Signal Level Meters
detect, measure, and monitor power or the intensity of a signal.
See Also: Level, Liquid Level, Level Transmitters, CATV Signal Level Meters, Satellite Signal Level Meters
- Virginia Panel Corporation
product
Signal, Patchcord, Receiver, 36", TriPaddle, USB 2.0 Wire, to USB Type A Plug (1.5 Amps)
7-104872596-036
Signal, Patchcord, Receiver, 36", TriPaddle, USB 2.0 Wire, to USB Type A Plug (1.5 Amps).
-
product
Signal Level Meter
180 DSP
The 180 DSP is a basic installer meter specifically tailored for installation and troubleshooting. Featuring fast measurements and powerful troubleshooting tools the 180 DSP comes equipped with all the tests an installer needs to measure both Analog and Digital signals and ensure the highest quality installation.
-
product
SDI MASTER
SDI-1
The SDI MASTER is a digital, hand-held, battery operated meter that measures six characteristics of High Definition and Standard Definition digital television signals. Use it for fast and accurate set-up and verification of levels, slope-loss and return loss on any SDI (Serial Digital Interface) Digital Television Signal. This meter is a must have for anybody working with digital TV.
-
product
Surround Meter
A combined level and correlation meter for Surround signals for the 5.1 - Standard. The levels of all six channels as well as the phase correlation between all combinations of two channels are represented, so that defined statements are possible for the mono compatibility of a stereo and a Surround signal, in addition, for the Stereo compatibility of a Dolby Prologic signal or a 5.1-Signals in the Downmix.
-
product
Satellite Signal Level Meter
Super Buddy 29
The Super Buddy 29 satellite meter has all of the great features of the standard Super Buddy satellite meter plus an internal combo 21 volt / 29 volt module to power the new DIRECTV SWM LNBs and the WildBlue / Telesat / Xplornet TRIAs! Be "sure of your bird" with the positive ID feature or use the automatic scan to identify the unknown satellite.
-
product
Portable Hand Held Load Cell Indicator
MODEL SSI
The SSI is a Plug & Play Smart TEDS IEEE 1451.4 compliant portable handheld Load Cell Indicator. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SSI will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SSI can be set up by simple front panel push buttons. The SSI can be scaled to a full 5 digit display from 0 to 99,999 counts to read directly in engineering units such as grams, ounces, pounds, inch pounds, etc. The SSI also has a...show more -
product
Signal Level Meter
SLM-5870
Compact, light-weight, easy to carry With dual-channel measurement display Channel and single frequency mode
-
product
Other CATV Meters
Wuhan Sunma Technology Co., Ltd.
SunmaFiber provide all kinds of CATV meters, such as Signal Level Meter, QAM Analyzer, Spectrum Analyzer, DVB/DVC/DVT Analyzer and other TV testers. also you can find other more equipment in CATV / Broadcasting fileds, such as Three Frequency Points, HFC Return Path Signal Generator, Return Path Signal Generator, Digital RF Signal Generator and so on.
-
product
Signal Level Meter
T1125
Hangzhou Softel Optic Co., Ltd.
The signal level meter, SE828C is able to measure EQ, C/N, V/A and trunk volt in the CATV analog system, the number keys is designed to direct input frequency so that work would be easier. It can measure 2 channels at the same time.
-
product
Analog RF Signal Level Meter
CT-SLM828A
Analog RF signal level meter, measures analog RF signals from channels 2-125, measures carrier to noise, video carrier, audio carrier and line voltage
-
product
Terrestrial Signal Finder
Satlink WS-6905
Jointron(Quanzhou)Industry Co.,Limited
1.Satellite TV Equipments Including satellite receivers, satellite signal level meter, satellite finder(meter), HD DVB-S2 Receivers, DVB-S2 Meter with Spectrum Analzyer(in real time) 2.Terrestrial TV Equipments Inlcuding DVB-T receivers, DVB-T Meter, HD MPEG-4 DVB-T Meter, HD MPEG-4 DVB-T Receiver, SD MPEG-4 DVB-T Receiver 3.Combo Equipment: Including SD MPEG-2 Satellite&Terrestrial Combo Meter, HD MPEG-4 satellite&Terrestrial Combo Meter
-
product
Handheld Signal Level Meter
CT-DLM870D
The CT-DLM870D is a hand held signal level meter capable of reading analog, digital QAM and digital off air signal levels as well as Carrier to Noise, Bit Error Rate (BER), Modulation Error Rate (MER) and tilt.
