Showing results: 4591 - 4605 of 8242 items found.
-
EM-6851 | 2 GHz – 18 GHz -
Electro-Metrics Corp.
The EM-6851 Omni-Directional Wideband Antenna is capable of operating as either a transmitting or receiving antenna over the 2 to 18 GHz frequency range. This antenna provides a 45% size reduction when compared to similarly performing models. The antenna is enclosed in a weather resistant radome. The length of the support rod allows a microwave amplifier to be connected directly to the output connector, reducing the potential signal loss compared to an amplifier connected at a more distant point.
-
MegaPhase, llc
MegaPhase now offers custom rack-mounted components for telecom testing. Pictured is a rack that includes twelve 6-way power dividers with quick-connect HPQN connectors from 678 to 2700 MHz. Each divider includes a monitor port for quick signal checks. The monitor port coupling values are typically -3.0/+2.0dB. These low loss dividers feature a minimum 17dB of isolation, phase balance of +/- 10 degrees, and amplitude balance of +/- 0.5dB.
-
SFT357x -
Hangzhou Softel Optic Co., Ltd.
SFT357X IRD is DEXIN’s new design which integrates demodulation (DVB-C, T/T2, S/S2 optional), de-scrambler in one case to convert RF signals into TS output after re-mux. It is a 1-U case which supports 4 tuner inputs. The 4 CAMs/CIs accompanied can descramble the programs input from encrypted RF, ASI and IP. The CAM requires NO unsightly external power cords, cables, or additional remote control device.
-
626 -
Sensoray Co., Inc
6 versatile 24-bit counters for encoders/timers with interrupt generation Fail-safe Digital I/O E-stop Relay Battery backup of counters Four 14-bit D/A outputs, 20 Khz update rate Sixteen 16-bit differential A/D inputs, 15 kHz rate Watchdog timer may be used to reset PCI bus 48 bi-directional digital signals for solid state relay boards, 40 with edge detection and interrupts
-
V862 -
CAEN S.p.A.
The Model V862 is a 1-unit wide VME 6U module housing 32 Charge-to-Digital Conversion channels with current integrating negative inputs. Each channel has an independent gate input (GATE i) logically ANDed with a COMMON GATE input; the input charge on the i-th channel is converted to a voltage level by a QAC (Charge to Amplitude Conversion) section when both the GATE i and COMMON GATE signal are active.
-
QProny -
QWED Sp. z o.o.
In order to assist the users of QW-3D in the analysis of high Q structures, a special software module QProny, co-authored by Prof. M. Mrozowski was developed. QProny uses one of the most robust signal processing techniques known as the Generalised Pencil of Function Method (GPOF) and employs unique and innovative methods for automatic selection of the most important parameters such as:• the number of initial samples to be skipped• the number of samples required for model construction• the model order
-
60-803-102 -
Pickering Interfaces Ltd.
Our 60-803-102 is a 2 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 18GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
60-803-305 -
Pickering Interfaces Ltd.
Our 60-803-305 is a 5 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
60-803-711 -
Pickering Interfaces Ltd.
Our 60-803-711 is a 11 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
60-802-402 -
Pickering Interfaces Ltd.
The 60-802-402 is a 4-channel, 2-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
60-801-215 -
Pickering Interfaces Ltd.
The 60-801-215 is a 6-channel, 15-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
60-803-704 -
Pickering Interfaces Ltd.
Our 60-803-704 is a 4 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
60-803-103 -
Pickering Interfaces Ltd.
Our 60-803-103 is a 3 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 18GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
60-802-214 -
Pickering Interfaces Ltd.
The 60-802-214 is a 4-channel, 14-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
60-803-309 -
Pickering Interfaces Ltd.
Our 60-803-309 is a 9 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.