Showing results: 7456 - 7470 of 8452 items found.
-
CMi210 -
Martindale Electric Co. Ltd
A unique insulation clamp meter for the installation, testing and maintenance of domestic and industrial installations. This high specification clamp meter can perform insulation tests to 6G Ohms with 5 test voltages from 50V to 1000V.
The clamp provides True RMS measurement of AC current to 1500A and AC voltage to 750V. It will also measure DC current to 2000A and DC voltage to 1000V. The CMi210 has all the same test functions you would expect to find on a high specification multimeter with the added benefit of temperature measurement.
-
6900 -
KANOMAX USA, Inc.
Kanomax has developed the most advanced Duct Air Leakage Tester (DALT) for commercial duct systems. It’s designed to be simple to use, accurate, and extremely convenient. The instrument provides step-by-step duct leakage test configuration and automated leakage testing based on the SMACNA HVAC Air Duct Leakage Test Manual, and is accurate to ±2.5% of reading. Though built tough with an on-board, powerful motor, the DALT 6900 is very easy to transport on its pneumatic tires and leaves little to no footprint on the job site.
-
Wuhan Sunma Technology Co., Ltd.
QAM Analyzer designed for both installation and maintenance of HFC system. Measure and display main parameters in DVB testing (channel power, MER, BER, Constellation Diagram), signal level on any frequency, amplitude of the carriers singly in the whole system range, and etc. The Analog, QAM and FM channel can be set and tested efficiently; it also supports HUM measurement, C/N measurement, voltmeter function, spectrum analysis and data logging. Also it is easy for user to obtain a report of test data via PC or printer through toolbox software.
-
Dynas3 -
HORIBA, Ltd.
Dynas3 Machines are specially suited for use in engine test stands. The AC machine, variable frequency drive with test stand controller and safety module are tuned to one another to form a system that has proven itself many times over. It can be used in any type of development and function test stand. The applications range from simple test stands for steady state operation up to sophisticated test stands for dynamic test cycles. Nearly every application in the field of engine testing can be performed on a test stand with DYNAS3.
-
CS2-VA -
Chuan Sheng Electronics Co., Ltd.
CS2-VA Voltage/Current Meter is designed with high accuracy measurement, display and communication of 0~600V or 0~10A for DC/AC/TMRS.● ADTEK builds flexible function as like as 3 bank (for multi-range scaling and set point) and 3 external control inputs meet to various testing equipment inquiry.They are also build in 4 Relay outputs, 3 External Control Inputs, 1 Analogue output and 1 RS485 (Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission and communication for a wide range of industrial applications.
-
CS2-RL -
Chuan Sheng Electronics Co., Ltd.
CS2-RL RPM Indicator has been designed with high accuracy measurement, display and communication of pulse (Frequency).The innovation feature is auto-range input from 0.01Hz~ 100KHz (option ~140KHz) and the display resolution will auto-change to show the highest according to input frequency.They are also building in 4 Relay outputs, 3 External Control Inputs, 1 Analogue output and 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission and communication for a wide range of testing and machinery control applications.
-
TA-3400 -
Tech-Aid Products
This transponder test fixture is specific to the requirements for testing Becker Avionics Transponders and provides interface connectors for both the panel mount and remote systems. The panel also provides switches to implement Gillham code altitude as well as separate interfaces for an external parallel or serial encoder. The panel will interface with the RMU 5000 or standard control head. This fixture also comes with voltage and current meters along with an internal dimming source. This panel comes in the standard 19 inch rack width and measures 12 inches in depth.
-
Eaton Corp. Electrical Group
Eaton is a world leader in delivering an unsurpassed range of reliable, efficient fuel systems for today's commercial and military aircraft and aero-engine programs. Eaton's aerospace fuel systems portfolio includes fuel pumps, boost and transfer pumps, valves, sensors, and accessories, as well as all the components to build fuel conveyance and delivery sub-systems from the tank to the engine. Eaton's premier fuel system testing facility in Europe provides a total system capability certification for the design and development of fuel systems to suit our customer's specific requirements.
