- Pickering Interfaces Inc.
product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 1.02k Ohm
50-294-021
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Low Voltage Burn-in and Test System
Max 450
For burning-in and testing DUTs such as microprocessors, DSPs and logic devices, which require low voltage. Output monitoring gives functional test results for every device during burn-in
-
product
PD free AC Hipot Test Set
FPA Series
FPA Series test sets perform field or factory testing on larger electrical apparatus, including motors & generators, switchgear, bushings, bus duct, etc. This series offers the higher kVA ratings needed (0-6/12 kV AC @ 6 kVA), but is still packaged for portability.
-
product
Pil Dielectric Test Sets
DTS Series
The DTS Series provides repeatable and accurate measurements of the breakdown voltage of insulating oils used in electrical equipment. The DTS-60D & DTS-100D offer 60 kV AC and 100 kV AC output respectively. They include three user-selectable, automatic voltage rates-of-rise, and automatic voltage shutdown with the meter indicating the flashover voltage. Various test cells are available.
-
product
Insulation Resistance Testers
UEi Test & Measurement Instruments
Measures the total resistance between any two points separated by electrical insulation.
-
product
High Voltage Probes
High voltage measurements have a variety of different requirements, and our PVM series and VD series probes are designed for most of these requirements. The PVM probes are designed for wide bandwidth and ease of portability where a variety of measurements must be made. The VD series probes are designed for use at higher voltage ranges, and where physical stability is required.
-
product
Battery Internal Resistance Tester
HDGC-3915
HD Power Test Equipment Co.ltd
Battery Internal Resistance Tester is designed using the advanced AC discharge measurement method to test accurately voltage and resistance of battery. It is strictly designed to evaluate battery performance, state and life-time, which maintain all stationary power systems including Uninterruptible Power System. Battery Internal Resistance Tester can proceed the measurement in a group and in a single section of battery. With accurate testing of resistance and voltage, it gives an indication of ...show more -
product
Insulation Resistance Tester 600V AC/DC
IRT803
UEi Test & Measurement Instruments
The IRT803 Digital Insulation Resistance Tester has a 600V AC/DC measurement capability and auto ranging. It features a backlit display that shows test function and measured value. And is backed by a 1-Year limited warranty.
-
product
Custom Test Fixtures
Cortek Test Solution’s design capabilities range from very basic to extremely sophisticated solutions. Developing custom test fixtures demands more engineering time as well as an in-depth knowledge of mechanical design, pcb test methods paired with precision machining. Our experienced engineers will evaluate your requirement and design innovative mechanical test fixtures to meet your application needs in both the R & D and production environments.
-
product
RF Shielded Test Enclosure, I/O Intensive Device Tests
JRE 1720
Like its other brothers in the JRE test line, it features rugged welded aluminum construction with superb RF shielding effectiveness. Long life door gasket material along with double edge engagement not only provides solid RF shielding, but smooth trouble-free operation over its lifespan. A JRE exclusive, our triple door locking mechanism allows easy single handle door operation. Ventilation is standard with our JRE exclusive honeycomb style vents in enclosure rear and door.
-
product
Mixed Signal Test Systems
MTS1010i
The MTS-1010i is a more economical version of the MTS-2010i & MTS-1020i testers. It has a reduced platform size and reduced power supplies. Like the other testers in the MTS family it is a highly cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process.
-
product
Ground Resistance
Provide accurate and reliable measurements of both ground resistance and soil resistivity for installation and troubleshooting.
-
product
Leak Test Instrumentation
At Cincinnati Test Systems (CTS), we are dedicated to providing our customers with superior quality leak testing systems. With access to advanced designs, features, and test algorithms in our leak test devices, we promise a fast and reliable leak test product that will also provide repeatable results for air leakage testing, gas leakage testing, or any other leak where reliable testing equipment is needed. Browse our family of products to learn more on how our standard and custom built systems can meet your needs:
-
product
Mixed Signal Test Systems
MTS2010i
The MTS-2010i are a cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process.
-
product
PD-Free High Voltage Test Transformer
Wuhan Sangao Electrical Test Installations Limit Co.
PD-free HV Testing Transformer is a high-end testing transformer which firstly marketed in China by our company. The high-light characteristic of the equipment reflects the smallness in size, lighter in weight clean ,oil-free,unnecessary static of field investigation ,longer working life without maintenance and slightness in non-partial-discharge. It is used for the insulators' voltage-resistance testing.
-
product
System Level Test and Burn-in Solutions
System Level Test (SLT) is a paradigm shift from traditional structural and functional testing. The device is tested in a complete, integrated system to evaluate its compliance against specified requirements. The system approach allows for higher and more cost-effective test coverage especially for multi-function and non-deterministic devices. It also brings new integration and test challenges like: ..Designing test fixtures on Burn-in Boards with system components ...
