Showing results: 406 - 420 of 592 items found.
-
133 -
STAR-Dundee
The SpaceWire Router Mk2S is a routing device that provides the essential capabilities now demanded of SpaceWire test and development equipment. The SpaceWire Router Mk2S provides eight SpaceWire interfaces, the ability to act as a time-code master, support for high speed data transfer, the capability to inject various types of errors on demand, and comes complete with highly optimised host software support for low latency transmission of SpaceWire packets directly to and from the host PC.
-
Langer EMV-Technik GmbH
Used for EMI suppression in printed circuit boards during the development phase. The developer can use the E1 set to quickly identify the causes of burst and ESD interference. This allows the developer to design suitable measures to solve the causes of the interference. It can also be used to test the effectiveness of the measures taken.
-
Keysight Technologies
Keysight’s industry-leading range of wireless network emulators and device test solutions enable the entire mobile device ecosystem to accelerate the market introduction of new wireless devices by streamlining the workflow from early prototyping, development, and design verification to conformance, carrier acceptance, and high-volume manufacturing.
-
PT-LabCar -
ETAS GmbH
PT-LABCAR is an open and scalable Hardware-in-the-Loop (HiL) system. It is designed for open- and closed-loop testing of ECUs specifically in the powertrain application domain. The system can be used to run automated regression tests for the release of software variants as well as for the validation of control and diagnostic functions in early phases of ECU development.
-
LCS-3 -
PENKO Engineering B.V.
Load cell simulator particularly useful in a test environment for example to check a program sequence of a controller. The LCS-3 is a simulator used as a substitute for strain gage transducers to generate the precise mV/V signals required in the development , checkout and pre-calibration of signal conditioners, digital and analog readouts and data loggers.
-
BMS HIL -
Bloomy Controls, Inc.
The BMS Hardware-in-the-Loop (HIL) Test System is a high performance platform providing all necessary input signals used for battery pack simulation. A real-time operating system executes complex cell and pack models commonly used for BMS algorithm development and firmware regression testing.
-
ESP -
ARC Technology Solutions
ESP, or Engineering Support Platform, is a low cost, powerful and versatile platform for the development, deployment and support of FPGA Applications. ESP is powered by DSX core, ARC’s core element for the development and deployment of digital and mixed signal systems. The standard system contains 2 custom FPGA system, often configured in combination where one acts as the application firmware, and the other is used for test. But the system is expandable and configurable in any combination to solve any problem in a digital, analog or mixed signal system. The FPGAs can be configured to generate, analyze, process and/or output complex signals at a wide range of voltages, frequencies and serial protocols. It has been used to develop solutions for Radar systems, testers, Pattern Generation, digital signal processing and generating, Video processing, and many more. ESP comes as a desktop or rack mounted solution, and no special interfaces are needed.
-
DST200 -
Rohde & Schwarz GmbH & Co. KG
The R&S®DST200 RF diagnostic chamber is the ideal environment for RF analysis during development. It supports a wide range of radiated test applications for wireless devices and fits on any R&D lab bench, where it can be used at all times during the product design and optimization phase. The R&S®DST200 effectively assists in achieving high first-time pass rates during final type approval, which saves time and money.
-
T3SA Series -
Teledyne LeCroy
Teledyne Test Tools new T3SA3000 family of Spectrum Analyzers offers a frequency range of 9 KHz to either 2.1/3.2 GHz alongside many impressive features. With their light weight, small form factor, and user friendly interface, these Spectrum Analyzers take powerful and reliable automatic measurements that are presented on a large, bright, easy to read touch screen display. Typical uses for the T3SA3000 series are research and development, education, production, maintenance, and pre-compliance testing.
-
WT Dyno -
HORIBA, Ltd.
Our WT series eddy current dynamometers are mainly used in the development and testing of all types of prime mover, as well as various engine assemblies. Due to their robust design, which incorporates improved control characteristics, they can be used both as steady state and as transient test stands.Their high speeds for automobile engine testing and their optimised cooling chamber, are convincing arguments that speak for themselves. All WT type dynamometers are suitable for operation in both directions of rotation.
-
ScanDIMM -
Corelis, Inc.
Maximizing test coverage is an important piece in test procedure development. Unfortunately, not all designs have the necessary requirements in place to accommodate boundary-scan test methods on memory devices. ScanDIMM digital socket test modules are designed to overcome such limitations when testing DIMM sockets utilizing boundary-scan test techniques.ScanDIMM modules provide the capability to instantly turn any DIMM socket into a fully compliant IEEE-1149.1 device. Integration is as simple as assigning the included BSDL file to the reference designator of the target socket and compiling test vectors.In multi-socket systems, multiple ScanDIMM modules can be linked to provide even greater boundary-scan test depth.
-
NI
The Software Platform Bundle provides the entire NI software portfolio for building any application. Develop applications in multiple environments, including LabVIEW Professional, LabWindows/CVI, and Measurement Studio. Extend the functionality of the LabVIEW development environment with all add-ons to perform code deployment, hardware integration, data analysis, and code validation. Build automated test systems with TestStand and real-time test systems with VeriStand.
-
Sample Technology
The need for microwave test and measurement technology is even more urgent than the need for microwave equipment itself. Therefore, Shengbo Technology is relying on its own research and development capabilities to strive to become one of the comprehensive microwave test and measurement equipment suppliers. We provide a wide range of RF microwave test products, including a good-quality full-band broadband up-down converter . You can provide 2GHz real-time bandwidth signal up-down conversion function in the frequency range of 0.1 ~ 40 + GHz. With our channel simulator , we Became the first company in the world to provide channel analog solutions in such a wide range of broadband signals. At the same time, we are also an innovativesupplier of noise sources and multi-channel microwave signal sources in the industry.
-
Eastern-Optx
Eastern OptX now offers System Integration for all of our equipment along with other instruments including: RF, microwave, and Optical test equipment, power conditioning, distribution, and back-up, system controllers, and data recording devices. We also offer test solution development including mechanical design, rack layout, and custom control software. Eastern-OptX will help you to design and develop your test solution and deliver a completely assembled and tested system.
-
RT2 -
ETAS GmbH
ETAS RT2 is a powerful test tool for testing of functional models (MiL) and software (SiL). It contains the following parts of the testing lifecycle: modeling, execution, assessment, and reporting. ETAS RT2 is specialized for testing of embedded systems with inputs and outputs of continuous or discrete signals. A model based test design approach enables intuitive realization of complex test strategies. Thanks to its capabilities ETAS RT2 enables comprehensive testing activities in the early phases of the development.
