Showing results: 8176 - 8190 of 8452 items found.
-
PK-801 Multiple 10-Way PRO -
Pansco, Ltd
The multiple 10-way PRO combines the functions of a 10-way COAX cable mapper and LAN cables identifier that enables identification of a group of improperly labeled patch cables quickly and effortlessly. It also built-in 2 selectable Net/Tel tones for tracing active Ethernet cables even when connected at a switch or Router and locating live phone line systems. This unit also with the capability to do cable/wires loopback and remote continuity testing and voltage detection and warning on F connector, and auto power off function as well as over voltage protection up to 60VAC in a single unit. It provides 2 different ways of Net Tone and HUB blink (optional) feature to trace and work on a live network. It no needs disconnection cable from switch or server and speed up port identification.
-
700.00 MHZ – 110000.00 MHZ -
MVG
A Compact Antenna Test Range (CATR) allows electrically large antennas to be measured at a significantly shorter distance than would be necessary in a traditional far-field test range. Compact ranges use a source antenna (feed) to radiate a spherical wave in the direction of a parabolic reflector, collimating it into a planar wave for aperture illumination of a Device under Test (DUT). It's lowest operational frequency is determined by the size of the reflector, its edge treatment and the absorbers. The two edge treatments available are serrated edge for general purpose applications, and rolled edge to achieve higher accuracy for special applications. Multiple-feed systems may be used to improve the far-field characteristics. A compact range test system also allows system level testing of a complete device architecture.
-
MPA-100 -
Santec Corporation
MPA-100 is a highly integrated rack mountable model of pigtailed photo-detectors. Multi-channel optical power from MPO or MTP connectors are measured. Photo-detectors of Silicon type for 850 nm range and InGaAs type for 1260 - 1610 nm are available. The detected photo-current is converted into a voltage output using a 16-bit multi-channel DAQ interface. The dimensions are (W) 482.6 x (D) 430 x (H) 44 mm. The highly integrated MPA-100 is available up to 80 channels with an excellent cost performance and small footprint. The MPA-100 is useful for many 40 GbE / 100 GbE applications, such as testing and monitoring of transceivers (SR4, SR10, LR4, and ER4) for data communications, broadband / CATV, and telecommunications. Tap-PD model (Eg. a partial 5 % tapped power detection) is also available with customization.
-
PCE Instruments
A vibration meter is used in manufacturing for machine condition monitoring, product testing and quality assurance. Many machine maintenance technicians use vibration meter devices in tandem with sound level meters to analyze frequency. A vibration meter also can be used in civil engineering to measure the vibration of structures such as buildings, roads and bridges. In addition, specialized vibration meter devices can be used to measure the vibration of the human body. Any vibration meter will measure one or more of the following parameters: vibration acceleration, vibration velocity (speed) and / or vibration displacement.A vibration meter is typically a portable device with a memory for storing measurements. Most vibration meter models feature a built-in data logger for collecting and recording vibration measurement data over time. In this way, vibration measurement data can be acquired with great precision.
-
280x Series -
Xitron Technologies Inc.
With an extended measurement range from micro-amps to hundreds of amps and millivolts to kilovolts, the 2801 & 2802 are the ideal analyzers for standby power or Energy Star testing. In addition to numerical results, the 2801 & 2802 captures waveforms with true 512-point precision. Results and waveforms can be displayed, read via communication ports or sent directly at full resolution to a USB printer. Power and amplitude measurements with an accuracy of <0.1% are automatically synchronized to the fundamental frequency. Peak, RMS, rectified and DC measurements of voltage, current and power are provided including continuous, inrush, startup and history modes, plus an integration mode for W-Hr, A-Hr, VA-Hr as well as integrated average power. (Channels can be operated synchronously or independently on the 2802). The 2801 and 2802 also provide waveform peak and glitch capture modes.
-
280X Series -
Vitrek Corporation
With an extended measurement range from micro-amps to hundreds of amps and millivolts to kilovolts, the 2801 & 2802 are the ideal analyzers for standby power or Energy Star testing. In addition to numerical results, the 2801 & 2802 captures waveforms with true 512-point precision. Results and waveforms can be displayed, read via communication ports or sent directly at full resolution to a USB printer. Power and amplitude measurements with an accuracy of <0.1% are automatically synchronized to the fundamental frequency. Peak, RMS, rectified and DC measurements of voltage, current and power are provided including continuous, inrush, startup and history modes, plus an integration mode for W-Hr, A-Hr, VA-Hr as well as integrated average power. (Channels can be operated synchronously or independently on the 2802). The 2801 and 2802 also provide waveform peak and glitch capture modes.
-
CBG830 -
MicroImage Video Systems
The CBG830 color bar and test signal generators will produce a quality, high definition full field color bar signal compatible with the digital HDMI and DVI-D interfaces. The CBG830 is designed to provide an accurate and affordable signal source for easy testing of displays, cables and systems.The CBG830 will generate a full field color bar signal with eight vertical bars, white through black. This signal is available in a variety of resolutions and refresh rates. TheCBG830 will usually fit in a toolbox with ease and even fit into a pocket. There is also a rack mount kit available as well. Power is provided by a regulated 5VDC source and a small wall plug power module is included with the packaged CBG830 but not with board level products. The CBG830 will have a switch array to select the video standard.
