Receivers
Equipment that is the sink or terminator of any signal on a transmission medium. (atis.org)
See Also: ITA
-
product
Compact Receiver
UCR401
The UCR401 is a high performance compact UHF wireless microphone receiver for mobile applications such as ENG and film production. The compact size, battery and external power and rugged attached antennas are ideal for video camera mounted use. Unique DSP algorithms in the design provide full compatibility with all Lectrosonics 400 Series Digital Hybrid Wireless™ transmitters and variety of analog transmitters from Lectrosonics and some other manufacturers. Power is provided by two AA batteries, typically NiMH rechargeable types, or external DC supplied via a jack on the rear panel.
-
product
Shield Level / Pathloss Equipment
PathTrax
Identical in form factor to the PAMS and PAMS-C, PathTrax provides an optimum solution for site surveys. Once the receiver is calibrated with the transmitter, the receiver measures path loss directly. PathTrax systems are available to cover several frequency bands each 75MHz wide, centered on 838 MHz, 860 MHz and 915 MHz. A PathTrax centered at 500MHz, covering 25MHz of bandwidth is also available.
-
-
product
Module (Venue 2)
VRT2
Up to six VRT2 modules may be installed per each 1RU Venue 2 receiver frame. Each module supports up to 3072 tunable frequencies across a 75 MHz range (three standard Lectrosonics blocks), matching the tuning ranges of SSM, LT and LMb "large bandwidth" transmitters. VRT2 modules incorporate Lectrosonics’ new IQ dynamic tracking filters, which accommodate a wide range of transmitter RF power levels while also enabling extremely tight channel spacing—critical features as the available RF spectrum continues to shrink.
-
product
EW System Test Set
MS 1107
PSS LRU Test Set is used to test the RWR (Radar Warning Receiver) system by simulating the input signals and testing the output signals.
-
product
Rear Cover, G12, Tabletop Configuration
310113421
The G12 Rear cover is designed to connect to the Receiver in a Table top configuration and act as a mean to hide the cables that are running back to the testing equipment. This works well with applications where the cables are running down to a lower level below the G12.
-
product
Receiver, G10, 10 Module, For Slide Mounting (slide Kit Required)
310120146
*Please note: Consult procedure sheet/user manual for information regarding slight slide mechanism bracket protrusion downward into next U height on test rack on both sides of receiver.
-
product
Cable Assembly, Receiver, 72", TriPaddle, 50 Pin FML D-Sub
540111020503
Cable Assembly, Receiver, 72", TriPaddle, 50 Pin FML D-Sub.
-
product
12 Block Desktop Receiver
VGR12
VG Mass Interconnect products provide a common Universal interface for your custom test rack and simplifies functional test across your product line. Mass interconnect bench-top and rack mount receiver Plug and play interface blocks for signal, coax, high current, pneumatic controls, and more Stable proven products with 25 years in service Best cost of ownership Fast delivery next day on key products! Compatible to currently available test instrumentation and platformsThere are...show more -
product
700-800 kHz and 0.25 Degree Receiver Beamwidth Multibeam Echosounder
SeaBat T51-ASV
The SeaBat T51-ASV is built around the popular SeaBat® T51 and maintains the incredible SeaBat® data quality in a smaller form factor. Optimized power requirements ensure extended and crucial mission time on battery-powered vehicles. With full swath width at 700-800 kHz and 0.25° receiver beamwidth, there is no compromise between resolution and efficiency.
-
product
Cable Assembly, Receiver, 20", Micro Coax, 12 SMA Plugs
540099010147
Cable Assembly, Receiver, 20", Micro Coax, 12 SMA Plugs.
-
product
Cable Assembly, Receiver, TriPaddle, 20", 64 MOD to TB-4300B
540281010101
Cable Assembly, Receiver, TriPaddle, 20", 64 MOD to TB-4300B
-
product
EXG X-Series RF Vector Signal Generator, 9 kHz to 6 GHz
N5172B
Achieve faster throughput and greater uptime with cost-effective performance optimized for manufacturing testPerform basic parametric testing of components and functional verification of receivers with industry-leading ACPR, EVM, and output powerReduce the time you spend on signal creation with Signal Studio software; purchase only the waveforms you need with 5- and 50-pack licensingMinimize downtime and expenses with self-maintenance solutions and low-cost repairs
-
product
ARINC 429 Receiver
9429 RX
In addition to its wide supply voltage range from 18 V – 36 V the 9429RX module is characterized by its electrical isolation between the cRIO rack and the ARINC interface.
-
product
VXI Plug and Play Plate, 14U
310113364
The VXI Plug & Play Plate allows the 9050 VXI receiver to be mounted to a chassis with the Plug & Play Flange Kit from the chassis manufacturer.
-
product
Cable Assembly, Receiver, 20", Mini Power, 19 Pin to 4 Banana Plugs
540067010108
Cable Assembly, Receiver, 20", Mini Power, 19 Pin to 4 Banana Plugs
-
product
RF Hybrids
RF hybrids are used for combining multiple power line carrier (PLC) TX/RX units together onto one cable without causing interference between transmitters and receivers. They are also used for splitting PLC signals to go to two or three phases of a power line.
