Showing results: 31 - 45 of 68 items found.
-
GT-1040A -
Spanawave Corporation
The Spanawave/Giga-tronics GT-1040A Microwave Power Amplifier incorporates broadband MMIC-based architecture. These state-of-the-art amplifiers are based on solid-state parallel MMIC design with exceptionally wide bandwidth and high power. The unique circuit topology is highly reliable, with performance that excels where extremes of bandwidth and power are demanded.
-
EMHP -
TDK-Lambda Corp.
The EMHP series of power supplies is the highest power line of DC regulated high power units available in the range of 20-90 kW. Based on a regulated SCR phase control topology the EMHP series is ideally suited to applications where raw bulk power is required in a robust reliable package.
-
aTCA-80606PD -
ADLINK Technology Inc.
*19” Rackmount, 6U height, 438mm depth*6-slot dual-star topology Fabric Interface*6-slot standard Rear Transition Module*Dual-bussed IPMB*Hot-swappable IPMC controlled fan trays*Two shelf management controller slots*Dual -48 V DC power entry modules
-
aTCA-81514PA -
ADLINK Technology Inc.
*19” Rackmount, 15U height, 470mm depth*14-slot dual-star topology Fabric Interface*14-slot standard Rear Transition Module*Dual-bussed IPMB*Hot-swappable IPMC controlled fan trays*Two shelf management controller slots*Four 115V AC / 230V AC power supply units
-
ADLINK Technology Inc.
The PICMG CPCI-S.0 CompactPCI Serial standard, which evolved from the PICMG 2.0 specification, is the fastest, most versatile, most cost-effective open standard for CompactPCI (CPCI). The Serial standard is mechanically and electronically compatible with 3U and 6U euro-cards, defining an interface for high-speed switched fabrics with a star topology. Point-to-point connectors allow up to eight peripherals on one system slot without switches or bridges. Ethernet data transfer can be configured with full mesh topology, which allows up to 1000Base-T connections to all peripheral slots for redundant, safety-critical systems.
-
HSL-HUB3/Repeater -
ADLINK Technology Inc.
HSL system is a great remote real-time I/O control solution. HSL-HUB3/Repeater comes with HSL technology and provides much flexibility in HSL system topology and extension. Machine makers and FA planners can use this extension module to install subsystem and process remote side (2.4 km) I/O even motion control.
-
Renesas Electronics Corp.
Renesas' power factor correction (PFC) controller family uses boost topology and are suitable for AC/DC power systems, up to 2kW and over the universal line input. These PFC controller IC's operate in continuous conduction mode (CCM), and the small external components result in a low cost design without sacrificing performance.
-
ABex Switching -
Konrad Technologies GmbH
The ABex Switching features a text-based way to connect and disconnect relays on ABex modules. Alias names for channels could be defined in a DUT specific topology file and then be used for text-based switching. These alias names are also shown in the Konrad System Manager allowing easy debugging of test sequences. The ABex Switching functionality could be either used out of NI Teststand with the provided test steps or via API from other programming languages.- Text-based switch routes- XML based topology for Alias mapping- Switch routes with support for Alias names- Seamless integration into Konrad System Manager
-
STMicroelectronics
The ST rectifier diode designs deliver performance for applications with very different VF/Qrr trade-offs depending on targeted functions. The minimal power losses of the ST rectifiers range is totally adapted to mains rectification, bypass, boost, bootstrap, freewheel and HF rectification functions. Inside these generic functions, the topology evolution in e.g. resonance or multilevel is followed constantly by suited designs. Ultrafast rectifiers are belonging to the STPOWER family.
-
34980A -
Acery Technologies
34980A Universal Switch Module 34937A, 34938A can be used to send signals or control other devices in the application. The 34937A is a versatile universal switch with 28 channels capable of switching up to 1A. In addition, there are four can switch up to 5A of the A-channel. The 34938A has 20 5A channels of type A topology. Each type A general-purpose switch can withstand up to 150W of power per channel, suitable for power switching.
-
Analog Devices Inc.
Analog Devices voltage variable attenuators (VVAs) ensure accurate control for a wide range of applications. Our absorptive VVAs are ideal for designs where an analog dc control signal controls RF signals levels over a 30 dB amplitude range, while our monolithic VVAs feature low insertion loss, high IP3, and wide dynamic range, as well as a balanced topology that delivers excellent return loss.
-
LXinstruments GmbH
Functional test system for testing PLC peripheral modules. The DUTs are examined with the help of the system before repair and calibrated and finally tested after repair. With the help of product-specific personality modules, the internal cabling of the system can be adapted to various test object topology without the need for a large number of matrix channels.
-
Kontron
This 5 slot Hartmann VPX 4U desktop system chassis provides a portable packaging solution for high-performance processors on a full mesh backplane topology. The 42HP wide desktop enclosure for vertical mounting of boards is outfitted with a 300W ATX power supply and a 1U fix bottom mounted fan tray.
-
GPON Phantom™ -
TraceSpan Communications Ltd.
GPON Phantom™ is a unique passive tapping device for Lawful Interception (LI) of optical fiber lines using GPON technology and deployed in a Fiber-to-the-x (FTTx) topology. The GPON Phantom records and stores broadband digital information, offering unique advantages for Law Enforcement Authorities (LEAs) looking to capture any data between the central office and the target, without being detected, while providing solid evidence with unique identification of the target.
-
CUT35 -
TDK-Lambda Corp.
The triple output CUT35 and CUT75 power supplies have two independent, isolated, converters, one for the main 5V output, and one for the auxiliary outputs. This topology provides several benefits - no minimum loading, enhanced load & line regulation and the ability to connect the auxiliary outputs in series to generate either a 24V or 30V output. This flexibility makes it suitable for use in a wide range of process control, broadcast, test & measurement, medical and industrial equipment applications.