Showing results: 751 - 765 of 1178 items found.
-
MS-700 Series -
EKO Instruments Co., Ltd.
Since their introduction, they were widely used as reference instruments for outdoors spectral irradiance measurements in the fields of Photovoltaic and Meteorological research. In 2001 the MS-700/701 was successfully introduced and adopted by researchers. Since then, the MS series expanded, with sophisticated instruments like MS-711 and MS-712 which cover a wide spectral range for VIS-NIR-IR applications. The MS-series now covers a spectral range from 300nm up to 1700 nm. All spectroradiometers benefit from an advanced spectrometer which is temperature controlled at a fixed temperature to maximise performance in a wide operating temperature range. During the years we proved that long term stability was one of the success factors of the MS-series spectroradiometers.
-
TE0720 -
Sundance Multiprocessor Technology Ltd.
TE0720s are industrial-grade SoC modules integrating a Xilinx Zynq Z020 SoC, a gigabit Ethernet transceiver (physical layer), 8 Gbit (1 Gbyte) DDR3 SDRAM with 32-bit width, 32 Mbyte Flash memory for configuration and operation, and powerful switch-mode power supplies for all on-board voltages. A large number of configurable I/Os is provided via rugged high-speed stacking strips. All modules in 5 x 4 cm form factor are fully mechanically and largely electrically compatible among them. All this on a tiny footprint, smaller than a credit card, at the most competitive price. A free and open embedded development suite with reference designs is included.
-
Zachtek
A serial controllable synthesizer that will output any frequency between 33MHz to 4.4GHz. Arduino Pro Mini + ADF4351. It's a frequency generator that you control using serial commands. The synth has a built-in pre-programmed Arduino Pro Mini that runs a commands parser so you can set any frequency simply by sending is over the serial port. It can be run on voltages from 3,3V to 5V and takes about 140mA of current. There are two complimentary 50 ohms outputs that give out 0dBm. The output is pretty flat over the entire frequency range. It has a stability of 2.5ppm (parts per million) or better when using the built-in TCXO 10MHz reference.
-
ADF4356 -
Analog Devices Inc.
The ADF4356 allows implementation of fractional-N or integer-N phase-locked loop (PLL) frequency synthesizers when used with an external loop filter and an external reference frequency. A series of frequency dividers at another frequency output permits operation from 53.125 MHz to 6800 MHz. The ADF4356 has an integrated VCO with a fundamental output frequency ranging from 3400 MHz to 6800 MHz. In addition, the VCO frequency is connected to divide by 1, 2, 4, 8, 16, 32, or 64 circuits that allow the user to generate RF output frequencies as low as 53.125 MHz. For applications that require isolation, the RF output stage can be muted. The mute function is both pin- and software-controllable.
-
J2190A -
PICOTEST Corp.
The J2190A active filter presents a high impedance (approximately 150kOhms) minimizing the loading of the circuit being tested. The output impedance is 50 Ohms allowing low noise coaxial connections to all typical test equipment. The 0.1Hz-10Hz noise band is common for opamp measurements, voltage regulators and voltage references. Many application notes offer schematics of such a filter for test purposes. An engineer’s time is much too valuable to be spent building test equipment. We have created a 4th order high pass and 4th order low pass filter with an optimally flat response and 0dB gain. Additional filters can be cascaded for even sharper cutoff.
-
Wafer Series -
Park Systems Corp.
Park's Smart ADR provides fully automated defect review and identification, enabling a critical inline process to classify defect types and source their origin through high resolution 3D imaging.Designed specifically for the semiconductor industry, Smart ADR is the most advanced defect review solution available, featuring automatic target positioning without the need for labor intensive reference marks that often damage the sample. The Smart ADR process improves productivity by up to 1,000% compared to traditional defect review methods. Additionally, the new ADR capability offers up to 20x longer tip life thanks to Park's groundbreaking True Non-Contact™ Mode AFM technology.
-
EGX-MXM-AD -
ADLINK Technology Inc.
The EGX-MXM-AD is an PCIe adapter supporting ADLINK NVIDIA® Quadro® MXM 3.1 Type A, Type B, and Type B+ GPU modules for quick validation and early development purposes on your AI applications. The following modules are supported: EGX-MXM-P1000, EGX-MXM-P2000, EGX-MXM-T1000, EGX-MXM-RTX3000, and EGX-MXM-RTX5000. A reference thermal solution is available.
-
Compact Instruments
Electronic Stethoscope Standard Headphones are designed to help locate the source of excess bearing and machine noise easily at low cost, it is an ideal easy to use listening device for mechanically generated noise in all types of applications, the 3.5mm jack socket tape output can also be fed into an audio tape recorder to store the data for either further analysis or as a reference for future comparison.
-
MM14 -
D.Marchiori s.r.l.
The MM14 is a digital technology pressure standard calibrator. It consists of a variety of components combined to allow ease of operation for the verification of pressure based UUTs (unit under test) such as Air Data Test Sets.The MM14 utilises a very accurate dual pressure transfer standard generator, a reference Primary Standard dead-weight and PC based operating system for automatic verification of the U.U.T.
-
C.A 762 -
Chauvin Arnoux Metrix
The CA 762 Voltage Absence Tester is an essential tool for any electrician to check that no voltage is present before working on an electrical installation connected to the network. It complies with IEC 61243-3 Edition 3 and can be used to work on any indoor or outdoor 600 V CAT IV installation. To fulfil the requirements of the standards and legislation in certain countries, there are 2 references, with or without IP2X accessories.
-
SC6 -
North Atlantic Industries
Serial Communication Module SC6 provides up to 4 high-speed, programmable RS-232/422/485, individually non-isolated communication channels. Each channel is programmable for either RS-422/485 (differential, DF) or RS-232 (single ended, SE) hardware level interfaces. Individual channel non-isolated returns are available as part of the channel user interface signal set (for SE or SYS-GND reference).
-
SC5 -
North Atlantic Industries
Serial Communication Module SC5 provides up to 4 high-speed, programmable RS-232/422/485, individually isolated communication channels. Each channel is programmable for either RS-422/485 (differential, DF) or RS-232 (single ended, SE) hardware level interfaces. Individual channel isolated returns are available as part of the channel user interface signal set (for SE or ISO-GND reference).
-
C.A 742 -
Chauvin Arnoux Metrix
The C.A 742 Voltage Absence Tester is an essential tool for any electrician to check that no voltage is present before working on an electrical installation connected to the network. It complies with IEC 61243-3 Edition 3 and can be used to work on any indoor or outdoor 600 V CAT IV installation. To fulfil the requirements of the standards and legislation in certain countries, there are 2 references, with or without IP2X accessories.
-
U9391M -
Keysight Technologies
U9391M comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
FMC160 -
Abaco Systems Inc
The FMC160 provides one 12-bit A/D channel at 3.6Gsps and one 14-bit D/A channel at 5.7Gsps (2.85Gsps direct RF synthesis) clocked by either an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition, a trigger input for customized sampling control is available to users. It is mechanically and electrically compliant with the FMC standard (ANSI/VITA 57.1).
