Filter Results By:

Products

Applications

Manufacturers

Test

to find acceptable or limits of.

See Also: Testers, Testing, Specimen


Showing results: 7051 - 7065 of 14526 items found.

  • System Testing

    TestOrigen Software Testing Services Pvt Ltd.

    System testing is basically a sequence of various test performed to check the whole computer-based system. The key objective of system testing is to confirm the system level testing should meet the user’s viewpoint.

  • Intelligent Battery Tester

    CHROME - ACT Meters International Ltd

    Simulating a 20 hour discharge test in seconds, the ACT CHROME displays the DC Voltage and available Ampere hour (Ah) capacity of standby lead acid batteries between 1.2Ah and 200Ah.

  • Headlight Beam Testers

    Van Leeuwen Test Systems BV

    VLT offers a wide range of professional headlight beam testers. From simple manually operated models up to fullly automated robot type machines for use in integrated test lanes.

  • LED 4 Flat Tester

    48655 - Hopkins Manufacturing Corporation

    Quickly and easily confirm if your vehicle 4 flat connector wiring is properly installed and functional. Fits on your keychain to keep it handy! LEDs test left/right turn, brake and taillight.

  • Silicon Nails Feature, GTE 10.00p

    K8214A - Keysight Technologies

    Keysight’s Silicon Nails feature enables all the tools required to develop and execute tests on non-compliant boundary scan devices that are connected to boundary scan compliant devices on the printed circuit board.

  • Silicon Nails Feature, GTE 10.00p

    K8214B - Keysight Technologies

    Keysight’s Silicon Nails feature enables all the tools required to develop and execute tests on non-compliant boundary scan devices that are connected to boundary scan compliant devices on the printed circuit board.

  • Basic Pulsed-RF Measurements Lite

    S95024B - Keysight Technologies

    Using built-in pulse modulators, the PXI VNAs are complete pulsed-RF measurement solutions, eliminating the need for external test sets and pulse generators. Lite version of S95025B Basic Pulsed-RF Measurements.

  • LifeTest Software

    PEC N.V.

    In combination with the extended range of PEC test equipment, LifeTest supports the many specific functionalities required in battery testing labs. Drive cycle simulations (FUDS, DST…), thermal performance tests, high speed pulse tests (HPPT), life cycle tests, accelerated ageing tests and internal resistance measurement tests can be easily configured, scheduled, executed and reported from a single platform.

  • Circuit Breaker Analyzer

    CAT Standard Series - Amperis sl

    The CAT Standard series circuit breaker analyzers & timers are stand-alone or a PC-controlled digital instruments for circuit breakers condition assessments. The timing channels record closing and opening of the arcing, resistor, and auxiliary contacts. CAT Standard series records graphs of both, trip and close coil currents and displacements of the HV and MV circuit breaker moving parts. The main contact channels can also measure the resistance value of the pre-insertion resistors (if present in the circuit breaker). Test results can be downloaded to a USB memory stick or saved to internal memory. The CAT Standard series internal memory can store up to 500 test results (numerical and graphical data). Test results can also be printed on the 80 mm (3.15 inch) thermal printer (optional accessory) in tabular and graphical form. CAT Standard series provides an easy selection of different operational modes:

  • Gravelometer Testing

    National Technical Systems

    Gravelometer testing is designed to evaluate the resistance of vehicle surface coatings (paint, clear coats, metallic plating, etc.) to chipping caused by the impacts of gravel and other flying objects in accordance with SAE and ASTM standards. The primary usage of this test is to simulate the effects of the impact of gravel or other debris on automotive parts. Test samples are typically mounted in the back of the Gravelometer, and air pressure is used to project 1 pint (approximately 300 pieces) of gravel at the sample. The test sample is then removed and gently wiped off with a clean cloth. Tape is then applied to the entire tested surface. Removal of the tape then pulls off any loose fragments of the coating. The appearance of the tested sample is then compared to standard transparencies supplied by SAE to determine the chipping ratings. Visual examination can also be used to describe where in the coating/substrate system that the failure has been induced.

  • Sand and Dust Testing

    National Technical Systems

    NTS operates some of the largest and most accurate sand and dust testing chambers available in the industry. We can accommodate parts in excess of 8 ft3 (0.25 m3) and comply with the requirements of various regulatory standards. While sand or dust circulate at up to 40 mph (65 kph) we can modify the test according to your special requirements, including running at temperatures of up to +200°F (+95°C). A calibrated “hopper” which assures that an adequate amount of contaminant is entering into circulation manages the input to the chambers. In addition to measured inputs, NTS employs an electronic beam, which determines that there is the right mixture of sand or dust and air in the test medium at any given time. This enables our technicians to adjust for loss in real time, and make corrections to ensure that the test article is exposed to the harmful particulate matter for the requisite amount of time.

  • Motor Testing

    Electronic Systems of Wisconsin, Inc.

    ESW's Motor Test Systems come fully equipped with the latest industry features based on your testing needs. The on-screen display in our testers make it easy to read, track, and record your motor information during the testing process. We realize this importance and want to make sure you never have to worry about losing key information ever again. Performance and reliability are important, so we make sure you will have full confidence of every motor you test, whether you place it in your product or send out the door to your customer. ESW's design team works closely with you to determine the tests you need, in order to make a system that will meet all your testing needs. See the slideshow below to see some of our Motor Testers.

  • The Mag Lead

    136 - Electronic Specialties Inc.

    *Mag Lead features a magnetic disconnect near the test probe end. *Just disconnect the test probe and you can “stick” to any metallic ground or test point. *Quit fumbling with alligator clips that fall off - Mag Lead’s powerfull magnet will hold tight! *This is a time saving tool - if you don’t have to walk to your tool box to retrieve your alligator clips, even on just half the occasions, then you’ve saved time. *Very helpful for automotive reference points and troubleshooting. *Can eliminate the need to hold probes while checking or monitoring a signal. *Two high power, low resistance magnets hold the probe to the lead. *Fits almost all Digital Multimeters and can be used with hand-held scopes too. *Get the Mag Lead, it stays put and won’t fall off, like alligator clips do!

  • Flying Probe Testers

    Acculogic, Inc.

    Flying probe test systems require no test fixturing, have few restrictions on board access, and can test boards with virtually unlimited number of nets. These systems also allow developers to complete test programs in a short time.

  • Walk in Explosion-proof Chamber (Auxiliary Equipment)

    Guangdong Bell Experiment Equipment Co.,Ltd

    DGBELL Walk in Explosion-proof Chamber is mainly used to test the safety performance of lithium ion battery, battery pack. Prevent test operators and other test equipment from being burned and exploding. At the same time, the explosion-proof test chamber with the smoke exhaust system can discharge the smoke generated in the test to the outside.

Get Help