronic products , scientific works , laboratories, production lines and in teaching .