Showing results: 31 - 45 of 81 items found.
-
Psiber Data Systems
The CableTool uses TDR (Time Domain Reflectometry) technology to quickly identify an open or a short from 0 to 2,500 feet within a foot of the fault.
-
N5225BT -
Keysight Technologies
The N5225BT provides the N5225B 50 GHz PNA, application software including PLTS and Enhanced TDR and accessories for signal integrity evaluation of cables, backplanes, and BGA packages.
-
N5222BT -
Keysight Technologies
The N5222BT provides the N5222B 26.5 GHz PNA, application software including PLTS and enhanced TDR, and accessories for signal integrity evaluation of cables, backplanes and BGA packages.
-
TDR-420 -
Sonel S.A.
TDR-420 is a hand held Time Domain Reflectometer designed to identify and locate faults in power, telecommunications and teletechnical cables. TDR-420 reflectometer allows to measure the length of the cable and determine the distance to damage or impedance variation in the range of 4 m to 6000 m in conductors with metal wires. The shortest measuring range of 7 meters and a dead zone of 0.6 meters allows to locate damages at a very close distance from the place where the device is connected.
-
TDR-410 -
Sonel S.A.
*Location damaged power cables.*Fault location copper telecom cables.*Coaxial cable fault location.*Fault location wiring infrastructure.*Detection of breaks, short circuits, damage caused by dampness and other changes in impedance of the cable.*Graphic depiction of damage the cable with automatic indication the distance to fault on the screen.
-
Neutronics Manufacturing Co.
The NMC 'TDR' is a high precision, new generation, light weight large output current and micro-processor controlled tester. This replaces old DC wheat stone bridge and double arm bridge for measurement of DC resistance. 'TDR' adopts new advanced test current power supply technology, four terminal measurement, digital display of resistance value and test current. 'TDR' is powered by 220V AC mains single phase supply. The measurements are accurate as the test current is highly stable. High automation is achieved with automatic discharge warning.
-
Neutronics Manufacturing Co.
Measure DC resistance of transformers windings etc. Introduction: The NMC ''TDR'' is a high precision, new generation, light weight large output current and micro-processor controlled tester. This replaces old DC wheat stone bridge and double arm bridge for measurement of DC resistance. ''TDR'' adopts new advanced test current power supply technology, four terminal measurement, digital display of resistance value and test current. ''TDR'' is powered by 220V AC mains single phase supply. The measurements are accurate as the test current is highly stable. High automation is achieved with automatic discharge warning.Principle: The constant current generated is fed to the resistance under test through the current terminals and the voltage drop across the resistance under test is measured and displayed in ohms. A true four terminal measurement is used to eliminate the need for lead resistance compensation.
-
RoBAT RCI -
RoBAT Ltd.
*TDR & TDT, Measurement Capabilities*Impedance, Skew, Backdrill measurements*Automated Optical Inspection*DC Electrical Test*Now available with 4 heads*24 port (1 port per channel) TDR/TDT unit*Future capabilities – Fully automated VNA test (4 port S-Parameter Measurement)
-
Material Sensing & Instrumentation
Microwave cavity characterization complements TDR Dielectric Spectroscopy in low-loss materials, providing high-resolution permittivity and loss data at specific single frequencies. Since measurements do not change significantly with frequency in low-loss materials (Kramer-Kronig relation) cavity measurement at select frequencies provides a full characterization across the RF/microwave range.
-
ECAD System 2005 -
CM Technologies Inc.
The ECAD System 2005 is a suite of test instruments for both lumped and distributed data for analysis of electrical circuits and/or wiring harnesses. ECAD is completely self contained, and has a built-in multimeter, impedance meter, TDR, and megohmeter.
-
CITS880s -
Polar Instruments Inc
Finer geometries and thinner copper can present a challenge for fabricators measuring impedance on leading edge PCBs. The CITS880s answers that challenge with the introduction of Launch Point Extrapolation (LPE). LPE extrapolates the TDR response back to a point close to the start of the transmission line effectively allowing to users more accurately to measure the instantaneous or incident impedance of the line.
-
CZ20154 -
Aegis Pty. Ltd.
The CZ20154 is the top of the range in latest design technology providing voice, data, and video technicians/engineers all the functionality essential in a test set. Buttinskis are now required to deal with modern high speed digital services - something this test phone has been specifically designed for. On top of all the tests performed by the CZ20123, TDR length measurement to 900m is included for the first time on a buttinski. Not only can you measure cable length but you can identify the fault location of an open or a short. Further, tone generation is included as standard providing 5 different search tones and SmartToneR that confirms you have located the correct pair. Never before has this level of features been available in a buttinski. No longer do you need to carry a separate butt set, TDR, toner, and identifier - this buttinski does it all in the one tool !
-
CZ20050 -
Aegis Pty. Ltd.
Telecommunications, Electrical, Data, and Video installers should all have a TDR in their toolkit. From measuring the length remaining on a drum to knowing exactly where to dig to find that cable fault the Cable Gauge can be invaluable. Opens, Shorts, and length are all measured by the metre letting you know how much you have or where the issue is. Stocktaking of cables is made simple using the Cable Gauge. Using TDR technology, the Cable Gauge diagnoses cable faults with no launch or dead zone at an accuracy of ±2%. Simply select the appropriate cable type from the pre-stored library or enter the cable NVP, attach the leads to two conductors of the cable and with a single press of a button the length of the cable or distance to an open or short is displayed. Voltage on the wires up to 250v is continuously measured by the built in, true RMS voltmeter and is displayed to warn of a potentially unsafe condition.
-
HL1100 Series -
Hyperlabs, Inc.
HYPERLABS HL1100 Series TDR instruments provide high-performance test and measurement capabilities for use in the field or in the lab. These instruments are used for applications such as fault detection in cables and interconnects, impedance characterization, time of flight analysis, water level measurement, and more.
-
#TXG200 -
NSI Industries
*Ethernet Speed certification of copper and fiber optic systems up to 10Gb*Complete active network testing over copper, fiber and Wifi systems*Cable qualification to IEEE standards*TDR & fiber cable length measurement*PoE testing up to 90W (PoE++)