-
product
CW Test Signal Generators
Applied Instruments CW test signal generators generate CW carriers that are extremely clean and stable. Because of their excellent frequency and amplitude accuracy, they are also great for calibrating signal level meters and spectrum analyzers.
-
product
CAMERA LEVEL METER
SDI-2
The SDI-2 is a low cost pocket size, digital, hand-held, battery operated meter that measures HD (High Definition) video signals. Use it for fast and accurate set-up and verification of levels and slope-loss on any SDI (Serial Digital Interface) signal. This meter is a must-have for anyone working with HD CCTV cameras or any SDI video signals.
-
product
Digital Panel Mount Load Cell Meter
MODEL DPM-3
The DPM-3 is a smart Plug & Play TEDS IEEE 1451.4 compliant Digital Panel Mount Load Cell meter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the DPM-3 will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the DPM-3 can be set up by simple front panel push buttons. The DPM-3 can be scaled to a full 5 digit display from 0 to 99,999 counts to read directly in engineering units such as grams, ounces, pounds, etc. The DPM-3 samples 60 reading...show more -
product
2.4 MHz Level Test Meter
ET91
*Level Meter, for selective and wideband level measurements with auto ranging*Generator, for the generation of measuring voltage for the test of FDM systems*Bridge, for the measurement of input and output parameter*Spectrum Analyser, for the test of output PSD, cross-talk and other interference signals
-
product
Video Level Meter
VLM1
This meter provides a direct reading in volts of peak white and sync levels of a CCTV signal on a 4 digit LCD display. An input impedance switch provides slection between terminated (75Ω) and unterminated (high impedance) input.
-
product
Signal Level Meter
HT828B
Hangzhou Softel Optic Co., Ltd.
The signal level meter, SE828C is able to measure EQ, C/N, V/A and trunk volt in the CATV analog system, the number keys is designed to direct input frequency so that work would be easier. It can measure 2 channels at the same time.
-
product
LED Power Driver ATS
8491
1. DC Electronic Load : Chroma 6310A/6330A Series2. Transducer Unit/Module*1 : Chroma A849101/A849102, A849103, A8491043. Time/Noise Analyzer : Chroma 80611 & 80611N card4. Sytem Controller*2 : Industrial PC5. DC Source: Chroma 62000P Series6. Digital Power Meter : Chroma 66200 Series7. OVP/Short Circuit Tester : Chroma 806128. ON/OFF Controller : Chroma 80613*1 : A849101 transfers UUT output signal to voltage signal, and measure by 84911 LED power driver measurement card (200kHz). The optio...show more -
product
QAM And PCM Analyzers
GAOTek provides a wide range of high performance and inexpensive QAM/PCM analyzers. Quadrature amplitude modulation (QAM) and pulse code modulation (PCM) analyzers are convenient instruments with top to bottom estimations and adaptable setups. Additionally, these devices have integrated functions of analog signal generators/receivers, BERT, signaling generators/receivers, selective level meters, ring generators/ identifications, dialers, DC loop circuits (ICT, OGT), balanced bridges and reflecting bridges into solitary instruments. These analyzers are ideal for installing and maintaining digital and analog networks.
-
product
Digital Signal Generator
Digital Signal Generator*signal frequency:0.1Hz~2MHz, continuously variableave from: square, sine*output attenuator: 0dB,, 20dB, 40dB, 60dB*output level: 20Vp-p in open circuit, not less than 10Vp-p with 50Ω load*rising and falling edge of square not more than 35ns,*sine distortion less than 1%, amplitude –frequency characteristic : ±0.5dB within 100KHz, ±1dB above 1MHz*frequency meter: 10Hz~30MHz*power supply : AC 220V(110V optional)
-
product
Satellite Signal Level Meters
Modular design with field swappable modules providing versatility for different measurement applications, including DBS satellite, VSAT satellite, VHF/UHF off-air, and CATV (QAM and analog).