-
product
100kVA PD-Free High Voltage Test Transformer
Wuhan Sangao Electrical Test Installations Limit Co.
PD-free HV Testing Transformer is a high-end testing transformer which firstly marketed in China by our company. The high-light characteristic of the equipment reflects the smallness in size, lighter in weight clean ,oil-free,unnecessary static of field investigation ,longer working life without maintenance and slightness in non-partial-discharge. It is used for the insulators' voltage-resistance testing .
-
product
Conventional Power Supply Design with Simple Analog Controls
VLF Series
VLF hipots perform voltage withstand tests and provide the voltage source for diagnostic cable testing. There is no better method for verifying the AC integrity of a cable than applying VLF AC voltage. Tan delta and partial discharge measurement accessories are frequently purchased along with VLF equipment to extend their capabilities.
-
product
Threaded Probes Designed for Connector and Harness Test
Equip-Test Threaded Probes Designed for Connector and Harness Test
-
product
Specialty Probes
Upgraded "bare" versions of our probes for space-saving installation into oil (or SF6) tanks are now available. These probes are similar to the VD series probes with somewhat lower accuracy at a somewhat lower cost. When installing these probes some information about the surrounding areas is required. The length of a VD-120 bare probe (120 kV) is 0.35 m. These units are threaded and can therefore be stacked into higher voltage units. The VD-60 and VD-120 are offered at 60 kV and 120 kV respectively. The bare probes are now available for use in air, but only at 60 and 1120 kV sizes.
-
product
Cable Diagnostic Tools
For non-destructive diagnostic testing to determine the quality of a cable’s insulation with minimal risk of failure, HVI recommends tan delta and partial discharge testing for valuable diagnostic data about cable insulation integrity. Both use a VLF source to perform elevated voltage, off-line testing. Tan delta testing measures insulation health, while PD identifies specific problem areas and assesses their severity.
-
product
Test Fixture Kits
More then ten years of experience in special, customized engineering and manufacturing brought us to the highest level of creating reliable, flexible and robust Test Fixtures. Currently our HQ is located in Vecsés, Hungary together with our R&D. Equip Group has Test Fixture Kit manufacturing plant in Serbia, focusing on supplying competitive, high – quality and high – volume products for the global market.With more then 180 employees, Equip – Test is able to offer our customers turnkey solut...show more -
product
High Voltage Testers
HV Test, which is also known as Hipot Test – short form of high potential – is used to test the insulation quality of the auxiliary circuit of circuit breakers. The HV Test is useful in finding damaged insulation, stray conductive materials around the conductors, and problems due to terminal spacing and tolerance errors in cables.
-
product
Voltage Probes
An oscilloscope is only as good as its probes. Our range includes high voltage, differential, active, low capacitance, and passive types, with ranges to 30kV and frequency bandwidths to 5 GHz.
-
product
Modular Test System
A modular test system, RTS (real time scanner) provides instant test results with minimal interface cables to check wiring during installation.It tests wire harnesses in real time using our micro switching technology, reducing the need for high cost interface cables by around 90%. an innovative best-in-class solution for FAL testing, RTS also offers many benefits for wire harness and sub-assembly manufacturers.
-
product
Winding Resistance Test
20A DC booster
The 20A DC STCS booster allows to perform resistance tests on a PT with a current up to 20 A DC. The option is used together with STS 5000 and STS 4000 and must be connected to STCS module.
-
product
In‐Circuit Test Fixtures
Test Head Engineering designs and builds high‐quality In‐Circuit Test (ICT) Fixtures for HP / Agilent / KeySight Technologies 3070 board testers. We partner with In Circuit Test Engineering, Inc. to provide turn-key 3070 ICT solutions - both fixture and programming.
-
product
MANIA TEST PROBE
SERIES 76
ElectricalMAXIMUM CURRENT: 3 amps continuousat working travel, non - inductiveRESISTANCE: At 35 mA test current,50 mOHMS meanMaterial and FinishesPLUNGER: Heat treated berylliumcopper, FINISH: -2E / -2P Hard nickel plated-2D / -2E138 24 Kt gold plated,BARREL: Phosphor bronze, nickel platedSPRING: Stainless steel, silver platedPIN: Music wire, hard nickel plated
-
product
Vacuum Leak Test Systems
Vacuum leak testing is the principal leak test method for testing parts that could have leakage from an external source into their housings and casings. Parts like underwater sensors or housings, outdoor electrical housings, sealed components, and components associated with vacuum sources are all prime candidates for vacuum leak testing. Operation of instruments that supply vacuum to test parts instead of pressure works in a similar, yet essentially opposite, manner as pressure decay testing.