Showing results: 241 - 255 of 326 items found.
-
NanoSight Range -
Malvern Panalytical Ltd
The Malvern Panalytical NanoSight range of instruments utilizes Nanoparticle Tracking Analysis (NTA) to characterize nanoparticles from 10nm -2000nm* in solution. Each particle is individually but simultaneously analyzed by direct observation and measurement of diffusion events. This particle-by-particle methodology produces high resolution results for nanoparticle size distribution and concentration, while visual validation provides users with additional confidence in their data. Both particle size and concentration are measured, while a fluorescence mode provides differentiation of intrinsic or fluorescently labelled nanoparticles.
-
778572-36 -
NI
544-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXI‑2536 is a high-density 8x68 PXI matrix switch module that is ideal for routing low-power DC signals in validation test systems of mass produced devices such as semiconductor chips and printed circuit boards (PCBs). Featuring FET relays, the PXI‑2536 offers unlimited mechanical lifetime and switching speeds up to 50,000 crosspoints/s. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
779647-10 -
NI
3-Channel, 20 V, 1 A PXI Programmable Power Supply—The PXI‑4110 is a programmable DC power supply. It is an excellent general-purpose, single-quadrant power supply for design validation and manufacturing test applications. The PXI‑4110 has two isolated and a single non-isolated supply channel, all capable of generating up to 1 A per channel. You can program the voltage setpoint and current limit as well as the voltage and current readback/measurement functionality. You can also combine channels for higher voltage or current.
-
779647-11 -
NI
3-Channel, 20 V, 1 A PXI Programmable Power Supply—The PXI‑4110 is a programmable DC power supply. It is an excellent general-purpose, single-quadrant power supply for design validation and manufacturing test applications. The PXI‑4110 has two isolated and a single non-isolated supply channel, all capable of generating up to 1 A per channel. You can program the voltage setpoint and current limit as well as the voltage and current readback/measurement functionality. You can also combine channels for higher voltage or current.
-
R&D Altanova
We offer services for modeling and simulation and complement that work with measurement and validation of those models, at your desired frequency and your required fidelity specifications. Our design and programming expertise includes: Teradyne Catalyst through Integra FLEX; Advantest 3340 through T2000; Verigy 82000 through 93000. turn-key solution for ATE interface boards, we understand the limits of the interconnect technology (laminate, conductors and via’s, connectors and sockets) and use that understanding to guide our principles of design.
-
Kiwa Dare
Calibrations of electronic equipment is one of the activities that Kiwa Dare offers to its clients. these calibrations are under accreditation in the field of electrical quantities. Besides calibrations in the field of DC current, DC voltage and low frequency (test and measuring) equipment, Kiwa Dare is specialized in calibrating high frequency measuring equipment and in particular EMC equipment in a frequency range of (DC) 40 GHz. New the site validation calibrations whereby Kiwa Dare can calibrate shielded rooms (Faraday room) and anechoic chambers under accreditation.
-
IPETRONIK GmbH
Our IPEtec test bench engineering business unit plans and provides customized test bench solutions for the development and validation of automotive AC components. We offer a full range of test benches and media-supply modules for the automotive developer’s thermal management needs. Moreover, we support the development of new cooling systems for hybrid power trains, for battery and engine cooling. New hybrid power trains are opening up additional fields of heat-pump technology development aimed at optimizing the energy balance of automotive air conditioning.
-
PCI301 -
Andor Design Corp.
MIL-STD-1553 A, B & McAir MULTI PROTOCOLS Simulator/Analyzer/Tester PCI BUS Interface Card - The PCI301 can be used for Validation Testing, Production Testing, full bus simulation and monitoring, as a general purpose 1553 interface or a stand alone bus Analyzer. For precise message scheduling and measurements, the Major and minor frame times are independent of message sequences or retransmissions on errors and the start of all command messages are independent of message length, response time or length of response. Message timing is calibrated and RT responses have low jitter.
