Standards
A controlled reference or acknowledged technical criterion.
See Also: IEC, IEEE, Mil, Interoperability Test, Compliance
-
product
Liquid Level Sensor
LevelMaster
The LevelMaster combines the industry’s most innovative hardware and software to address the unique custody-measurement and operational needs of tank-level management. The LevelMaster provides not only an accurate level gauge, but also an accurate measurement of the oil and water interface.Unlike other level-sensing technologies, LevelMaster provides precise levels without having to continuously adjust for changes in the unpredictable properties of storage-tank liquids. LevelMaster floats can measure oil, water, and emulsion levels up to 25 feet (7.6 m) deep, with a standard relative accuracy of 0.1 inch (2.5 mm) or optional high-precision relative accuracy of 0.05 inch (1.25 mm).
-
product
Standard 0.81 (23.00) - 4.50 (128.00) Battery Probe
CP-059-025
Current Rating (Amps): 10Average Probe Resistance (mOhm): 25Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 57Full Travel (mm): 1.45Recommended Travel (mil): 40Recommended Travel (mm): 1.02Mechanical Life (no of cyles): 100,000Overall Length (mil): 313Overall Length (mm): 7.95
-
product
Gauge Type T Thermocouple Wire
W-TW-30
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
product
PCI Express x4, Gen3 XMC Carrier
TPCE278
The TPCE278 is a standard height PCI Express Revision 3.0 compatible module that provides one slot for a single-width XMC module used to build modular, flexible and cost effective I/O solutions for all kinds of applications like process control, medical systems, telecommunication and traffic control. The TPCE278 is a versatile solution to upgrade well known XMC I/O solutions to the PCI Express signalling standard. The PCI Express x4 link from the host board to the XMC module is enhanced by a PCIe Gen3 Redriver, allowing safe operation of XMC modules on PCIe mainboards.
-
product
New Lead Acid Battery CCA Tester With Printer
Hangzhou Xun Anda Electrical Co., Ltd.
1. Test application: 12V/6V batteries test and 12V/24v Starting /Charging system test.2. Test battery type: regular liquid, AGM battery, GEL battery.3. CCA test range: 40~2000CCA (SAE).4. Voltage test range: 1.5-30V.5. Display SOH (state of health), SOC(state of charge).6. Test for multiple battery standards: SAE, DIN, EN, IEC, CA.JIS7. Graphic LCD display with back light, LCD brightness adjustable.8. Multigle language operation: English, Chinese, Germany, French, Spanish.9. Intergrated thermal printer to print test reports.10. Thermal printer paper roll is 58mm width and 7.5m long.
-
product
RX Family Of 32-bit High Power Efficiency MCUs
RX200
The RX200 Series offers the best mix of low power consumption and improved performance in the RX Family. It delivers max. of 80MHz CPU operation with 32KB to 1MB of embedded flash memory. RX200 Series offers a wide set of peripherals, including USB, CAN, ADC, advanced security, and IEC60730 appliance safety standard support. The RX200 Series is suitable for industrial equipment, home appliances, office equipment, healthcare products, meters, and so on. Some of the RX200 Series products are tuned for motor control solutions, too.
-
product
Fume Hood Monitor
FHM10
Fume hoods are a primary source or protection in laboratories. Face velocity measurements are often used to gauge the performance of a fume hood’s ability to contain and exhaust hazardous chemicals. By accurately measuring face velocity and alarming on unsafe conditions, TSI’s FHM10 Fume Hood Monitors provide a high level of fume hood safety. And, the FHM10 helps users comply with standards and regulations set forth by OSHA, NFPA, ANSI Z9.5, and SEFA, calling for monitors to be installed on fume hoods.
-
product
Hydrogen Frequency & Time Standard
CH1-1006
The hydrogen frequency and time standard Ch1-1006 is designed to generate highly stable, high-frequency, spectrally pure sinusoidal 5, 10, 100 MHz and pulsed 1 Hz signals and for the behavior of time-frequency measurements.
