Showing results: 736 - 750 of 1171 items found.
-
MTI Corp.
designed for the battery thermal abuse test for IEC62133-8.2.2. The fire-proof dual-chamber has dimension 10" x 10" x 8", which can be heated up to 180°C via an independent temperature controller with +/- 1°C accuracy.
-
F900 -
ASL
The Model F900 is designed specifically for resistance thermometry to provide you with the best possible accuracy. The 25Hz or 75Hz operating frequency provides fast, continuous measurement with high immunity to thermal emfs and supply frequency noise sources.
-
thermVIEW -
Advanced Thermal Solutions, Inc.
thermVIEW is a high resolution liquid crystal thermography system for cost effective temperature measurement of electronic circuit boards, micro circuits, hybrid components and integrated circuits. One micron level* thermal mapping of electronic devices.
-
ThermoVision SS -
Teledyne FLIR
The SS camera is a vehicle camera system for driver's vision has a horizontal field of view (FOV) of 55 or 90 degrees. The SS system is based on an uncooled thermal camera to provide good situational awareness day and night.
-
CERTO series -
Heidenhain Corp.
*Interferential scanning principle*Very high system accuracy of down to ±0.03 µm*Well-matched ball-bearing guide for very high quality*Defined thermal behavior*Large measuring ranges of up to 60 mm*Interface: 11 µAPP
-
Iris Power LP
Rotor magnetic flux variations are the result of the degradation of the rotor winding insulation by mechanisms like load cycling, thermal aging and contamination. Iris Power provides solutions for measuring the magnetic flux in the generator in order to plan maintenance requirements.
-
QuadThermoVault -
MadgeTech, Inc
The QuadThermoVault is a four channel thermally insulated, battery powered, oven temperature data logger able to withstand extreme temperatures. It can withstand oven temperatures of up to 662ºF for up to 25 minutes when properly sealed. Its stainless steel enclosure and thermal properties lend itself to be the ideal temperature data recorder for applications such as powder coating cure ovens, wet coating cure ovens, batch ovens and conveyor ovens.
-
Inframet
TRAL test station is a quasi-universal test station designed to measure parameters of discrete (or small linear array) infrared detectors sensitive in a wide spectral range from about 700nm to about 16 000 nm (NIR/SWIR/MWIR/ LWIR detectors or broadband non selective detectors). All main types of infrared detectors can be tested: photonic detectors: photovoltaic/photoreconductive, cooled/non-coooled, thermal detectors, pyroelectric detectors etc.
-
FLIR K55 -
Teledyne FLIR
With a FLIR K55 TIC in hand, you can attack fires more strategically, maneuver through smoke more easily, and save lives. The K55 displays crisp thermal images on a bright LCD, helping you navigate better and expedite critical decisions. The 320 x 240 pixel IR sensor and FSX™ Flexible Scene Enhancement produce detail-rich imagery at a 60 Hz frame rate that keeps up with the action.
-
AQMS-550 -
Focused Photonics Inc.
AQMS-550 is equipped with an internally mounted catalytic converter set at 315°C to convert H2S to SO2. Bypassing the sample through an SO2 scrubber which removes any SO2, the H2S is converted to SO2 using this internal H2S converter and measured using the pulsed fluorescence technique.AQMS-550 H2S analyzer adopts UV fluorescence principle with an internal thermal catalytic converter to measure H2S in ambient air at levels commonly required.
-
DefendIR -
Teledyne FLIR
The Ranger® MS-UC DefendIR is an industry-leading mid-range thermal imager that can see in complete darkness and through a multitude of environmental conditions, including smoke, rain, snow, dust, and dense fog. The Ranger DefendIR is ideally suited for day and night perimeter security, maritime surveillance, and DHS/DoD applications. The ruggedized housing is environmentally sealed and certified to meet NEMA4X and IP66 specifications, standing up to the most challenging weather and temperature conditions.
-
F9 Systems, Inc.
This ATCA compatible design offers the flexibity to verify the thermal characteristics of your Advanced TCA chassis, logic cards and backplane designs. Used in conjunction with the ThermalBlade the RTM emulates a typical rear mounted logic card. Application component heights and features, airflow resistance and enclosure power dissipation can be evaluated and analyzed.Maximum sustainable watts are 113 with two switches turned on. Watts are dissipated throughout the entire RTM ThermalBlade equally.
-
SEN-30001-KDP -
Playing With Fusion Inc
Breakout board for the MAX31855K digital thermocouple interface IC. Measured temperature range is -270C-1372C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header and four mounting holes for standoffs and 4-40 screws. It does not contain a mini thermocouple connector.
-
SEN-30001-JDP -
Playing With Fusion Inc
Breakout board for the MAX31855J digital thermocouple interface IC. Measured temperature range is -210C-1200C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header and four mounting holes for standoffs and 4-40 screws. It does not contain a mini thermocouple connector.
-
SEN-30001-K -
Playing With Fusion Inc
Breakout board for the MAX31855K digital thermocouple interface IC. Measured temperature range is -270C-1372C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header, has a vertical mini thermocouple connector and four mounting holes for standoffs and 4-40 screws.