-
PC401 -
Andor Design Corp.
MIL-STD-1553 A, B, & McAir MULTI PROTOCOLS Simulator/Analyzer/Tester type 2 PCMCIA BUS Interface Card - The PC401 can be used for Validation Testing, ProductionTesting, full bus simulation and monitoring, as a generalpurpose 1553 interface or a stand alone bus Analyzer. Forprecise message scheduling and measurements, the Majorand minor frame times are independent of messagesequences or retransmissions on errors and the start of allcommand messages are independent of message length,response time or length of response. Message timing iscalibrated and RT responses have low jitter.
-
MilliBox Original
If you are involved in antenna or system level design using mmWave or THz frequencies, then you understand the importance of dependable testing equipment. It may be that you are designing passive phase array or that you are designing a mmWave radar sensor system, but when it comes to validation of your design, simulation can only bring you so far. Phased array antennas have to be measured over the air (OTA) to ensure the radiation pattern of your design efficiently conducts energy in the right direction which is where the MilliBox comes in.
-
Shimadzu Corp.
Currently, there is a strong demand for the introduction of development, manufacturing and control systems in accordance with GxP at pharmaceutical manufacturing and development sites. And, in pharmaceutical manufacturing, water quality control in line with the GxP guidelines is also required for water used as raw materials and rinsing water. The TOC-V/L Series conforms not only with USP (United States Pharmacopeia) and JP (Japanese Pharmacopeia) but also with other world standards (EPA, ASTM, JIS, ISO, etc.), and demonstrates its outstanding performance in TOC control and cleaning validation of pharmaceutical water.
-
SAM100 -
Rohde & Schwarz GmbH & Co. KG
The R&S®SAM100 system amplifier is an ultra-broadband solid state microwave amplifier with a frequency range from 2 GHz to 20 GHz. With a power of up to 20 W, outstanding linearity and very good noise characteristics, the R&S®SAM100 amplifier is ideal as a compact system amplifier in various measurement setups e.g. design (DVT) and product validation test (PVT) or EMC. In measurement environments with R&S generators, frequency analyzers or network analyzers, they can act as drivers or boosters and amplify the measurement signals
-
NI
PXI Vector Network Analyzers feature two ports, so you can choose between T/R test sets or full S-parameter capabilities. The PXI Vector Network Analyzer supports automatic precision calibration, full vector analysis, and reference plane extensions, so it is an ideal vector network analysis solution for your validation and production operations without the high cost and large footprint associated with a traditional benchtop VNA. These models seamlessly integrate into test systems for highly accurate, fast RF measurements.
-
APXX1553-x -
AIM GmbH
MIL-STD-1553 Test and Simulation Module for PCI with 1, 2 or 4 Dual Redundant channels (APXX1553-1, APXX1553-2, APXX1553-4) plus 8 programmable discrete Input/Output channels. A unique feature of AIM’s APXX1553-x module is the option for the MILScope™ capability. Models APXX1553-1-DS/APXX1553-2-DS integrate an onboard Analogue to Digital Converter (ADC) which samples, measures and stores the MIL-STD-1553 waveform. Automatic waveform validation is performed by the users Application Software or in conjunction with AIM’s PBA.pro Databus Test and Analysis Software and Test Scripts.
-
TPS Associates, Inc.
TPSA has over 20 years of experience in Engineering Design & Software Development including:Hardware & Software DesignOTPS Acquisition SupportSystems Installation & SupportAircraft Modification/CertificationEngineering Studies & AnalysesFunctional & Systems TestingIndependent Verification & Validation (IV & V)Test Program Set EngineeringReliability & Maintainability (R&M)Engineering Drawings & DataConfiguration Data ManagementReverse EngineeringRequirements AnalysisSupport Equipment (SE)Aircraft Launch & Recovery Engineering (ALRE)Engineering Change Proposal (ECP) ReviewTechnology Insertion (TI)PDR, CDR, FAT, Techeval, OSV Support
