Showing results: 1861 - 1875 of 5231 items found.
-
BT-1 -
Physitemp Instruments
BT-1 General Purpose Probe - Probably our best general purpose probe designed for temperature measurement of solids, liquids, gases and semi-solids. Welded stainless-stell shaft, plastic handle. Tip is .028'' diameter bent at right angle to probe to facilitate accurate surface measurements. Immersible. Maximum temperature 240°C, Time constant 0.15 Seconds. 5 foot lead. Not isolated.
-
ST60 Quad -
Dexter Research Center, Inc.
A four-channel silicon-based thermopile detector in a TO-5 package. Each small active area size is 0.61mm x 0.61mm. This is our lowest-cost and fastest time constant four-channel detector. It delivers a time constant of 18ms with Nitrogen encapsulation gas combined with a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
SKZ145 -
SKZ Industrial Co., Ltd
To determine the melt mass-flow MFR /10min, the melt volume-flow rate MFVcm3/10minand the melt density of thermo resin, for the engineering plastics of polycarbonate, nylon and fluorine plastics, etc, whose melt temperature are higher, but also fit for the plastics tests of polyethylene, polystyrene, polypropylene, ABS resin and poly-formaldehyde resin, etc, whose melt temperature are lower, it is widely applied to the fields of plastics materials, product, petrochemical
-
Advanced Science and Novel Technology, Co., Inc.
DC to 25GHz broadband linear signal splitterOne differential CML-type input port and four phase-matched differential CML-type output portsDifferential input linearity range up to 1000mV p-pDifferential gain of approximately -1.5dBLow jitter and limited temperature variation over industrial temperature rangeSingle +3.3V or -3.3V power supplyPower consumption: 1.35WFabricated in SiGe for high performance, yield, and reliabilityCustom CQFP 44-pin package
-
KM 5490 -
Kusam Electrical Industries Limited
• As it uses a high quality oxygen sensor, it is very precise and its performance is stable.• It uses the advance technology design and has multiple functions.• With highlight backlight display and acousto-optic alarming, it is easily configured.• The in built temperature compensation makes the meter measure the correct value of oxygen in the environment temperature of -10 ~ 40�C.• As its case is ergonomically designed, it looks elegant, and is easy to carry.
-
Laser Components IG, Inc.
Pyroelectric detectors are thermal detectors; i.e. they create an electric signal due to temperature changes in the chip. This temperature change is caused by absorption of light. We do use LiTaO3 and DLaTGS as pyroelectric materials. Basically such detectors cover the whole spectra. However, they are mainly used for mid-wave and long-wave infrared detection (MWIR and LWIR). In addition, the usage in the THz region seems to become more popular these days.
-
LT Laser Tools GmbH
Pyroelectric detectors are thermal detectors; i.e. they create an electric signal due to temperature changes in the chip. This temperature change is caused by absorption of light. We do use LiTaO3 and DLaTGS as pyroelectric materials. Basically such detectors cover the whole spectra. However, they are mainly used for mid-wave and long-wave infrared detection (MWIR and LWIR). In addition, the usage in the THz region seems to become more popular these days.
-
ST60 Dual -
Dexter Research Center, Inc.
A two-channel silicon-based thermopile detector in a TO-5 package. Each small active area size is 0.61mm x 0.61mm. This is our lowest-cost and fastest time constant two-channel detector. It delivers a time constant of 18ms with Nitrogen encapsulation gas combined with a very low Temperature Coefficient of Responsivity of -0.04%/°C. This detector has a very short thermal shock response to ambient temperature change.
-
Shenzhen UYIGAO Electronic Technology Co., Ltd
This is an infrared thermal imager that combines the functions of surface temperature measurement and real-time thermal imaging. The traditional thermal imaging camera needs to measure each component one by one, while this instrument does not need to. Therefore, it helps to save your time. Even the potential problems can be clearly displayed on the color screen which helps users quickly locate the central point to measure cursor and temperature.
-
IM2000 Series -
Ajinkya Electronic Systems
We have been offering IM2000 Series Thermocouple Data Logger with direct interfaces for various types like J / K / R / S / T / B / E etc. Loggers have built in ambient compensation. The thermocouples are most commonly used sensors for measuring temperature in process industries. These can take any form and are available in various mechanical shapes. The temperature ranges are varied.
-
T3511 -
COMET SYSTEM, s.r.o.
Web Sensor with relative humidity and temperature probe. The device is supplied with T+RH probe on the cable. High precision capacitive polymer sensor ensures excellent long term calibration stability and ultimate accuracy. Dual line LCD is an advantage. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
T3511-4 -
COMET SYSTEM, s.r.o.
Web Sensor with relative humidity and temperature probe. The device is supplied with T+RH probe on the cable.High precision capacitive polymer sensor ensures excellent long term calibration stability and ultimate accuracy. Dual line LCD is an advantage. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
T3511-2 -
COMET SYSTEM, s.r.o.
Web Sensor with relative humidity and temperature probe. The device is supplied with T+RH probe on the cable.High precision capacitive polymer sensor ensures excellent long term calibration stability and ultimate accuracy. Dual line LCD is an advantage. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
Electronic Equipment Use -
Panasonic Industrial Devices Sales Company of America
Panasonic Film Capacitors offer stable capacitance and temperature characteristics, tight tolerances, low-ESR and low dissipation factors. Available in Surface-Mount (SMT) and radial leaded types, including Metallized Polypropylene Class X2 Capacitors. Functionality offered in the Film Capacitor product line for Electronic Equipment Use include high temperature and high reliability without shock noise, piezoelectric effect and audible noise.
-
AMETEK Sensors, Test & Calibration
We offer a signal multi-scanner which provides a time-saving, automatic solution to calibrate multiple temperature or pressure sensors simultaneously. The scanner may be combined with our dry-block or liquid calibrators, DTI reference thermometers, pressure calibrators, and ASC multifunction process calibrators. Use any place where temperature and/or pressure measurement is critical and there is a need to create traceable documents for sensor calibration.