Showing results: 3136 - 3150 of 5297 items found.
-
780588-01 -
NI
Non-Enclosed, 300 Vrms, 50 kS/s/ch, 24-Bit, Simultaneous Input, 3-Channel C Series Voltage Input Module - The sbRIO‑9225 performs differential analog input. The wide measurement range is well suited for high-voltage measurement applications such as power metering, power quality monitoring, motor test, battery stack testing, and fuel cell tests. You can perform transient and harmonic analysis with high-speed simultaneous sampling. In addition, you can prevent ground loops and add safety to a system with 600 Vrms channel‑to‑channel isolation between the three sbRIO‑9225 channels. Non-enclosed modules are designed for OEM applications.
-
S930702B -
Keysight Technologies
S930702B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 26.5 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930702B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
S930705B -
Keysight Technologies
S930705B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 50 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930704B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
S930701B -
Keysight Technologies
S930701B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 13.5 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930701B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
S930704B -
Keysight Technologies
S930704B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 43.5 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930704B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
S930713B -
Keysight Technologies
S930713B enables fast and accurate active-device modulation distortion characterization under modulated stimulus conditions up to and beyond 125 GHz. The wide dynamic range and vector error correction of the PNA-X results in an extremely low residual EVM of the test setup, delivering you a complete picture of your device’s performance without test system interference. S930713B measures EVM, NPR, ACPR, and decomposes nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
SG-YD -
Wuhan Sangao Electrical Test Installations Limit Co.
AC and DC test oil immersed transformer.Traditional oil immersed test transformer is used to do power frequency withstand voltage and DC current withstand voltage test for variety kinds of high voltage electric device, insulating material.YD series oil transformer, also known as test booster, which test insulation strength under specified voltage for various electric products, components, insulation materials. It can test products insulation level, find insulation defect and judge overvoltage ability. It is widely used in power station, power supply and distribution system and research institute.
-
PFX2500 Series -
Kikusui Electronics Corp.
PFX2500 Series is a high performance Charge/Discharge system controller that takes measurements in combination with our DC power supply and electronic load in order to evaluate test sample (electric storage elements such as secondary batteries) characteristics. It is also capable to perform evaluation test with high-performance, large capacity and wide range of rating with the combination of DC power supply and electronic load.Execution of the test is conducted by the exclusive application software. The test corresponds to long time continuous test and synchronization test with temperature chambers with the multiplexed protection performance. In addition, easy data editing is also capable with fulfilling graphic performance.
-
ETL-35 -
Kharkovenergopribor Ltd.
ETL-35 is a cable test van designed for testing electrical substation equipment.Apart from cable insulation withstand testing with DC (rectified) voltage up to 60 kV and ability to measure very small leakage currents, the system can be used for testing various objects with small electrical capacitance with AC voltage of up to 100 kV and measuring dielectric dissipation factor (Tan Delta) at industrial frequency.
-
Venture -
SV Probe, Inc.
SV TCL's VentureTM line of cantilever probe cards, represents the finest epoxy technology on the market and are perfect for logic testing. The Venture line includes an extensive array of cantilever cards, single to multi-die for a variety of test systems. Our Venture FX™ fine pitch cantilever cards are ideal for LCD driver testing, with higher probe counts for greater density bond pad layouts.
-
Electro-Tech Systems, Inc.
Standard Environments: ETS' multi-purpose benchtop units for laboratory and production use are large enough to accommodate testing and fabrication, as well as storage of materials, test equipment, and assemblies, yet they are small enough to fit on a standard workbench. The systems are able to independently maintain humidity from <5% to >95% RH and temperature from -22F to 122F (-35 to 50C) when unit is placed in an ambient environment location.
-
LMS SCADAS -
Siemens Digital Industries Software
The LMS SCADAS state-of-the-art data acquisition systems cover all types of noise, vibration, durability testing and engineering tasks in the lab, in the field, with a PC or through autonomous recording. Seamless integration with LMS Test.Lab and LMS Test.Xpress provides you with reliable results and optimal testing productivity. Take your mind off the deadline and focus on the test. From lab to mobile to portable.
-
Process & Analytical Instruments division of AMETEK
Measurement Communications & Testing provides the design, integration and installation of critical communication systems, workflow, life-safety solutions and calibration instruments for temperature, pressure and process control. It also is a leader in level measurement devices, continuous position sensors, hardness testers, force measurement devices and retractable cord reels. In addition, it offers a line of weathering test instrumentation along with laboratory and outdoor testing services.
-
Catena 1910 -
MCCI
The MCCI Catena 1910 HSIC USB Tester enables testing of HSIC Host or HSIC Device products. It can be used to exercise your product by operating as an active host or active device, while simultaneously capturing USB traffic for analysis. For test and validation of a final system, Passive Capture mode lets you debug and verify communication between your HSIC Host and HSIC Device,
-
Pickering Interfaces Ltd.
Our PXI Millivolt Thermocouple Simulator modules provide 32, 24, 16 or 8 channels of accurate low sources. They are ideal for the simulation of thermocouples and can be used for sensor emulation in ECU testing. The channels can be operated with one of three voltage ranges covering most thermocouple types. We can also supply connection solutions allowing the easy integration of the Thermocouple Simulator into your test system.