-
product
ACQUA Compact Systems
ACQUA Compact Systems are cost-effective complete solutions for specific measurement tasks. They comprise the compact version of the ACQUA software as well as the corresponding front ends and measurement standards.
-
product
Standard 1.53 (43.00) - 4.00 (113.00) High Performance Lead Free Probe
LFRE-72U-4
Current Rating (Amps): 3Average Probe Resistance (mOhm): 15Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,700Overall Length (mm): 43.18
-
product
VXI Precision PLL Waveform Synthesizer
3152B
The Racal Instruments™ 3152B Waveform Synthesizer combines 250 MS/s waveform generation performance, versatility, and compact size into a single-slot VXIbus format.The 3152B is a greatly improved version of a fi eld-proven instrument ideal for VXI test stimulus generation. It replaces the 3152A which is standard on many military and commercial test platforms
-
product
Remote Displays
HS Series
Load cell / scale remote displays are driven from another digital indicator or amplifier. Often used on bridge cranes and truck scales, or in any situation which the person needing to see the scales displayed weight is too far to see the smaller standard indicators. Many styles, digit sizes, indoor and outdoor models are available.
-
product
Microwave Leakage Tester
TEK500
An easy to use, low cost pass / fail microwave leakage detector suitable for commercial and domestic microwave ovens. It is designed to comply with national standards on permitted exposure levels. The TEK500 includes a self test which simulates a real microwave input to ensure the unit is working correctly at all times.
-
product
FPGA Card
VP680
The VP680 is a high performance VITA 46 (VPX) standard compliant card with advanced digital signal processing capabilities. The design has been targeted for customer-programmable implementations of complex FPGA algorithms for digital signal processing (DSP) applications.
-
product
Barcode Verification Systems
REA ScanCheck 3
The REA ScanCheck 3 is an universal, battery-operated, high-performance barcode verification device which operates in accordance with current standards. The verifications document compliance with quality goals in production and monitoring of barcodes on data storage devices and products of all kinds. The measurement principle is based on a laser scanner optimized for verifications. This makes contact-free measurement, largely independent of handling influences, possible. For mobile use on site, the device operates self-sufficiently, independent of the power network with standard, rechargeable batteries. The operating system and application software support multiple languages.
-
product
MIL-STD-1553 Data Acquisition Module for Ethernet Networks
eDAQ-1553
Avionics Interface Technologies
One or two dual redundant MIL-STD-1553 bus interfaces - Transformer and Direct bus coupling supported - Two 10/100/1000 Mbit/s Ethernet LAN Interfaces - Streams MIL-STD-1553 bus data in standard IRIG 106 Chapter 10 format. - Compatible with 3rd party recorders and telemetry tools - All captured MIL-STD-1553 bus data provided with timestamps - Full error injection & detection capabilities - Works with AIT’s Flight Simulyzer™ GUI Analyzer/Simulator software
-
product
Cup, Concave 90/120°, Standard 0.61 (17.00) - 2.80 (79.00) General Purpose Probe
HPA-0A
Current Rating (Amps): 3Average Probe Resistance (mOhm): 35Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 67Recommended Travel (mm): 1.70Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 635Overall Length (mm): 16.13
-
product
Peeling Tester
BN-3
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3;Inspection standard: JB/T4279.6-2008Used to measure the film adhesion property of enameled round wires with nominal conductor diameter of 1.0mm and below;High-end SCM control is used;Set arbitrarily the number of twist;LED would automatically display the number of twists;Twist counter performs accurate and reliable counting;High-strength steel scraper would complete sample scarping at once, easy to operate and use.
-
product
64 Gbaud High-performance BERT
M8040A
The Keysight M8040A is a highly integrated BERT for physical layer characterization and compliance testing. With support for PAM-4 and NRZ signals and data rates up to 64 Gbaud (corresponds to 128 Gbit/s) it covers all flavors of 200 and 400 GbE standards.
