Filter Results By:

Products

Applications

Manufacturers

Sensors

detect a physical event then translate to a representative analog signal.

See Also: Measurement, Detectors, Meters, Transducers


Showing product results. 2866 - 2880 of 3227 products found.

  • Galvanic Isolation Amplifier

    X005 Series - Positek Limited

    The X005 Galvanic Isolation Amplifier provides a regulated and resistively limited +5V dc power supply required by the sensors, it can be connected in three or five wire modes. Used in five wire mode positive and negative sense inputs enable the X005 to dynamically adjust the sensor supply thus ensuring the correct voltage across the sensor. Connected in this way the X005 can compensate for 15 conductor resistance. The sense terminals are linked internally so the end user can use the X005 in three wire or five wire mode without the need to fit or remove external links.

  • GMSL3

    Framos Technologies d.o.o.

    FRAMOS is the first company in the market to integrate Analog Devices’s new GMSL3 technology into an embedded vision environment. GMSL3 can transmit high frame rates (4K, 90 fps) as far as 14 meters with unprecedented efficiency. This interface is well suited for applications where the MIPI CSI-2 (D-PHY) length restrictions are not sufficient, while at the same time, a highly durable cable with low power consumption and low cost are essential. Camera developers can use the flexible FRAMOS Sensor Module Ecosystem to validate a variety of image sensors in the lab and in the field while taking advantage of the interface’s features.

  • Hazardous Flow Testing

    National Technical Systems

    NTS performs pressure, flow, and combined testing programs on flexlines, piping, storage vessels and measurement and control systems utilizing the actual fluids that these systems will use in service. NTS has the ability to test anything from heat exchangers, meters, sensors, valves and filters to high pressure storage tanks (such as those on launch vehicles and satellites) and rocket test stand fuel systems utilizing any of the following: liquid fuels, gasoline, JP1, hypergols, hydrogen, oxygen, steam, diesel, nitrogen, Skydrol, kerosene, cryogenics, ammonia, hydrogen peroxide and other substances.

  • High Speed Data Logger

    9330 - Interface Inc.

    The Model 9330 displays 24-bit resolution and has an impressive 3750Hz update rate. Incorporating peak and valley capture, it can store up to 6 sensor calibrations and measurements from load cells or torque transducers can be logged at 1000Hz to a standard SD card. This data can then be downloaded to a PC via the built-in USB port and Windows compatible software for off-site analysis. Adding further versatility, the rechargeable battery can power up to 4 x 350 ohm sensors, but also offers up to 300 hours stand by time and up to 20 hours continue use.

  • Infrared Moisture Analyzer

    LD-LIMA-A10 - Labodam

    Infrared Moisture AnalyzerLD-LIMA-A10is an online, fast, continuous measurement and non-contact measurement device with measurement distance range of 20 to 40 cm. It provides automated control and 4 to 20 mA current signal. This IR Moisture Analyzer emits different wavelengths of infrared light (4, 6, 8, 10 beam) to calculate the moisture content of the measured object. Designed with long-life high-speed brushless motor, imported high response infrared sensors, information processing chip FPGA + DSP + ARM9 combination, to attain real time data, improved stability and precision.

  • Long Range Thermal Imaging Surveillance System

    Ranger HRC - Teledyne FLIR

    The Ranger HRC is a high-resolution mid-wave thermal imaging system built around a large format 640x480 array and a choice of powerful continuous-zoom telescopes. While the Ranger HRC is available in its standalone, environmentally hardened enclosure, it can also include and optional high-magnification CCD-TV camera, laser rangefinder, digital magnetic compass and an integrated, gyro-stabilized, pan/tilt mechanism that provides precise target geo-location capability. Operators can field Ranger HRC as a portable stand-alone system, or integrate it into a network of fixed-site sensors via its suite of plug-and-play interface options.

  • Low Noise Accelerometer Cables & Coaxial Sensor Cables

    Kemo

    Our cable assembly team in the UK produce the highest quality cable assemblies for use with a wide range of sensing and measurement applications. By making the cable assemblies in our own factory we are able to ensure the quality of every connection and every assembly, each cable is fully tested and its capacitance checked. Due to our experience in signal conditioning we understand the critical elements to quality signal analysis, this includes the correct cable. This is particularly true for accelerometer cables and sensors cables which can introduce significant noise issues if not used correctly.