-
JW3224. JW3124 -
Shanghai Joinwit optoelectronic Tech,co.,Ltd
JW3224MPO Optical Power Meter and JW3124MPO Optical Light Source is special for testing MPO fiber. At recent years, as the rapid development of data centre and cloud computing, also with rapid growth of multi fibers” (MPO) requirement. However, on the site of measurement process, traditional single channel Optical power meter with complex measurement and low credibility. Based on this, JW3224&JW3124 MPO products arises at this monment. The product can test the insertion loss of MPO fibers and polarity with only one key, And the integration of a variety of data storage, threshold analysis, data export and other applications，Compared with the traditional instrument, the test efficiency of JW3224 & JW3124 is more than 10 times，it is the best choice for field application of MPO room test、calibration of production line、Determination of polarity.
-
Thorlabs, Inc.
Thorlabs' Mode-Conditioned Light Sources are fiber-coupled LED sources that have an output with a flat-top profile in the far field. Common applications include the testing of multimode fused fiber components as well as verification of modal behavior in fiber-based setups. Standard fiber-coupled LED sources can have a range of output profiles that are usually not uniform and vary from source to source. This can be dependent on emitter orientation, alignment with fiber tip, and connector assembly. These mode-conditioned sources have been engineered to distribute light evenly into all transverse modes, resulting in an equilibrium modal distribution at the output. The front panel includes an adjustment knob to control the power and an output port that accepts 2.2 mm wide-key FC/PC connectors. A DS15 15 V power supply with a location-specific plug is included with each device.
-
ADSE 744 -
ATEQ Aviation
This tester was specifically designed for the new-generation pitot tubes that integrate sensing probes, pressure sensors and powerful air data computer processing to provide all critical air data parameters including Pitot and static pressure, airspeed, altitude, and angle of attack. This Pitot Static tester is designed primarily for flightline use to cover the testing of all barometric and manometric pressure instrument systems. The AoA Channel behaves as a second Ps channel, in order to create a differential pressure between the 2 Ps Channel, allowing to performsimulations of different Angles of Attack. The large touch screen display, with on-screen help, enables all checks to be carried out easily on the flight deck or in the cockpit, by a single operator. The ADSE 744 is robust and housed in amobile weatherproof case. An attached bag contains the pressure hoses and electrical cables.
-
Electronic Systems of Wisconsin, Inc.
ESW's Resistance Wire Bonding System comes equipped with the latest features the market has to offer. Our system is capable of bonding armatures, stators or coils. The on-screen display in our bonder makes it easy to read, track, and record your bonding data. If desired, ESW offers complete electrical testing of the part prior to the bonding sequence as well. This ensures only good parts that have been electrically tested are processed through bonding. It is our duty to make sure you never have to worry about losing important information again. Our Sales and Engineering staff will work closely with you to make sure that a bonding systems will meet your needs. See the slideshow below to see some of our Resistance Wire Bonding Testers.
-
SDL1000X/X-E Series -
SIGLENT Technologies
SDL1000X/SDL1000X-E series Programmable DC Electronic Load has a 3.5 inch TFT-LCD display, a user-friendly interface and superb performance specifications. The SDL1020X/SDL1020X-E models feature an input range of 150 V/30 A 200 W while the SDL1030X/SDL1030X-E have an input range of 150 V/30 A 300 W. The SDL1000X series leads with measurement resolution of 0.1 mV/0.1 mA and the base SDL1000X-E series resolution is 1 mV/1 mA and adjustable current rise times from 0.001 A/μs~2.5 A/μs. For remote communication and control, the SDL series includes RS232/USB/LAN interface types. The SDL1000X series delivers stability over a wide range of applications and can meet all kinds of testing requirements. including: Power, battery/handheld device design, industry, LED lighting, automotive electronics, and aerospace.
-
CANNA Dx™ -
CDx, Inc.
Our first sensor, Canna, will enable you to identify the most important chemicals in cannabis and then relate them to how you feel when using that specific chemical combination. By using MyDx™ to detect THC, CBD, and other cannabinoid and Terpene ratios coupled with an extensive database of countless chemical combinations and their associated feelings, you will finally have the ability to find the best chemical profile that works for you all in one convenient, portable THC tester. By doing so, you also join a growing community of users that test and add new chemical combinations and related feelings each week. This is the perfect cannabis analyzer that allows you to do your own THC testing without the need to go to an expensive central laboratory.
-
SmartPhone D -
Teledyne Marine Real Time Systems
The highly rugged encapsulated SmartPhone D was designed for use with the SmartSource controller, or SmartPhone D system, for real-time monitoring of near-field signatures. The integrated 24-bit digitizer at the sensor element provides the lowest noise interconnect between the phone element and digitizing electronics, eliminating the issues of long signal lines and cross coupling while providing unprecedented signature fidelity at a sample rate of 2 kHz. The unique straight-to-digital design allows more flexibilty in umbilical design by providing digital communications clarity with even the longest of umbilicals. Built-in calibration ensures that the system will always report calibration levels. An on-board disciplined precision oscillator provides PPM-level sample rate accuracy. Built-in testing features and self-monitoring provide the user with instant assessments of the health of the phone.
-
Multidyne
Sometimes you just want to connect everything at once. Recognized worldwide as a leading supplier of fiber-optic solutions, MultiDyne now operates a full-service cable fabrication lab. Our rigorous in-house qualification and testing processes bring greater quality control to our product manufacturing workflow. As a Neutrik COCA member, MultiDyne is one of the few certified assemblers of ruggedized opticalCON hybrid fiber cables. MultiDyne also terminates SMPTE 304M LEMO connectors and offers other tactical cables that easily mate to SMPTE fiber-optic cameras, standard breakout boxes, and our other fiber-optic transport solutions. With all assembly happening in-house by specialized technicians, customers can purchase all components of a complete MultiDyne fiber transport solution - or new cables and assemblies to upgrade existing fiber systems.
