Showing results: 1006 - 1020 of 1172 items found.
-
CAPA843 -
Axiomtek Co., Ltd.
The CAPA843, a fanless 3.5-inch embedded board, features quad-core Intel® Celeron® processor J1900 SoC (codename: Bay Trail). A pair of SO-DIMM sockets supports up to 8GB of DDR3L 1066/1333MHz RAM. The compact size embedded board CAPA843 was designed with emphasis on expandability, offering two full-size PCI Express Mini Card slots, as well as an exclusive Axiomtek ZIO connector. With excellent thermal design, the 146 x 102mm embedded SBC can handle operating temperatures from -20°C to 70°C, and runs on +10V to +24V DC input. The 3.5” fanless embedded board provides three display interfaces with dual-display operation: HDMI, LVDS and VGA. The Axiomtek CAPA843 is an excellent choice for applications in IoT/M2M-related, industrial control, self-serve terminal, gaming, digital signage, POS, and kiosk.
-
Recon® V Ultra Lite -
Teledyne FLIR
Fully operational at less than three pounds, the breakthrough Recon V Ultra Lite provides mid-range target detection, recognition, recording and geo-location with an HD color camera and high sensitivity thermal channels. Powered by commercially available AA batteries, the unit has a run time greater than two and a half hours with smart power management. Combining with a highly accurate laser range finder, GPS, digital magnetic compass and intuitive user interface, targets can be quickly located 24/7.
-
Acopian Technical Company
*Universal input.*Power Factor Correction.*Output Inhibit*Constant voltage and constant current modes.*Voltage and current monitor terminals.*Voltage and current programming capabilities.*Short circuit and overload protection.*Thermal protection.*Low Profile.*No minimum load required.*Adjustable down to 0 volts (‘Wide Adjust’ models).*Internal EMI Filter and RFI Shielding.*Pluggable connectors for input and control wiring.*Remote Sensing.*‘Vout OK’ signal monitor.*‘Soft start’ operation.
-
Ironwood Electronics
Ironwood has the most comprehensive collection of BGA (Ball Grid Array) sockets that can be used for prototype application, silicon validation, system development, thermal characterization, burn-in application, functional production test, etc. BGA socket can be defined as an electromechanical device, which provides removable interface between IC package and system circuit board with minimal effect on signal integrity. BGA sockets for prototype applications, silicon validations, system development applications uses low cost elastomer contact technology.
-
Communications & Power Industries
The CPI TMD high-voltage power supplies offer many features desirable for modern radar and electronic warfare applications: high efficiency, ultra-low voltage ripple (low noise), high inverter frequencies, ultra-low pulse-to-pulse jitter, low throughput delay and high power density. The units are lightweight and compact with excellent thermal management, and the high-voltage sections are encapsulated with an oil-free, silicone-based compound. This provides excellent protection in harsh environments while also enabling easy maintenance.
-
TMD Technologies Ltd
Our high voltage power supplies offer many features desirable for modern radar and EW applications; high efficiency, ultra low voltage ripple (low noise), high inverter frequencies, ultra low pulse to pulse jitter, low throughput delay and high power density. The units are lightweight and compact with excellent thermal management and the high voltage sections are encapsulated with an oil free, silicone based compound. This provides excellent protection in harsh environments but also enables easy maintenance.
-
FAB208 -
Axiomtek Co., Ltd.
The FAB208 has a PICMG 1.3 CPU card slot, one PCI Express x16 slot, and a total of six 32bit/33MHz PCI slots. The onboard 24-pin ATX power connector and 8-pin connector for thermal detected board are featured. Furthermore, the backplane supports two high speed USB 2.0 ports. The FAB208 is optimized to support AXIOMTEK's PICMG 1.3 system host boards, the SHB100 and SHB110. We have two enclosures, the AX60551 and AX60552, to house the backplane.
-
HAB208 -
Axiomtek Co., Ltd.
