Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI/PXIe RF Multiplexer, Single 16-Channel, 3GHz, 50Ω, SMB
42-875A-001
The 40-875A-001 (PXI) and 42-875A-001 (PXIe) are single 50 Ohm 16-channel RF multiplexers in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
product
RF Safety
MVG has developed a complete range of RF Safety instruments (Personal Protection Monitors - PPM) to measure the level of exposure to the electromagnetic field and to address the following needs:To continuously record the electromagnetic field level and alerts the user to potential overexposureTo monitor actual levels and compare them to the regulatory limitsTo address public concern through appropriate communicationTo simulate EMF radiation in real environments
-
product
SMART III RF Probe
Finna Sensors’ Smart III RF Moisture Probe is appropriate in those situations where NIR use on conveying systems/web applications or RF flat plate sensor use on board type products are not sufficient. Examples include tanks, bins, barrels, drums, Super Sacks™, silos, etc. These applications require a probe type moisture meter where the probe is inserted into, and is surrounded by product. Since the probe generates a 3 inch diameter radio frequency field around the length of the probe, a significant volume of product is measured. As the product is slowly removed from the silo, and refilled from the top, it passes by the RF Probe, thereby providing a constant real time moisture measurement. Typical applications would include starches, distillers and brewers grains, granulated chemicals or food ingredients, whole grains such as corn kernels, rice, soybeans, tree nut stockpiles, etc.
-
product
RF & Microwave Modules for 34980A
The Keysight RF and Microwave multiplexer modules for the 34980A Multifunction Switch/Measure Unit offer broadband switching capabilities for switching from DC to 26.5 GHz. Use these modules to route test signals between your device under test and your signal generator, oscilloscope, spectrum analyzer, or other instrumentation. A switch/attenuator driver module also allows control of switches and attenuators external to the 34980A Mainframe.
-
product
RF Shielded Test Enclosure, Low Profile
JRE 2214
Like its other brothers in the JRE test line, it features rugged welded aluminum construction with superb RF shielding effectiveness. Long life door gasket material along with double edge engagement not only provides solid RF shielding, but smooth trouble-free operation over its lifespan. Tough 'honeycomb' vent maintains shielding effectiveness throughout the full frequency range. Optional fan is available for additional airflow.
-
product
PXI/PXIe RF Multiplexer, Single 4-Channel, Terminated Common, 3GHz, 50Ω, SMB
40-876A-001
The 40-876A-001 (PXI) and 42-876A-001 (PXIe) are 50 Ohm 4 to 1 RF multiplexers with 1 bank in a single slot. Additionally, extra switching allows the common connection to be terminated into 50 Ohm, maintaining signal integrity. The module exhibits low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
product
HFC Analyzer
X16
The Kronback Tracers X16 is a DOCSIS 3.1 compatible suite of HFC monitoring tools such as return path analyzer, sweep system, downstream carrier monitor. Return path monitoring includes an advanced quality engine to log history information of noise and quality and alerts if ingress is present. Features such as NMS gateway and a dedicated RF switch increases the flexibility.
-
product
DC Blocking RF Splitter Combiner
PD5180
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)50 VDC maximum on DC block portTri Alloy SMA Female (Jack) 50 Ohm
-
product
RF Signal Strength Meter
006
Hand Held RF Signal Strength Meter. Detects RF Activity around centre frequency. Available for 315MHz, 433MHz, 868MHz, 869.85MHz, 914.5MHz.