-
product
PIN-TIA
The fiber-optic coaxial PIN-TIA receiver module is designed for SONET/SDH fiber-optical communicationnetworks, using reliable InGaAs PIN photodiode (PD) highly integrated with low noise transimpedence amplifier(TIA) to convert a long wavelength input optical signal into a differential (or single) output. It is a highly reliablemodule with excellent performance.
-
product
Airborne Receiver
MS 2015
Receiver shall receive the telemetry signal transmitted by the airborne TGS unit. This unit is a single conversion super heterodyne FM receiver operating at 1486.5MHz. This unit has four connectors. They are RF input connector (J1), Power connector (J2), Signal connector (J3) for AGC signal and a Video output connector (J4). This unit operates at 28V DC and consumes a typical power of 5.6 watts.
-
product
VTAC, Patchcord, Receiver, 36", VTAC, USB 3.0, To USB 5 Gbps (USB 3.0, USB 3.1 Gen 1, USB 3.2 Gen 1) Type A Male
7-142890690-036
VTAC, Patchcord, Receiver, 36", VTAC, USB 3.0, to USB 5 Gbps (USB 3.0, USB 3.1 Gen 1, USB 3.2 Gen 1) Type A Male
-
product
Signal, Module, Receiver, QuadraPaddle, 480 Position, Fully Loaded With Twin Female Contacts And Round Posts (610138200 And 610138117)
510150135
QuadraPaddle modules are molded on .1” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. Allowing flexible configuration options with standard commercial connectors, QuadraPaddle modules are designed to fit any VPC pin and socket-based mass interconnect system. Available in 192 and 480 contact positions, QuadraPaddle modules accept standard .1” (2.54mm) pitch headers, breadboards, and connectors for direct PCB, ribbon cable, and other connections as well as discrete wiring.
-
product
Rotating Telemetry Systems
2100B Series
Advanced Telemetrics International
Are ideal for transmitting coupled data signals from sensors, which are mounted on rotating shafts or machinery to a stationary receiver.
-
product
Low PIM Coaxial Switch, DC to 26.5 GHz, SP6T
87106R
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87106R is a low PIM SP6T coaxial switch, operating from DC to 26.5 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency, and ultimately maximizes test throughput.
-
product
Quad 12 Gsps 16-bit DAC& Quad 4 Gsps 12-bit ADC
ADF-QMx44
The DEG ADF-QMx44 FMC leverages the Analog Devices AD9081 MxFE (Mixed Signal Front End) transceiver technology. This highly integrated device includes a quad 16-bit, 12 Gsps sample rate radio frequency (RF) digital-to-analog converter (DAC) and a quad 12-bit, 4 Gsps rate RF analog-to-digital converter (ADC). The ADF-QMx44 features an 8-lane, 24.75 Gbps JESD204C transceiver port, an on-chip clock multiplier, digital signal processing capability and supports four transmitter channels and four receiver channels.
-
product
Signal, Insert Bundle, Receiver, QuadraPaddle, SIM, Right Angle and Pass-Thru
510180107
Signal, Insert Bundle, Receiver, QuadraPaddle, SIM, Right Angle and Pass-Thru.
-
product
ITA, 9050, 50 Module, Double Tier, EMI, with 8" Enclosure
410104580
This 9050 ITA comes with an 8" enclosure for ease of system integration. The ITA is designed to work with the 9050 EMI receiver.
-
product
Micro Power, Contact, Receiver
610142106
(Available preloaded x2 in 510180102 Micro Power, Receiver, Insert)
-
product
90deg Hybrid With Balanced Receiver
This page describes one of Optoplex's innovated products, a 90deg optical hybrid integrated with balanced photo-receivers, which can be used in optical sensing applications, particularly the coherent Doppler wind LIDAR (light detection and ranging). Coherent detection has been widely found in applications for RF and optical communications. In the past few years, coherent technology has been advanced dramatically in high-speed optical communications. With this advancement, key parts and components are commercially available and cost-effective for many applications beyond telecommunications, such as narrow linewidth lasers, optical hybrid, balanced photo-receivers, and DSP, etc.
-
product
RF Down-Converter
CDC100A
Systems Engineering & Management
The CDC100A Series Down-Converter is a 1U rack-mount device designed for use with antennas that have a Tri-Band Feed. The CDCMA100 Series Down-Converter is a synthesized down-converter supporting 1415-1585 MHz, 1650-1850 MHz, 2185-2485 MHz and 4400-5250 MHz, down-converting 4400-5250 MHz to 1415-2485 MHz. The CDC100A is provided as a 1U Expansion Chassis that communicates with any SEMCO receiver via an RS-485 protocol. The communications I/O is via RJ45 and the operator interface is via the receiver RCMS GUI.
-
product
QuadraPaddle Modules
modules mount from the rear of the iCon receiver and ITA and allow installation and removal of pre-wired cable blocks. The modules also have captive Phillips head screws.