The HAB208 has a PICMG 1.3 CPU card slot, a PCIe x 16 slot and a total of six 32bit/33MHz PCI slots. The onboard 24-pin ATX power connector and 8-pin connector for thermal detected board are featured. Furthermore, the backplane supports two onboard SATA ports (optional function). The HAB208 is perfect fit for AXIOMTEK's half-size CPU cards, the SHB210 and SHB211, which are built around the PICMG 1.3 form factor. We have enclosures, the AX60551 & AX60552, to house the backplane.
-
HAB206 -
Axiomtek Co., Ltd.
The HAB206 has a PICMG 1.3 CPU card slot, a PCIe x 16 slot and a total of three 32bit/33MHz PCI slots. The onboard 24-pin ATX power connector and 8-pin connector for thermal detected board are featured. Furthermore, the backplane supports two onboard SATA ports (optional function). The HAB206 is perfect fit for AXIOMTEK's half-size CPU cards, the SHB210 and SHB211, which are built around the PICMG 1.3 form factor. We have an enclosure, the AX60501 and AX60530, to house the backplane.
-
upj10 -
KEYCOM Corp
KEYCOM''s cryogenic millimeter-wave / microwave test fixtures and calibration kits are specifically optimized for testing the performance of patterns between the edges of printed boards(edge type) and circuit testing on the printed boards(probe type). They are also designed to minimize heat capacity by miniaturizing their dimensions so they cool off efficiently, and materials with low coefficient of linear thermal expansion such as invar are used for major parts where high dimensional stability is required. Their operating frequency ranges from DC to 110GHz.
-
Thorlabs, Inc.
Thorlabs' photodetectors are capable of detecting light throughout the UV, VIS, NIR, IR, and THz spectral regions. Our photodetectors feature sensors that enable properties such as intensity, power, intensity distribution, wavefront shape, energy, and wavelength to be measured. We offer unmounted photodiodes as well as amplified, biased, and avalanche photodetectors. Thermal power detectors are available unmounted, mounted on a PCB, or mounted on an aluminum plate. Also available are position-detecting sensors, integrating spheres, and an acoustic detection module.
-
TopLine Corp.
Daisy Chain provides engineers with a simple tool to learn valuable information about causes of failures. Such failure analysis paves the way for scientists and engineers to improve assembly processes. Critical applications involving environmental life cycle testing require daisy chain packages with dummy silicon die. The Daisy Chain permits electrical continuity testing, while the dummy silicon die replicates the thermal mass of a "live" device. Si Die, QFN, Lead Frame Packages and BGA devices and more.
-
ThermoVision™ (THV) 3000 MultiSensor -
Teledyne FLIR
The ThermoVision™ (THV) 3000 detects and classifies illegal activities and threats in total darkness, smoke, sand haze, and broad daylight conditions. The thermal camera is equipped with a long-wave, cooled Quantum Well Infrared Photodetector (QWIP) and switchable optics offering three different fields of view. It provides excellent situational awareness while also closely monitoring suspect activities in real-time. Ideal applications include perimeter security, border and coastal surveillance, force protection, and mid-range threat detection.
-
OVTT 18 -
Qualmark Corporation
The OVTT, Omni-Axial Vibration Table Top system, is the first, stand-alone, compact, repetitive-shock vibration system on the market. The OVTT 18 system is ideal for No Fault Found (NFF) precipitation screens of field returns, repair verification and random vibration test of small products. The OVTT 18 utilizes Qualmark's patented six-degree-of-freedom vibration technology and is designed with reduced air requirements and low noice levels. The OVTT 18 system can be easily configured for placement inside a thermal chamber for combined stress tests.
-
FLIR EM54 -
Teledyne FLIR
The FLIR EM54 is ideal for inspecting and troubleshooting HVAC/R ducting systems within residential, commercial, and industrial facilities. This meter can help you verify that duct inlets and outlets have the specified volumetric flow – a prerequisite to an efficient functional system. Featuring humidity, wet bulb, and dew point functions, the EM54 can measure deviations from proper relative humidity levels. Plus, the included Type-K contact temperature probe is useful to check electric motors and thermal equipment components for proper operating temperatures.