-
product
PXI Quad 4 to 1 RF Multiplexer 3GHz 50 Ohm MCX Terminated
40-876-104
The 40-876-104 is a 50 Ohm 4 to 1 RF multiplexer with 4 banks in a single PXI slot. Additionally, extra switching allows the common connection to be terminated into 50 Ohm, maintaining signal integrity. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
product
400 MHz to 4.4 GHz, GPS-Disciplined OCXO, Reconfigurable USRP Software Defined Radio Device
783151-01
400 MHz to 4.4 GHz, GPS-Disciplined OCXO, Reconfigurable USRP Software Defined Radio Device - The USRP-2952 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless communication systems. Built on the LabVIEW reconfigurable I/O (RIO) architecture, USRP RIO delivers an integrated hardware and software solution, so researchers can prototype faster and shorten time to results. You can prototype a range of advanced research applications that include multiple input, multiple output (MIMO); synchronization of heterogeneous networks; LTE relaying; RF compressive sampling; spectrum sensing; cognitive radio; beamforming; and direction finding. The USRP-2952 is equipped with a GPS-disciplined 10 MHz oven-controlled crystal oscillator (OCXO) reference clock. GPS disciplining delivers improved frequency accuracy and synchronization capabilities.
-
product
WiFi / WiMAX RF Power Divider Combiners
INSTOCK Wireless Components, Inc
INSTOCK Wireless 2.4-6.0 GHz Power Divider, Power Combiners offer best-in-class performance for WiFi, WiMAX, 802.11b/g/n, and ISM signal splitting applications. IP67 outdoor weatherproof construction provides protection from the elements for uninterrupted outdoor use. All models available in 2-way thru 48-way configurations with Type N, SMA, TNC, BNC, and QMA connector configurations INSTOCK.
-
product
LXI RF & Microwave Matrices
Each of our RF & Microwave matrices is designed to have a controlled transmission line impedance and architecture developed to maximize the bandwidth of the product. The RF matrices are designed with crosspoint switch systems interlinked with isolation relays and loop-thru connections to minimize stub loading of the matrix. The mechanical and electrical freedom of LXI allows us to design RF and Microwave matrices to suit most applications.
-
product
RF Measurement
SAMbuddy-RF provides comprehensive analysis features for real-time RF measurement of DVB broadcastsThe comprehensive SNMP based monitoring capabilities of SAMbuddy-RF allow to establish powerful RF monitoring solutions
-
product
Activity Detection Unit
DG009-M1
Many advanced EW receivers, particularly those associated with ECM jamming systems, do not require the high resolution frequency information associated with a DFD or IFM based receiver. This is typically the case where a single pulse present within a broad frequency band is required to be detected and instantaneously down-converted to an IF band.TDS manufactures a range of Frequency Activity Detectors (FADs) also known as Activity Detection Units (ADU) which perform frequency measurement of an RF pulse and output data in as little as 15ns. The basis of these products is TDS’s ability to produce high performance broadband channelisers and integrated detectors. These devices are ideal for receivers which must operate in very high pulse density environments.
-
product
6 Slot PXIe Based Chassis with Embedded Controller
PXE6410
The PXE6410 is a PXIe based 6 based slot Gen 3 x4 chassis, that supports the Tabor Proteus Family of AWG’s and the TE330x family of PXIe RF amplifiers. The Chassis allows you to purchase any Proteus PXIe module and later add or up-grade to more channels, higher sample rates or higher output power.
-
product
LXI Microwave Multiplexer, 50Ω 6-Channel 11-Bank 40GHz SMA-2.9
60-801-411
The 60-801-411 is a 6-channel, 11-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
PXI/PXIe RF Multiplexer, Triple 4-Channel, Terminated, 8GHz, 50Ω, SMA
40-882B-003
The 40-882B-003 (PXI) and 42-882B-003 are triple 50Ω 4 to 1 RF multiplexers with 8GHz bandwidth.The 40/42-882B range have automatic termination of unused signals and are available as a single MUX in one slot, a dual MUX in two slots, or triple and quad MUXs in three slot s.
-
product
50 MHz to 2.2 GHz, Reconfigurable USRP Software Defined Radio Device
783923-01
50 MHz to 2.2 GHz, Reconfigurable USRP Software Defined Radio Device - The USRP-2940 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless communication systems. Built on the LabVIEW reconfigurable I/O (RIO) architecture, USRP RIO delivers an integrated hardware and software solution, so researchers can prototype faster and significantly shorten time to results. You can prototype a wide range of advanced research applications that include multiple input, multiple output (MIMO); synchronization of heterogeneous networks; LTE relaying; RF compressive sampling; spectrum sensing; cognitive radio; beamforming; and direction finding.