-
product
SNR Noise Generator
CNG-EbNo
The CNG-EbNo is a fully automated precision signal to noise (AWGN) generator that sets, and maintains a highly accurate ratio between a user supplied carrier and internally generated noise, over a wide range of signal power levels and frequencies. The internal AWGN meter provides repeatable SNR waveforms for accurate signal generation. The instrument gives system, design, and test engineers in the telecommunications industry a single tool to generate precision signal to noise ratios. These signa...show more -
product
Track-Signal Test Meter
Model TRSIG-1
Aplab Track-Signal Test Meter incorporates Digital Signal Processing based design to provide high accuracy and stability. It is designed for level measurement of selected frequencies. It also provides functionality of AC and DC voltage measurements.The purpose of Track-Signal Test Meter is to make adjustments, control measurements and inspections on both audio frequency track circuits of types FTGS 46, FTGS 917 and also for TI21M type track circuits (now known as BI track 300) for the measuremen...show more -
product
Signa; Generator
MAG-203AD
Features:*Signal frequency:0 .1Hz-2Mhz, continuously variable*Wave form: square,sine*Output attenuator:0dB, 20dB, 40dB,60dB*Output level: 20Vp-p in open circuit, not less than 10Vp-p with 50Ω load*Rising and falling edge of square not more than 35ns*Sine distortion less than 1%,amplitude -frequency characterstic:±0.3dB within 100khz, ±1dB above 1Mhz*Frequency meter: 10Hz-30Mhz*Power supply : AC 220V
-
product
Mobile sound Level Meter
SoundMeter
SoundMeter turns your iOS device into a handheld sound level meter (SLM) with support for exponential-time-weighted sound level (Lp) and equivalent sound level (Leq) measurements with various time and frequency weightings. The built-in signal generator tool can be used for generating calibration test tones, noise, chirps, or other periodic signals. SoundMeter also offers additional tools via in-app purchase, including a Noise Dosimeter and a whole or 1/3-octave real-time analyzer.
-
product
Environmental (Radiation) Monitoring System
Hawk® EMS
The Hawk® EMS is a wall or tripod-mounted radiation monitoring and alarm system designed for use with the Hawk® Radius dual sensor radiation probe. Each EMS System comes with a Hawk Radius Probe. The system is extremely energy efficient and can run for weeks on an internal 9 volt back-up battery if power fails. It is well suited for operating on a small solar panel, which is an optional accessory. The Hawk® EMS features two displays that show the radiation levels measured by each of the pro...show more -
product
Digiair PRO
Frequency range of 45-860MHz.• The meter to use for easy Digital terrestial installations.• Very sensitive, easy to maximize weak and strong signals.• Signal level reads out in dBuV.• Presents one channel readout with high resolution or six channels.simultaneously or the complete spectrum.• Built in beeper (pitch tone) and maxhold function.• Aerial power output, 0, 5 and 12V.• Built in, rechargeable battery.• Power supply and car-charger enclosed.• Carrying-case enclosed.• Small and handy design.• Made in Sweden.
-
product
Function Generators
Respective dual channels function/arbitrary waveform generator. Sine wave output up to 160MHz, full-band resolution of 1μHz. Pulse waveform up to 50MHz (or 40MHz), adjustable time of rising, falling and duty ratio. Sampling rate of 500MSa/s and vertical resolution of 16bit. 6-bit high-precision frequency meter compatible with TTL level signal. Arbitrary wave storage of 8~32M points, 7GB non-volatile waveform storage. Multi modulation function::AM,FM,PM, ASK,FSK,PSK, BPSK, QPSK,OSK,PWM, QAM, SUM ...show more -
product
Audio Volume Meter
AVM
This is a true RMS audio storage meter used to measure audio volume levels of live program material. Use it to periodically survey your system for high or low audio levels to prevent complaints about loud or un-even audio programming. You can use this meter to quickly locate and verify any objectionable signals levels and bring them into compliance.
-
product
Loss Testing
Count on Tempo Communications Optical Power Meters to test and maintain your fiber optic networks. Use to accurately ensure that signals are being transmitted at the correct power levels in your fiber network.