-
SGT-200 -
Manta Test Systems
The Vanguard SGT-200 Safety Ground Tester is a 200A DC micro-ohmmeter designed specifically to measure the resistance of protective in-service grounding and jumper cable assemblies. The SGT-200 can measure the resistance of the grounding cables, clamps and ferrules. The measured resistance values can be compared against the calculated values (using the ASTM 2249-03 standard) and a Pass/Fail result can be printed along with the measured resistance values. Since the SGT-200 uses a DC current, there is no need to uncoil the cable under test. It can be conveniently tested in its coiled state in a much smaller testing enviornment.
-
L-RF-MN-RX -
QuestTel
The QuestTel''s L-RF-MN-RX module optical receivers are versatile, low-cost and compact optical receivers for use in HFC fiber applications. It is perfect solution for the transport and distribution of CATV RF signals over fiber optic cable. The L-RF-MN-RX module housed in a small housing and have adjustable RF output level. May be used as a hand held device for testing, or placed at a customers premise for the reception of cable television services. The Receiver is designed to operate with a very low optical input level between the range of +3dBm to -12dBm.
-
ET Power Systems Ltd.
The electronic AC loads cover a wide variety of different voltage, current and power ranges. All the AC loads are programmed with 11 different sine, square and DC waves. With 5 crest factor variations of each, a total of 55 waveforms are available. An external input is also provided to enable the user to amplify signals from a waveform generator.AC Loads allow real world operating conditions to be simulated. Typical applications include circuit breaker, transformer & UPS output testing along with general laboratory and research work.
-
CKT1175-10 -
CK Technologies, Inc.
Designed for wiring testing requirements requiring up to 2,000 test points, the CKT1175-10 is ideal as a benchtop or portable test system. The system is packaged in an enclosure specifically designed to be used in rugged environments. The basic 500 test point system is 20.5 in. (521 mm) wide X 12.0 in. (305 mm) high X 16.05 in. (408 mm) deep; the 500 test point expansion units are 20.5 in. (521 mm) wide X 6.00 in. (153 mm) high X 16.05 in. (408 mm) deep.
-
KT-5000Pi -
Kast Eng Co. LTD.
This is a Hipot(Puncture) Tester combined with Insulation Tester in a set.It tests 2 kinds of test continuously in sequence, and any of both hipot or insulation test can be set to test first in other by the selection switch.Hipot Tester has the leakage current meter, so the operator can check the leakage value while testing. And the preset procedure of the Insulation Tester is very easy. Both tester judge the product to be good or bad automatically in a short time.This tester has many I/O ports to connect extra test system. Price : 2,550 (USD)
-
KD-163 -
King Design Industrial Co., Ltd.
*Comply with IEC-68-2-29 testing specification(10g/ 16ms、15g/6ms、 40g/6ms、100g/2ms).*Easy installation and simple operation; Low noise; no maintenance required; function holds long.*Well-designed and no resonant-structure, air anti- vibration pad can effectively isolate floor vibration.*Accelerometer adopts repeated measurement and adjustable half-sine wave generator; to control the data is precise.*Magnesium alloy platform is anodized, Servo motor cam to drive, and can adjust the frequency automatically.*The adjustable acceleration value and shock domain is patent design (1ms-13ms).
-
Monoxor XR -
Bacharach, Inc.
The Monoxor® XR is a portable exhaust gas analyzer designed to measure high CO from forklifts and other combustion engines for compliance testing (OSHA, CCOHS). View and save your CO readings in real-time from the numerical or graphical display screens. The Monoxor® XR is available with pre-calibrated, B-Smart® sensors to minimize downtime and maintenance costs. The analyzer is also compatible with Bacharach’s Combustion App which allows users to quickly create / share custom reports (available for Android & iOS).