  • Magmeter Flow Sensor

    2551 - Georg Fischer Signet

    The Signet 2551 Magmeter is an insertion-style magnetic flow sensor that features no moving parts. The patented* sensor design is available in corrosion-resistant materials to provide long-term reliability with minimal maintenance costs. Material options include PP with stainless steel, PVDF with Hastelloy-C, or PVDF with Titanium. Utilizing the comprehensive line of Signet installation fittings, sensor alignment and insertion depth is automatic. These versatile, simple-to-install sensors deliver accurate flow measurement over a wide dynamic range in pipe sizes ranging from DN15 to DN900 ( to 36 in.), satisfying the requirements of many diverse applications.

  • Miniature

    Columbia Research Laboratories

    This group is made up of the 6000 and 7000 Series Accelerometers. The 6000 Series offers detachable cables and connector assemblies, a special inverted seismic element for mechanical isolation and other features normally available only on standard size sensors. The 7000 Series are true "shear-mode" design accelerometers which offer performance characteristics and accuracies normally only available with standard size accelerometers. High temperature models of these series are available and will operate to +500°F. For best performance use with Columbia Model 4601 Charge Amplifier or Model 5810 Inline Charge Converter.

  • Multispectral Cameras

    PixelCam - PIXELTEQ

    PixelCam™ multispectral cameras provide live imaging of 3-9 spectral bands at video rates. Simultaneous multi-channel “snapshot” acquisition delivers rich, real-time data without scene change or pixel shift. Custom dichroic filter arrays are integrated into the focal plane array at wafer-level to create robust linear and area sensors that extract high-contrast spectral information at specific visible and infrared wavelengths. This breakthrough technology enables easy integration into handheld, mobile and aerial cameras – all with the same frame rate, size, weight, and power consumption as monochrome cameras.

  • PC104 Switches

    Curtiss-Wright Defense Solutions

    Our PC104 switches provide systems integrators with a fast and powerful way to interconnect chassis, cards, and CPUs through switched Fast and Gigabit Ethernet links. These PC/104 Ethernet switches, optimized for size, weight, and power (SWaP)-sensitive embedded military and civilian computer network systems applications, enable reliable local area network (LAN) switching in extended operating temperature ranges and extreme shock/vibration environments. Ideal for connecting computers, cameras, sensors, and command and control equipment, these cards are typically deployed in manned and unmanned system platforms.

  • Piezoelectric Testing

    Radiant Technologies, Inc.

    Radiant Technologies, Inc. specializes in the measurement of electrical and piezoelectric properties of non-linear materials.   The Piezoelectric Task captures a sample's displacement  as a function of voltage profile along with the sample's polarization response.  An external displacement measurement instrument must be attached to a Radiant Precision Test System to make this measurement.  All of the Radiant testers are equipped with a high-impedance voltage input to capture the output of a displacement sensor. Every Vision measurement task will collect data from that sensor input simultaneously with the measurement being executed. Radiant's test systems work easily with displacement sensors which include:

  • Pitot / Static Tester for Laboratories and Workshops

    ADSE 741 - ATEQ Aviation

    The ADSE 741 is a complete high performance three channel Ps, Pt and AoA stand-alone test bench specially designed to be used in the workshop or in the laboratory to test and calibrate all air data equipment such as altimeters, vertical speed indicators, air speed indicators, pneumatic AoA (Angle of Attack) indicators, MACH-meter, air data computers, specific probes and sensors.The high precision embedded sensors enable the ADSE 741 to be used as a pressure standard.The user interface is programmed underWindows and Labview, with a data base managed in a spreadsheet for easy evaluation, management, statistics and presentation.

  • Portable Dew Point Monitor

    1500 - Edgetech Instruments

    The Model 1500 is a self contained system; not only is there no field assembly required, there’s no need to carry around a myriad of individual components such as control boxes, sensors, cables, pumps, and power cords. Simply attach the sample line, adjust the flow (with the integral flow meter) and turn on the power. Within minutes you’ll be collecting field dew point data with the same chilled mirror accuracy of a lab standard hygrometer. And with a nominal battery life of 12 hours, you will be able to collect for the entire shift or spot check your processes for several days.

  • PXI BRIC4 FIBO Matrix Dual 124x4 2pin Brkout

    40-592A-014 - Pickering Interfaces Ltd.

    The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines. Typical applications are in automotive and aerospace industries which involve safety or mission critical systems that have to behave predictably when cabling or sensor faults occur.

Get Help