-
product
RF Spectrum Power Meter
SPM-50
SPM-50A Spectrum Power Meter brings innovative testing concept and approach for RF cable system installation and maintenance. It combines the key function of spectrum analyzer and power meter, designed to measure the power characteristics of particular signal among mixed signals transmitted on cable, fast and accurately present result in power histogram or spectrum chart.
-
product
50 Ohm BNC to SMA Adaptor Assembly
40-978-511-0.5m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
RF Signal Generator With 1.5 And 3GHz Models
TGR205x Series
150kHz to 3GHz (TGR2053) and 150kHz to 1.5GHz (TGR2051) frequency rangeHigh signal purity, phase noise <-117dBc/Hz (typical) at 1GHz output and 10kHz offsetAmplitude range of -127dBm to +13dBm0.1dBm amplitude setting resolutionInternal or external analogue modulations (AM, FM, PM)Amplitude can be set in dBm, dBμV or in linear Volts.Internal or external digital modulations - ASK, OOK, FSK, 3FSK, 4FSK, GFSK, MSK, GMSK, HMSK & PSK with U01 optionModulation SynchronisationFast amplitude and/or frequency sweeps with comprehensive triggering5ms sweep settling time1ppm frequency accuracy, <1ppm drift in first yearModulation waveform output on the rear panelInternal waveforms include: Sine, Square, Ramp, Triangle, PRBS (various lengths) and user-defined patternSimple operation with the colour touch screenProgrammable via USB, LAN (LXI) and GPIB (optional), SCPI compatibleCompatible with previous Aim-TTi RF generators
-
product
50 Ohm MCX to MCX Cable Assembly
40-977-561-1m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
LXI Microwave Multiplexer, 50Ω 6-Channel 7-Bank 6GHz SMA
60-801-007
The 60-801-007 is a 6-channel, 7-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
EMC
We will guide you through items that realize low-cost electromagnetic wave shielding measures (electromagnetic wave shielding: RF shielding), which is an issue at product development sites.
-
product
RF Adapters
SMA Adapters
Are semi-precision coaxial RF connectors developed in the 1960s as a minimal connector interface for coaxial cable with a screw-type coupling mechanism.
-
product
RF Functional Test Fixtures
EMC Technologies’ design team has developed a variety of test adaptors and test stations for testing RF circuit assemblies and microwave sub-assemblies.
-
product
RF Testing, Screening and Qualification
DPACI has extensive experience in providing RF testing, screening, as well as QCI services to a diverse range of customers, such as Lockheed Martin, General Dynamics, and Ball Aerospace. We have a fully equipped RF and microwave lab with test capabilities ranging from 40 GHz to 300 GHz for providing RF packaging.
-
product
RF & Microwave Modules And Instruments
SHF Communication Technologies AG
In digital high speed test and measurement, a perfect clock signal is crucial for the generation of low jitter reference test signals. A SHF Synthesized Signal Generator (Synthesizer) used as a clock source can operate over several decades of frequency and is an essential part of any high speed test and measurement environment.
-
product
Electromechanical Relay Switches
SMA SPDT electro mechanical RF relay switch features Indicators, Failsafe, Normally Open with an isolation minimum of 60 dB. SPDT electromechanical relay radio frequency switch PE71S6052 is part of over 40,000 RF, microwave and millimeter wave components available from Pasternack. Our SPDT SMA coaxial RF relay electromechanical switch can ship worldwide the same day that it is bought as with our other available RF parts.
-
product
Wideband Radio Communication Tester
CMW500
The R&S®CMW500 wideband radio communication tester is the universal test platform for RF integration and protocol development. It is available as the R&S®CMW500 callbox and the R&S®CMW500 protocol tester. The R&S®CMW500 includes a fully integrated end-to-end data solution that permits comprehensive IP throughput and quality measurements. Thanks to the internal fading simulator, it is easy to perform tests under realistic propagation conditions.