-
product
Tri-Temp Test Handler
JANUS 2800T Tri-Temp Handler
SESSCO Janus 2800T Tri-temp Handler is designed to accommodate small to medium size standard and custom IC packages. Supports high parallelism of up to octal sites and is equipped with dual high-speed input tube loaders and dual auto output tube unloaders for higher throughput up to 28K UPH. With over 500+ I/O and 16 temperature zones available, it has plenty enough resources for the most demanding applications. It can be customized for MEMS applications and high-voltage testing. Powered by a cutting-edge 10 ns/step all-integrated controller and modular programming design.
-
product
Concrete Corrosion Mapping System
15620
Our Concrete Corrosion Mapping System (CCMS) can be used to satisfy the ASTM C-876 standard test method and the kit contains all equipment items that are needed to perform a corrosion survey on virtually all types of reinforced concrete structures, such as bridges, highway slabs and parking garages.
-
product
Standard Voltage 9-Pin D-Type Connector & Cable Accessories
The Standard Voltage 9-Pin D-Type connector is used on PXI switching products to provide a low density connector solution. Connection solutions for modules with High Voltage Rating D-Type connectors are also available.
-
product
Custom Reed Relays from Pickering Electronics
Pickering Electronics manufactures hundreds of model relays. Many of these custom reed relays are minor variations of a standard part, for example, a different test specification or pin configuration. Others are custom designed to meet our customer's particular requirements.
-
product
Cord Guard Flexing Apparatus
CGF-45
Is designed & manufactured to perform the test specified in many standards to determine compliance with safety requirements related to cord guard flexing. It can be used to test cord guards in Electrical Appliances, Portable Power Tools & other similar equipment & is designed to meet the requirements of several international and national standards.
-
product
Standard And Custom Targets
Santa Barbara Infrared manufactures a wide range of targets for visible, and infrared/FLIR electro-optical testing. These targets complement our complete line of Visible and IR test products. Our targets are designed to function with one of SBIR’s target wheels. Utilizing a variety of manufacturing techniques, including conventional machining, photochemical etching, electro-deposition, electrical discharge machining (EDM) and laser cutting. SBIR targets are manufactured to exacting mechanical tolerances. SBIR manufactures all of the targets specified by MIL-STD-1859 and the Tri-Service Guide for thermal imager testing.
-
product
Semi-automatic Single Phase Close Link kWh Meter Test Bench
SY8120
Hong Kong Songyang Industrial Ltd.
The SY8120 new series semi-automatic single phase energy meter test board, designed according to International Standard, is newly developed ideal measuring equipment for energy meters. The equipment can be operated easily through test board button to preset directly all data of meter under test and test process.
-
product
Standard 1.10 (31.18) - 4.80 (136.00) Switch Probe
TSP100-FK180-1
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,990Overall Length (mm): 50.60Switch Point (mil): 59Switch Point (mm): 1.50
-
product
Fixed Attenuator
FAXE
Fixed Attenuators are waveguide components for introduction of some particular attenuation value in to the waveguide network for signal leveling or reflection compensation. The attenuators have two types of design: with resistive plate in the waveguide diagonal plane or using coupling technology. The FAXE 3, 6, 10, 15, 20, 30 dB attenuators are available in waveguide bands from 18 through 225 GHz. The FAXE Fixed Attenuators can be used as laboratory Standards against which other instruments or devices are calibrated in case the parameters of these Fixed Attenuators are stable enough and were measured with appropriate accuracy.
-
product
Nonwovens Run-off Tester
TN130
TESTEX Testing Equipment Systems Ltd.
A piece of standard absorption media is placed under and the specimen, the combined sample are placed in a tilted pad, measuring when a specific amount of artificial urine to flow downward to the combined sample, the liquid penetrate nonwovens and be absorbed by absorption medium. Weigh the standard absorption media before and after test, the performance of fluid loss of nonwoven samples is evaluated according to the change of the weight of the absorption media
-
product
Blackbody System
IR-518/301
Infrared Systems Development Corp.
The IR-518 Radiation Source provides an accurate, stable source of infrared radiation of known flux and spectral distribution. It can be used as a standard radiation source for the calibration of other laboratory sources, detectors, or other infrared devices requiring calibration against a standard.
