Showing product results. 301 - 315 of 3227 products found.
-
Balluff GmbH
These pressure transmitters are compact and robust. They can be used for a pressure range of 0 to 600 bar and for gaseous, liquid and viscous media. They are equipped with IO-Link, analog output and switch point (PNP/NPN). Process connection: G1/4", G1/2", NPT1/4", R1/4". Housing and process connection in stainless steel. IP67 or IP69K. Customer-specific modifications upon request.
-
ATAL
Differential pressure for clean gasesAvailable with or without display. Various output signals possiblemeasuring sets
-
Dytran Instruments, Inc.
100 mV/psi, 50 psi range, TNC axial connector, 1/8-27 mounting thread, 43 grams, +275°F (+135°C) operation, IEPE
-
McLAREN Applied Technologies
The output voltage of this sensor changes with absolute pressure. An internal amplifier creates a single-ended, amplified output in the 0 to 5 Volt range, so the sensor can be connected directly to most control units. The body and diaphragm are impervious to chemical attack by standard motorsport fluids.
-
ESPP-MIT1 Sensor - ES Systems
ES Systems has developed a series of strain gauge pressure transmitters featuring very good accuracy at a low cost. Each module is based on an all-welded hermetically sealed structure in a single stainless-steel piece. The ESPP-MIT1 is a medium isolated pressure sensor suitable for gas or fluid pressure measurements in harsh industrial or HVAC environments.
-
ESCP-MIT1 Transmitter - ES Systems
The ESCP-MIT1 of capacitive pressure sensor dies integrated into the medium isolated pressure systems provide state-of-the-art accuracy and resolution, excellent long-term stability combined with very good repeatability and hysteresis. The total overall error, including thermal offsets, is lower than ±0.25% FS.
-
ESCP-BMS1 Sensor - ES Systems
ESCP-BMS1 is an absolute, gauge or differential pressure sensor of ultra-high resolution with analog (0-3,3V), PWM, SPI or I2C interface. The output is fully calibrated, and temperature compensated based on the internal temperature sensor and the factory calibration coefficients which are stored in the embedded memory. The sensor is ready to be installed directly to the end system without further processing with medical, HVAC, industrial, commercial & automotive applications. The total error including repeatability, hysteresis, non-linearity, thermal offset and calibration error between 0°C and 60°C is better than 0.25% FS.
-
Anton Paar GmbH
To achieve the highest product quality, to minimize production and maintenance costs, and to react immediately to deviations in the production line, the continuous control and analysis of the production process are mandatory. The improved visibility of all process steps goes hand in hand with increased product quality. Therefore, the best process instrumentation is required.
-
Festo Corporation
Voltage 0...250V DC, 230 V AC Cable length 0.3, 2.5, 5, 7.5, 0.2...10 m Plug connection M8, M12 / female thread M5 Electrical Via reed contact Contactless PNP, NPN Pneumatic.
-
Omron Industrial Automation
The high quality and the long-life design of them extended sensing distance provide the best value performance ratio for standard applications.
-
E2E-Next - Omron Corporation
Four shielded sizes from M8 to M30, as well as an unshielded M30 format. For a shielded M12 version, the sensing distance has increased from 3mm to 7mm, while for an unshielded M30 version, the distance has been extended from 20mm to 40mm.
-
-
-
ifm efector, inc.
*2 in 1: speed sensor and evaluation in one compact housing*Space-saving design*Inductive or magnetic sensor principle*Flexible combination of housings, connections and output signals
-
Magnetometers - Magnicon GmbH
The famous cart-wheel design multiloop dc SQUID magnetometers, designed and fabricated by PTB-Berlin are available in three different sensitivities.
