Showing results: 4141 - 4155 of 5371 items found.
-
ET4000 -
Martindale Electric Co. Ltd
The new ET4000 tester carries out all the tests needed to verify the safety of electrical installations in domestic, commercial and industrial wiring installations in accordance with the latest regulations.
Everything about the new ET Series has been designed to save time and make testing easier.
Fast, reliable high current and non-trip loop testing comes as standard together with a high level of input protection and a CAT IV safety rating .
Supplied with a full range of accessories.
-
ELT-400 -
Narda Safety Test Solutions
*Wide frequency range (1 Hz - 400 kHz)*Standard-compliant measurement*Acceptance measurements compliant with CE standard IEC/EN 62233 and Generic Standard IEC 62311*Limit value traces conforming to ICNIRP 1998, 2010 and EMF Directive 2013/35/EU*Real time measurement with RMS and peak detectors*External FFT signal analysis for determining the frequency components via three channel analog output (one channel for each spatial axis) e.g. with the aid of a digital oscilloscope.
-
TM263N -
T&M Tools Limited Co
◇ Added Network Cable Test ◇ Accurately test whether a single network cable transmits signals normally ◇ Self Calibration ◇ Set the Auto Off ◇ Wavelength Memory function after turn off the tester ◇ High Accuracy, high ,High sensitivity, high linearity ◇ Stable VFL Output ◇ USB Charge port ◇ FC,SC Connector ◇ 18650Li-ion Battery ◇ Lower power consumption design, long standby time ◇ Rubber Out shell, increased the protective properties for field work
-
Labodam
Labodam Octane Number and Cetane Number Testers are portable devices for rapid petroleum products quality monitoring in fields and lab environment conditions. Glass detector has a built in element sensitive to fuel sample temperature detection. The instrument electronic computing module processes detector signals, performs all necessary calculations, and constantly tests the main function modules. It is ideal used in the determination of octane, cetane numbers, our point depressants and break down time in the oil and petroleum industries.
-
PK-170 INNOTESTER PRO -
Pansco, Ltd
INNOTESTER PRO combines the functions of a smart cable tester, network tester, port identifier and organizer with the capability to identify up to 100 cables run at a time, and 8 Test + ID remotes allows one person to test 8 cables run up to 600 meters. Tone mode, transmits 2 powerful tones for tracing inactive and active network cables on a Switch or HUB. More effectively tracing at patch panel, termination blocks or hidden within bundles.
-
WT3-201M -
Mark-10 Corp.
The WT3-201M motorized wire crimp pull tester is designed to measure pull-off forces of up to 200 lbF [1 kN] for wire and tube terminations. The tester conforms to numerous UL, ISO, ASTM, SAE, MIL, and other requirements for destructive testing. Non-destructive testing is also possible, such as pulling to a load or maintaining a load for a specified period of time, as per the requirements of UL 486A/B. Programmable pass/fail limits with red and green indicators and audio alerts help identify non-conforming samples.
-
Explorer® 2 -
Klein Tools, Inc.
Tests coaxial cable and maps up to 4 locations. Tests coaxial cable and maps up to 4 locations. Simple push button operation • Easy-to-read LED panel indicates PASS, OPEN or SHORT conditions, simplifying cable identification • Color-coded push-on remotes allow for up to four cables to be tested and mapped at the same time• 4 color-coded test remotes and included F-adapter conveniently snap into the remote holder for storage; the remote holder clips onto the tester.
-
SCR ELEKTRONIKS
The High voltage tester for routine testing of MCBs combines a conventional high voltage tester with a specially designed robust fixture to hold 20 single pole MCBs at a time. The solution comes as a single trolley with easy-to-set test parameters with safety interlocks designed for user safety with respect to electric shock and mechanical fixturing. An advantage of the system is – it gives a high yield (20 MCBs are tested in about one minute) thus yielding user safety at a high value for money.
-
Model FT2 -
Gopal Electronics
Franklin Tester Model FT-2 is designed as per IS:649 & ASTM:717 Standard to measure insulation resistivity of electrical steel sheet. It requires precision & noise free DC regulated power supply and equally distributed pressure on electrode. Franklin Tester FT-2 regulated power supply provides 0.5000V with 0.1% accuracy over load and no load. Most of national and international standard has specified only 0.5%, means FT-2 is equipped with five time better accuracy than required.
-
Electronic Controls Design, Inc.
Thermal profiling is the recording of time and temperature throughout a thermal process – most often to measure exposure within an oven. Used in many industries, thermal profiling collects data on a product’s thermal transformation experience, which is then analyzed to optimize complex process settings and conditions to ensure quality results. A pioneer in the design of the traveling thermal profiler, ECD has developed a suite of thermal data logging products that serve the electronics, baking, industrial and solar industries, among others.
-
N5249B -
Keysight Technologies
Simplify your test stations by replacing racks and stacks of equipment Increase productivity with the most integrated and flexible single-connection microwave test engine Reduce test time with the world's widest range of single-connection measurement applications Accurately test linear and nonlinear device characterization using advanced error correction Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
193 -
Electronic Specialties Inc.
Relay Buddy 12/24 Pro Test Kit tests five different relays. Relay Buddy is a quick go / no-go tester for the most common automotive relays and this new version tests both 12 and 24 volt relays. . If the relay fails the test, 3 different trouble codes will advise you of the possible causes for the failed relay. The red LED will flash once, twice or three times to indicate the problem. Trouble code definitions are printed on the back of the tester for your convenience.
-
NS1 -
Applied NanoFluorescence, LLC
ANF offers the NS1 NanoSpectralyzer®, a unique automated fluorimetric analyzer based on the most advanced research in nanotube spectroscopy. This patent-pending instrument combines a specialized optical system with custom software to enable efficient, turn-key analyses of bulk SWNT samples. The NS1 NanoSpectralyzer is valuable for tuning the process conditions in SWNT growth reactors, for quality control, for guiding nanotube sorting and separation methods, and for a wide range of research applications that require detailed compositional data on a rapid time scale.
-
IMP20 -
Abaco Systems Inc
The IMP20 video processing mezzanine card significantly increases the ease of acquiring and interpreting images from multiple sensors and cameras, thus speeding reaction time and potentially saving lives. The card adds image fusion capabilities to Abaco Systems’ ADEPT104 and AIM12 automatic video trackers, and allows the design of highly integrated, high performance graphics capabilities in any environment where the input from multiple devices needs to be combined in order to provide a complete, easy-to-interpret image.
-
781314-01 -
NI
The USB‑TC01 is a thermocouple measurement device featuring InstantDAQ technology. InstantDAQ technology includes built-in software for viewing and logging data that automatically loads when you plug in the device, so you can instantly take … temperature measurements with your PC. You can connect the USB‑TC01 to any USB port to use your PC as a display and monitor data in real time. The USB‑TC01 is compatible with J, K, R, S, T, N, E, and B thermocouples.
